วีดีโอ

01:15 Could that be coaxed and aligned to index both pieces? And then T.I.G. welded into place?

Thank you for the great video. I was finally able to get my Windows VM working on truenas scale. I had a bit of a difference experience in that i download the drivers. Installed them as a cd rom on the vm and when the vm booted the network was already working. There still were some errors for other pci device drivers. So i ran the installer in the driver packaging and it seemed to clear up all of those issues as well. Now to continue on and try to finish my blue iris setup!

thanks man! this was really helpful

No sir, *Thank You!* 👍 As long as the "repairing person" is very careful then they will finish the job with the same number of digits 🤞 that they started with. *BONUS!!

What a shitshow Mercedes. Seriously. A fucking pressed on plate for twin turbo engines producing over 400hp. What could possibly go wrong???

i did all that and i have a code saying i have an open circuit or on the actuator switchover valve bank 2 also does the breather line plugs into the back of the manifold? theres two plastic things that stick out for two tiny hoses to connect to

Great You are The Best 🎉

Great job

Amazing guide, thank you!

Is this the same engine for a glk 300?

did it work out?

i understood about 5% of that. I am new to the world of TrueNas and VM. Thanks for sharing mate :)

Thanks man I didn’t want to take mine apart so thanks

Thinnest cotton gloves harbor freight sales, wear under your rubber gloves. I wish I had known it when I was working for a living. I discovered on my own. Try it long enough to get used to it before commenting. I'm trying to make a better world 🌎🌍 for all.

My Ryobi One+ 18v Lithium battery measures 15.79 volts with the outer jacket removed as well as prior to removing the cover. I have only this one Ryobi battery. How can I charge it enough so that the controller allows the charging port to begin charging it?

You know what the 3rd contact is for where the tool plugs into the battery? I would like to see if it's possible to run the impact driver on a different brand 20 volt battery and I figured out which was positive and negative but I don't know the 3rd one is for and the tool will not work when I only connect battery to only positive and negative. If you can help me with this I would really appreciate it. I can't find anything on the net other than it's positive but don't specify the voltage etc. possibly 5 volts?

Thanks. Whoever at Mercedes thought to put the gigantic airbox control valve right in front of the pulley I need to change can stub their toe already... and then making me replace airbox/intake gaskets to boot.

Thank you so much. Wonderful

poor instrructions. so much hand movement.confused

Are those caliper bolts used to attach the slide hammer?

Good video thanks. On my C350 M276 (2012) I was changing the serpentine belt and thought I'd look for the timing marks 40 and 53 degrees on the crankshaft pulley. The only marks I could see were the MB part number and that was only just visible, no timing marks visible at all. Anyone had experience of this ? Or is it just me ?

After 6 million camshafts, you would think MB would require their supplier to tack weld the timing ring in position. M278 is all the same hardware. Slipped pickup ring or broken adjuster both put them out of time.

I got the same engine m276 my car was leaking bad today I was thinking could it be oil Seperator I’m not no mechanic but I appreciate any one help god blessed

What temperature is considered operating temperature?

is this the first step to replace a crankcase breather pipe. should i be seeing is once i remove this.

Everything worked, except it would boot back to the windows installer even after installing it. Tried restarting a few times and I deleted the cd drive that was in the devices list already and then it worked. Needed to restart once more though but I saw progress. But don't delete the device you added, as you need another driver from that cd drive later for the internet connection. Thanks a bunch for making this!! It worked beautifully

What happens if the dip stick is grey at the end of the stick

Is this a hybrid motor

After installing timing chain tensioners I'm getting code P0021 (intake/left bank 2 timing over advance). I may have slipped a tooth on the driver's side intake cam. Would this check confirm that?

Where did you buy your parts & do you know the correct Flange diameter?

cheers mate

Can you get over 200,000 miles out of those engines???

Great thorough video, Thanks!

when and how i can configure main menu like in video - "display system process" "plugins" and other?

Couldn't get my battery to recharged after following your steps. It only charged up to 16.4v tied to another 18v. Two cells registered 4v and three cells registered 3v. Tried to charge individual cells with no success. Any suggestions?????????????????????????

Mine wont connect sometimes. Wtf?

How about a 2016 Tucson?

The yellow stripe vac line, where does it attach to? I pulled it off with the manifold and can’t figure out where attaches to engine side. Thanks

Very good video quality. And the pointy arrows in the video makes it even more professional. If you were to replace or access the valve adjuster on the LHS(drivers side) cylinders, how will you go about that? Thanks

Informational but agonizing to watch. This video could’ve been, should’ve been about 1/3 as long. You have to keep fast Forwarding to maintain your sanity.

Did you have to remove any of the shielding to get to the bolts?

Thanks for helping me get through this process! Way too tedious for an average joe like myself but that's what you get when you don't get a Synology box for 10x the price :)

16 minutes to explain at 3 minute job...

Tried a few other things before I found your video BrentH and none worked. Thanks for the easy fix♥

Thank you So much for this. Last time I changed spark plugs I didn't take off the manifold. Removing all the junk from the sides was a lot more of a hassle than just taking the manifold off the top. This video should be part of the 2014-2015 E350 video help.

this will not be a defective camshaft adjuster, the problem on all those camshafts codes are related to a defective camshaft, the wheel sensor of one of intake camshafts spins a littlet bit and set the timing code

Can you remove the front differential without removing the engine subframe? I have e350 2014 4matic with front humming noise wheel bearing are good and tires. The only thing that is suspected is front differential.

I have the same motor.. I’m having problems , my motor dies after about 10min , it won’t start back up unless I change the plug.. should I try this ?

I just got a E350 with 29,000 miles and I like it. I hope the engine stays around for a while

Thank you for your time and video, very helpful. For anybody doing ignition coils on drivers side, do yourself a favor and replace all of them on this side so you won’t have to deal with this again.