- 278
- 1 744 985
Adventures with Dr. Joe
United States
เข้าร่วมเมื่อ 27 ส.ค. 2010
As a retired plastic surgeon, I explore many areas of my current interests including repair, restoration, wood working, metal working, tool review, hunting, traveling, and farming. Please join me on my journeys through these different areas of interest.
6 Stage Reverse Osmosis Water Filter RTeview and Install
Review and install the Geekpure six-stage reverse osmosis drinking water filter system. A relatively new development is the sixth stage that adds back to the water calcium and magnesium and other minerals that improve the water flavor and quality. Step-by-step installation and discussion is presented.
Buy the Geekpure 6-Stage Reverse Osmosis Drinking Water System:amzn.to/4aJDnr1
* please be advised that the above link is an affiliate link, and I do receive a small commission if you make a purchase which helps support videos like these
As a retired plastic surgeon, I explore many areas of my current interests including repair, restoration, wood working, metal working, tool review, hunting, traveling, and farming. Please join me on my journeys through these different areas of interest.
#DIY #doityourself #howto #TheMoreYouKnow #Teach #Learn #DrJoe #problemfixed #problemfix #problemfixer
Buy the Geekpure 6-Stage Reverse Osmosis Drinking Water System:amzn.to/4aJDnr1
* please be advised that the above link is an affiliate link, and I do receive a small commission if you make a purchase which helps support videos like these
As a retired plastic surgeon, I explore many areas of my current interests including repair, restoration, wood working, metal working, tool review, hunting, traveling, and farming. Please join me on my journeys through these different areas of interest.
#DIY #doityourself #howto #TheMoreYouKnow #Teach #Learn #DrJoe #problemfixed #problemfix #problemfixer
มุมมอง: 13
วีดีโอ
Replace Heater and Thermistor for the Hot End PRUSA XL
มุมมอง 10914 วันที่ผ่านมา
The heater and Thermistor That heat and monitor the hot end of an extruder can fail and then you can't print your literally dead in the water. These can fail unexpectedly and you really should have a backup unit for these. A link is below where to get those. Step-by-step directions on how to replace these two items is carefully gone through so that it will be easy for you to make this change. G...
PRUSA XL PHASE STEPPING FIRMWARE REDUCE NOISE 90%!
มุมมอง 1.5Kหลายเดือนก่อน
PRUSA XL firmware update 6.0.0 Alpha was released April 24. It introduces phase stepping and calibration as well as many other upgrades. It reduces no ways from the printer by up to 95%! It is an amazing upgrade taking care of one of the issues with the PRUSA XL namely that it is very loud. This does not address the vibration significantly but boy does it help the noise reduction it is a very g...
RING Doorbell Battery Camera Install 1080p HD Video
มุมมอง 153หลายเดือนก่อน
Install RING Doorbell Camera Step by Step. This ring doorbell can be either directly connected to the low-voltage doorbell wires if you remove your doorbell and put this in its place or lithium-ion battery backup which is my selection. Both are described in detail. Ring Video Doorbell: amzn.to/3xxW6YH * please be advised that the above link is an affiliate link, and I do receive a small commiss...
SPIRAL CUTTERHEAD CUTTER ROTATION for THICKNESS PLANER
มุมมอง 1442 หลายเดือนก่อน
When you thickness planer starts to have results of an uneven surface you need to consider rotating the cutter heads. These cutter heads are made of carbide and last a long time but eventually they will wear and by rotating them 90° you have a fresh new cutting surface. Be sure to clean the under the cutters as well as the machined cutter head to be sure that the carbide cutters fit perfectly o...
PRUSA XL UPGRADE 5 PRINT HEADS 1ST RUN
มุมมอง 7832 หลายเดือนก่อน
This is the 1st run of the PRUSA XL upgrade from 1 to 5 printheads. A step-by-step process of getting all of the heads lined up and ready to print and describing all the adjustments is presented. This video describes the 1st run after the upgrade to 5 nextruders. Click here to order 1-Toolhead to 5-Toolhead Upgrade: www.prusa3d.com/en/product/original-prusa-xl-single-tool-to-five-head-upgrade-t...
PRUSA XL UPGRADE! 1 to 5 HEADS!
มุมมอง 9323 หลายเดือนก่อน
Adding Extra Toolheads to the Prusa XL From 1 to 5 Heads! Upgrade the single toolhead to the 5-Toolhead PRUSA XL step by step instructions. Click here to order 1-Toolhead to 5-Toolhead Upgrade: www.prusa3d.com/en/product/original-prusa-xl-single-tool-to-five-head-upgrade-tools/#a_aid=Jphunstad Click here to order Original Prusa XL: www.prusa3d.com/product/original-prusa-xl-2/#a_aid=Jphunstad EK...
Light it up! Add LED LIGHT TAPE to PRUSA XL Enclosure
มุมมอง 3873 หลายเดือนก่อน
Add dimmable bright white LED tape like to your PRUSA XL enclosure. Step-by-step placement of dimmable LED tail light is demonstrated delivering excellent illumination of the print bed. A low-cost addition to greatly enhance the visibility of your 3-D prints with the process XL. Click here to order 20ft Dimmable Super Bright 24V Led Tape Light: amzn.to/4bmy0iZ * please be advised that the above...
Filament Welding Easy and Predictable
มุมมอง 6534 หลายเดือนก่อน
Fusing or welding filament can be confusing and frustrating. This is a super easy method that is predictable reliable easy to perform and creates a very strong joint that doesn't need to be sanded, trimmed, or filed it's ready to go. Click here to order Adjustable Helping Hand with Magnifying Glass: amzn.to/3SBrUUH Click here to order 1/16" ID 3/32" OD 6.6 Feet Clear Silicone Tube: amzn.to/47V4...
OBXIDIAN Nozzle Install
มุมมอง 5124 หลายเดือนก่อน
The new PRUSA ObXidian nozzle can handle abrasive elements such as carbon impregnated fiber, glow-in-the-dark fiber inlet impregnated fibers. The black heat-treated nozzle is very durable and abrasion resistant. Step-by-step exchange with the standard PRUSA nozzle is demonstrated. Click here to order Prusa Nozzle ObXidian: www.prusa3d.com/en/product/prusa-nozzle-obxidian-0-6-mm-2/?query=?query=...
PRUSA XL REVIEW: A Big 3D Printer with Lots of Features
มุมมอง 6K4 หลายเดือนก่อน
The PRUSA XL is a new large-format 3-D filament printer. It is carefully reviewed and described in detail. Demonstrations of various printed models is noted and some crashes are depicted. Overall I have found this printer to be excellent and I recommend it highly. It is the single head printer. It can be purchased in a 1, 2, and 5 head printer model. This unit came semi-assembled which I think ...
Install Magnets for 3D Printed Parts
มุมมอง 2084 หลายเดือนก่อน
Install magnets into 3-D printer parts with a pin punch and a drill press. This method will allow the magnets to be in set perfectly plumb and level so that they will work their best. It's a very straightforward method that delivers excellent results. As a retired plastic surgeon, I explore many areas of my current interests including repair, restoration, wood working, metal working, tool revie...
3D Printer Fire Suppression
มุมมอง 3174 หลายเดือนก่อน
Fires can occur in 3-D printers. Realizing this, fire suppression is important to consider when you have 3-D printer. Adding a Blaze Cut Automatic Fire Suppression System is an excellent option for this. Step-by-step installation of the Blaze Cut system in a PRUSA XL 3-D printer is demonstrated. As a retired plastic surgeon, I explore many areas of my current interests including repair, restora...
Heat Press Magnets for 3D Printed Parts
มุมมอง 6944 หลายเดือนก่อน
Heat pressing magnets in 3-D printer parts can secure them beautifully and perfectly in a vertical position. This will allow the parts to come together very well. If the magnet is slightly larger than the opening don't despair because when she heated up, the printed part will melt allowing the magnet to sit in place and it secures it very strongly. Warning: If magnets are heated beyond the temp...
Filament Dryer for 3D Printer with Upgrade
มุมมอง 1.7K5 หลายเดือนก่อน
Here are the links for the to filament drive boxes I purchased. They range in price from $65 to as low as $38. I bought each one for $38 so you may have to wait a little bit until they drop in price. Although they have different names they are virtually identical. Click here to order your Sovol Filament Dryer: amzn.to/3S1BdN9 Click here to order your Comgrow 3D Printer Filament Dryer Box: amzn....
Vibration Reduction Feet for the PRUSA XL
มุมมอง 3595 หลายเดือนก่อน
Vibration Reduction Feet for the PRUSA XL
Mercedes Benz GLE KEY Fob Battery Replacement
มุมมอง 5K5 หลายเดือนก่อน
Mercedes Benz GLE KEY Fob Battery Replacement
PRUSA XL ENCLOSURE ASSEMBLY and REVIEW
มุมมอง 6K5 หลายเดือนก่อน
PRUSA XL ENCLOSURE ASSEMBLY and REVIEW
UNORIGINAL PRUSA DRYBOX ASSEMBLY and REVIEW
มุมมอง 4.6K5 หลายเดือนก่อน
UNORIGINAL PRUSA DRYBOX ASSEMBLY and REVIEW
Heat Set Brass Inserts Placement and Tips
มุมมอง 2305 หลายเดือนก่อน
Heat Set Brass Inserts Placement and Tips
Heat Set Insert Heat Pressing Machine Assembly and Use
มุมมอง 2795 หลายเดือนก่อน
Heat Set Insert Heat Pressing Machine Assembly and Use
BOMBAS and DARN TOUGH MARINO WOOL SOCKS SHOWDOWN!
มุมมอง 1K6 หลายเดือนก่อน
BOMBAS and DARN TOUGH MARINO WOOL SOCKS SHOWDOWN!
Assemble the PRUSA XL 3D Printer with me! (Part5)
มุมมอง 6136 หลายเดือนก่อน
Assemble the PRUSA XL 3D Printer with me! (Part5)
Assemble the PRUSA XL 3D Printer with me! (Part4)
มุมมอง 4676 หลายเดือนก่อน
Assemble the PRUSA XL 3D Printer with me! (Part4)
Assemble the PRUSA XL 3D Printer with me! (Part3)
มุมมอง 4036 หลายเดือนก่อน
Assemble the PRUSA XL 3D Printer with me! (Part3)
Assemble the PRUSA XL 3D Printer with me! (Part 2)
มุมมอง 5396 หลายเดือนก่อน
Assemble the PRUSA XL 3D Printer with me! (Part 2)
Assemble the PRUSA XL 3D Printer with me! (Part 1)
มุมมอง 1.1K6 หลายเดือนก่อน
Assemble the PRUSA XL 3D Printer with me! (Part 1)
Stihl 2 in 1 Chainsaw Sharpener Filing Guide
มุมมอง 14K8 หลายเดือนก่อน
Stihl 2 in 1 Chainsaw Sharpener Filing Guide
Hey Joe.. this was interesting.. But I was wondering why so many filters.. even a salt water water maker doesn't have as many.. Just curious. Wait 2 gallons waisted to one used.. that doesn't sound to smart to me.. unless of course that 2 gal. goes back to your water heater for showers, toilets and the like.. you should have explained that a bit more because it doesn't make sense to me.. Plus you should have tried the water at the end and given us a rating of your water now or your water measured against bottled water.. Well carry on my friend.. I like your ideas and the fact that you explore things like this for our benefit
no audio
I’m so sorry you had a problem with that. I clicked on the link you sent me and immediately came up with sound. I don’t know what’s going on. Sorry about that. Thanks. Joe.
@@JosephHunstad I have no idea either. other videos are ok. I run into this every once in a while.
Great information. I’m having an issue with the remote. It sometimes takes me pushing the button 5 times before the gate opens. It beeps and everything, it’s like the signal doesn’t catch until after the 5th or 6th time. Any suggestions why that is? Does it on all remotes. Hit or miss.
Thank you for your comment and question. I’m glad you found the video helpful. I would probably replace the battery or the remote as a first thing and be certain when I use the remote. It has a clear line of sight to gate opener. Apart from that, I’m really not sure. Consider subscribing. Thanks. Joe.
Hi Dr Joe Like you I have purchased and tried numerous grease couplers. The screw to lock is effective but a little slow! The more expensive (better quality, we hope)lever types are my pick. Have a lock n lube and find it good. They all seem to dribble a small quantity of annoying grease when disconnected.
Great comment. I agree totally. Even the lock N lube. The most expensive one by far dribbles. It’s nice that you can lock them in and not have to hold pressure against the fitting which is very helpful. Consider subscribing. Thanks. Joe.
Hi Joe Pull the chain around to next tooth in the opposite direction to what you are doing in video ie away from power head - reduces the chance of cutting a finger on a tooth - great video.
Hey John, thanks for your great suggestion. I will definitely do that. I’m glad you found the video useful. Consider subscribing. Thanks. Joe.
Thank you for your video. However, regarding 1:13 & 11:33, that 10 millimeter retaining nut is not "Nylon". Instead it is made of steel. This is because nylon is plastic and would be too soft to withstand the rigor of retaining the pivot bolt. You can verify that the nut is made of steel by confirming that a magnet is indeed attracted to the nut. On the other hand, nylon or plastic is not attracted by a magnet.
Thank you very much for your comment. Yes, you are right. It is a steel nut, but it is a locking steel nut and I believe has a nylon insert to prevent it from changing position. Thank you again. Consider subscribing. Thanks. Joe.
Thank you! Luckily I have all the tools to get this done 🙌🏼 even if you wanted to just buy another one you can’t anymore - they are off the market. so I’m gonna give this a try!
Hey, that sounds good. I hope the video was helpful. It does work just step-by-step instructions. You’ll get there. Take care. Joe consider subscribing thanks.
@@JosephHunstad subscribed! 🤗👍🏼 thanks again!
I have a weird situation it's a push to close(standard) setup...I am able to setup the close limit but not able to setup the open limit....it just opens and closes itself doesn't stop...
Hello DR. JOE, I wanted to thank you and congratulate you for this superb creation of this drybox which I printed without any problem because your stl are so clean without any fault, however I would like to ask you if there was a version of the stl ( beam A1 and A2 PC4 M10) 5 pc4m10 instead of the 6 that you propose because I opted for the version (5 Spool auto rewinder adapter for (un)original Prusa drybox MMU3 / MMU2S Repbox) thanking you very much if you respond, cdt
I like mine. Unfortunately I think I lost my charging 110 and 12v.
That’s no good sorry to hear about that. All of the elements and mine are still working. OK, which is good consider subscribing. Thanks. Joe.
This video is seriously underrated. Super clear and complete explanations. I have never sharpened a chainsaw, so I watched a few youtube videos on how to use 2in1 and was still confused. This video answered almost all my questions (a close up on the tooth while sharpening would be perfect ), and now I feel much more confident. Thank you!
Thank you very much for your nice comment. I’m glad you found it useful. Yes, this is a great sharpening device. That does everything you want all at once and makes it actually a very quick and predictable outcome. Consider subscribing. Thanks. Joe.
Good comment about the close-up. I’ll try to reshoot this.
@@JosephHunstad Thank you very much for reading and replying to viewers comments! Subscribed. One question: I regularly cut tree logs along the grain, as an "old man's" way of splitting firewood. Is there anything different or need to know when sharpening a ripping chain, vs regular chain?
Hey buddy, fantastic question. The vast majority of chains are crosscut chains. A rib chain has fewer teeth to bring out the very long strands. But sharpening is the same. Thanks for your question. I’m glad you’ve subscribed. Take care. Joe.
I dissolved about 35 feet of nickel battery strips into about 1.5 gallons. It's an intense teal-green color. I'm having fun with bicycle parts and old tools. I'm using a vintage 3.3-volt DC 2-amp phone charger.
That sounds like a great idea. Yes, you can use such a large quantity and then nickel plate. Much larger parts this fantastic. Consider subscribing. Thanks. Joe.
very good explanation thanks for all the information
I’m so glad you found it helpful. Consider subscribing. Thanks. Joe.
I bought a jeep with a winch didn't come with the control so I bought a wireless one. The winch works but only when it wants to and I'm having difficulty figuring it out any suggestions
Periodic electrical problems are a real challenge to fix. First thing I would do is replace the batteries in your remote and then check the wiring on the winch to be sure it’s all stable and solid and properly tightened. Tough one. Consider subscribing. Thanks. Joe.
Do you know where I can get the o-rings/seals kit for Central Hydraulics item 92782? O-rings seals kits from Harper Freight Tools don't fit.
Hey, that’s a really good question. I’m really not sure but if you’re able to measure the O-rings, you might be able to buy those on Amazon. Thanks. Joe.
USA 🇺🇸 ❤, 👌👍💯
Thank you for your thumbs up. I am glad you enjoyed it. Consider subscribing. Thanks. Joe.
Excellent video Joe! Your video on rebuilding this floor jack was very detailed and informative. You didn’t take any short cuts or Mickey Mouse anything. You accomplished a great rebuild on this floor jack. Thanks and BTW I subscribed to your channel and rang the bell(as Scotty Kilmer would say “ring that bell”).
Thank you very much for your kind comments. I hope you enjoy your rebuild. It was a lot of fun and now I have an incredible jacket as good as or better than New. Thanks for subscribing. Take care. Joe.
I currently have a winch quick connect installed with a keyed power source. Would I be able to run another wire to the same keyed source? Or is that unsafe?
I think it’d be absolutely fine. If you only use one at a time, it could get overloaded if you had them both working at the same time. Good question. Consider subscribing. Thanks. Joe.
excellent.. just what I was looking for..
There’s nothing like using sharp well prepared tools. I hope you found that video useful. It makes using a hollow Chisholm Mortimer a joy versus a pain. Consider subscribing. Thanks. Joe.
@@JosephHunstad Oh yeah.. I have used chisels for the last 73 years.. I thought this would be easier for me now.. But the dang thing wouldn't work.. Now I see my mistake.. it was so obvious.. I have subscribed now and can't wait to go through your video's
Well informed explaining of the switch. Great Job Thank You
Thank you very much for your nice comment. Consider subscribing. Thanks. Joe.
Nice review Joe! Wondering if any different kind of material you'd like to try for 3DP'd parts? We'd love to sponsor and reach any potential collab together? (PCBWay zoey)
Hello there. Yes I would enjoy collaboration. Let me know the products that you’d like me to review. This printer is pretty amazing and I think we could highlight your products with it very well. Thanks. Joe.
I’d like to know what products are available. I’ve used PLA, PETG, ABS, TPU(not very well), I have not tried the carbon reinforced fiber or others. Thank you. Joe.
@@JosephHunstad Hi Joe, would like to have a further discussion, may i know your email?
@@JosephHunstad Hi Joe, would like to have a further discussion, may I know your contact info?
jphunstad@gmail.com
They are almost life time blinds, you are correct. They have a 25 year warranty and the company does honor and stand behind the product. I know because I have several of them. Just to clarify you called this a Muddy Blind several times. It’s a Redneck, different company.
Used these for my diesel pump so any vehicle or a dc power supply can power it. They work great.
Hey man, that’s great. Thanks for sharing. They are fantastic connectors. Consider subscribing. Thanks. Joe.
This just the video I was looking for. Will the ALWAYS KEYED ON drain the battery?
Hey, I’m glad you found this helpful. If you have something running on that always online guess it will drain the battery for sure but if it’s not connected to anything using power, it’ll be OK consider subscribing. Thanks. Joe.
Is the handle made of plastic?
No, the handles are steel. They’re covered with the rubber coating though to make them more comfortable. Consider subscribing. Thanks. Joe.
I used yours to build inspiration for mine...I cheated a little and found it a little and cut the bottom recesses as well as the top and bottom out with a CNC router. I designed a half circle and rectangular top mashup that I sawed in the middle like yours before drilling for the magnets. For those without a CNC using your method, you can easily replicate by running through a dado stack on end to square up the top recess...or with some patience, a single blade.
Congratulations that sounds like a fantastic way to go. I’m glad that I was a little inspiration for you. Consider subscribing. Thanks. Joe.
Question from a newbie, if I'm going to cut wood that has nails in it, would I use the wood blade or the steel blade? And thank you for the demo sir!
OK, that is an excellent question. There are blades made that are literally for wood with nails in it. You can find those blades made by Bosch at Lowe’s or other places and that will definitely take care of the situation. Consider subscribing. Thanks. Joe.
Great stuff. I had just bought one of these, and I was getting frustrated with the filament outlets getting bound-up and kinking filament. Who would have thought the spare couple of pneumatic fittings I had would be a perfect fit? By the way, how long/often do you run these? Have you (or anyone else reading) ever hacked one to run 24/7?
I have not hacked mine to run all the time the longest it can run as you know is about 12 hours and I really use it a lot particularly to dry things like TPU. Consider subscribing. Thanks. Joe.
what speed that i can use?
8GB Single DDR4 2400MHz
I think I found my channel for 3d printers stuff
Hey, nice to talk to you again. I do a lot more things than just 3-D printing, but I do love 3-D printing. I’ve got a new video coming out in the next day or two on replacing the heater and the mister on the high end you might want to check out. Thanks. Joe.
Thank u
You are very welcome. I hope you found the video useful. Consider subscribing. Thanks. Joe.
Which one use battery?
The Michael Kors watches that are quartz watches all use batteries. Consider subscribing. Thank you. Joe.
thanks to your video I am going to try to fix my Stihl BG 75 blower myself. The shop around the corner wanted to charge me $200 to $300 to fix it. I will let you know how it turns out
Hello Darryl. Thank you very much for your nice comment. You’re gonna find the rebuild is actually a lot of fun and when it fires up, you’re gonna have a big smile on your face. I hope you find that video useful. Please give it a thumbs up and consider subscribing. Thank you, Joe.
Thanks for a great help. My old pad wore out and just put a new one. The bottom screws rot out after a while and it made the unit to fall off.
Hey buddy, I’m very glad you found it helpful. Consider subscribing. Thanks. Joe.
Can you get the replacement gear for lowering the jack? My gears are broken off ?
You know that’s a very good question. I know which gears you’re talking about the pinion gears. I have not looked into that and I do not have a readily available source at this time if I find what I will try to get back with you. Consider subscribing. Thanks. Joe.
I have a 2022 Rzr with the old terminal block in the same spot. I wonder if I can upgrade it to this pulse bar instead, and how difficult it would be.
You ask a great question. It should be easy to connect because it just needs a negative ground a positive power terminal and then the switched or blue terminal. What’s those three are connected your pulse bar is good to go and then you just need to find a good spot to mount it.when you remove the old block, take a look for those three wires. Those are key wires to connect to the pulse bar. Consider subscribing. Thanks. Joe.
Hi doc, thanks for sharing, I just received my XL and I am building an enclosure for it. I am thinking on adding these feet to reduce vibrations. Did you notice a significant improvement? Thanks!
Hey man, I’m glad glad you got a printer. You’ll love it. The most important thing is to download the new firmware that’s reduced noise by 90%. The feet help but they’re modest they’re not huge but I like them so it’s another thing to help things, but the bottom line is the firmware is super critical. Thanks buddy. Have a good day. Take care. Joe.
@@JosephHunstad Thanks Doc! 😉
Great information! This info is exactly what I was searching for regarding my filament dryer. Parts ordered.. Thank you!
I’m so glad this was helpful for you. Were you able to order it through the information in the description below? I do receive a small royalty for that but you pay exactly the same price. Thank you for your help. Consider subscribing. These filament dryers are great. I actually have three of them, take care. Joe.
I see you are using the Encloxure I have the a 2 head which i upgraded to the 5 head i have been trying to print polycarbonate with the enclosure closed and found the high temps required for PC i get heat creep blockages that kill prints now where before the enclosure i mostly only had to deal with warping and problems related to that warping off of the bed.
Thank you for your comment. Yes I like that enclosure a lot. It was fun to build and I use it continuously. I have not used polycarbonate so I can’t comment on that. Pelle and PETG work great. TPU or flex doesn’t work at all. I’m having a lot of trouble with that and I’m very frustrated. Do you have any TPU suggestions? I hope you can resolve your issue with polycarbonate. Consider subscribing. Thanks. Joe.
You could have just used a short piece of pipe to fill the gap in the angle iron, but if you have a welder everything looks like a welding job! I want to get one actually.
Thank you for your comment. Yes you are absolutely right. I could’ve just put a piece of pipe there, but I have a welder and yes, it was an ideal welding job. It made an L turn into a square which was a perfect piece to mount the spare tire carrier on.get a welder it’s great. I don’t use it as much as I’d like to but boy is it handy and it’s a real fixer. Consider subscribing. Thanks. Joe.
The one pound canisters are well over built. The procedure used to refill the bottles is low risk in my opinion. The pressure in the 20lb tank as well as the 1 pound canisters is low. The tank structures can likely take thousands of pressure cycles. Look up the fatigue life of carbon steel. Everyone needs to assess their risk level and make their own choice.
James, thank you for your comment. I totally agree with everything you said, but I had to put some caution caveats in my video description because of my worry of liability. The 1 pound cylinders are indeed very heavy duty and unless there’s some sort of trauma to the 1 pound bottle itself I have, no concern about refilling these. If there was an issue with the integrity of the 1 pound bottle for sure I would just toss it. Thanks again. Consider subscribing. Joe.
Balance is a non-issue. The saw is being supported by the wood you're cutting. DeWalt fanboy.
Hello Harry. Thank you for your comment. Yes you’re right. The Saw is definitely supported, but I just felt more comfortable with the balance, moving it around changing positions, etc. By the way, I also have Milwaukee, which I like a lot too. I do like DeWalt, but I’m not married to them. Consider subscribing. Thanks. Joe.
Hello, Are you interested in testing our products? We would like to invite you to test the Front Bumper for your Polaris Ranger XP1000( if your car year is 2010-2023
Yes, I would be interested. Would you like me to then do a review on that on TH-cam? Thanks. Joe.
@@JosephHunstad Yes, please share your con tact way. Thanks
@@StarknightMT_official The way you are adding spaces to avoid deletion by youtube spam detection is a little concerning. Why would you even post this as a comment vs following up privately with the channel owner??
This was helpful!! Thank yoy so much!
Thank you for your comment. Consider subscribing. Thank you. Joe.
Excellent instruction!
Thank you very much. I hope you found it useful. Consider subscribing. Thanks. Joe.
Well, I hope you found it helpful. I’m sure the water separators are pretty similar regardless of brand. Consider subscribing. Thanks. Joe.
TH-cam in it's infinite wisdom brought me here when I searched "Takeuchi Fuel Water Separator" I imagine it's the same general ideal so works for me. Thanks for the video.
Turn the belt inside out when taking it apart and reassembling it.
Hey there. Thank you for your recommendation. Next time I change I’ll I’ll do that. Thanks. Consider subscribing. Joe.
Thx! Great video instructions. FYI, to remove the hydraulic unit, you don’t have to take all that stuff off. Just the cotter pin and the two side bolts. Raise the lift arm by hand, and then the hydraulic unit then just slips out the bottom.
Yes, thank you very much for that. You are correct. I appreciate that. Consider subscribing. Thanks. Joe.
I'm sorry i missed the part where you purchased the rebuilt kit?
There is a link in the video description click more and you’ll see that link link. Thank you.