- 13
- 161 269
Snapsum L
Hong Kong
เข้าร่วมเมื่อ 31 พ.ค. 2020
I create this channel to show some of the minor fixes I did on my car as well as anything that may be interesting. As I feel finding somebody that i feel comfortable and I can trust sometime is not easy and send an old and used car to dealership, the cost is really high. Hope you like the channel.
Please bear in mind safety is the priority. If you are not clear the proper procedure and safety measures, please let somebody help you to fix for you! I will not carry any responsibility for yourself as well as the property of your fix involved. The video show here should be used as reference only.
Snap sum means summing up the snap work as a whole to get diy finished and fun!
Please bear in mind safety is the priority. If you are not clear the proper procedure and safety measures, please let somebody help you to fix for you! I will not carry any responsibility for yourself as well as the property of your fix involved. The video show here should be used as reference only.
Snap sum means summing up the snap work as a whole to get diy finished and fun!
2014 Ford Kuga 1.6 transmission fluid change COMPLETE process #Unijack #Mercon LV #OBDLink MX+
In this video, I drained my 2014 Ford Kuga transmission fluid and filled it. This is a COMPLETE process coz this included the initial fill, initial oil level measurement/ check. Then hot measurement with proper car level method. For safety consideration, a 2T Unijack has been bought. For transmission fluid temperature check, an OBDLink MX+ was used (both original software or Forscan was fine to do so).
All tools used has been described at the beginning of this video.
All tools used has been described at the beginning of this video.
มุมมอง: 7 469
วีดีโอ
2014 Ford Kuga Escape 1.6 battery replacement
มุมมอง 1.5K2 ปีที่แล้ว
In this video I replaced the 12v old battery with a new one. The tools I used are listed as below: 1. Gloves 2. flathead screwdriver (small and large head) 3. 10mm hex socket short to medium length (battery bracket, terminals) 4. 13mm hex socket long and extension, wrench 5. Vise grip plier 6. Electrical insulation tape 7. Wet clothes for cleaning 8. rubber band and a clean bag for covering the...
2014 Ford Kuga Escape Cabin Filter replacement
มุมมอง 1.1K2 ปีที่แล้ว
The cabin filter part number i'm using for 2014 1.6 Ecoboost Kuga: AV6N-19G244-AA (From Ford made in Germany for Kuga) H2MJ 19G244 HAHF (From China Motorcraft, Taobao 翼虎)
Engine oil filter cut open with a can opener?
มุมมอง 1.7K3 ปีที่แล้ว
In this video, I tried to disassemble the engine oil filter with some simple tool - can opener. No angle grinder to prevent the metal dust as to examine the filter element. Tools: gloves, eye protection, household can opener, flat head screw driver, bench vise. After cut open if successful, you can see the components of an oem filter e.g. anti drain back valve, over pressure relief valve (bypas...
14 Ford Kuga Escape Cowl Panel removal and Valve Cover Oil leak inspection
มุมมอง 4.1K3 ปีที่แล้ว
This video to show how I remove the cowl panel of Ford Kuga. Most of the time, it is required to take out this panel to allow you to work on your engine compartment. For example simple tasks like spark plug change, to ease of battery removal and installation, and valve cover inspection. Tools: 1. hex wrench, 10mm hex socket for cowl panel screw, 15mm hex socket for windshield arm, trox screw fo...
14 Ford Kuga Escape brake lamp bulb fail and replace
มุมมอง 4.5K3 ปีที่แล้ว
This video created to show how I change the bulb of the brake lamp Tools and materials required 1. V small flat head screw driver 2. 8mm hex socket and wrench 3. P21 5w bulb (depending on your model)
14 Ford Kuga Escape engine light on: change coolant bypass valve (DTC P26B7)
มุมมอง 4.7K3 ปีที่แล้ว
This video created because my Kuga pop up engine light after I drove uphill with a bit of little hard push on gasoline pedal. After scan thru via OBD tool, DTC P26B7 found. With internet search problem should be the engine coolant bypass valve. Although the dashboard temperature was normal, it is wise to not drive the car until the problematic part will be replaced. Car can still be driven afte...
Ford Kuga Escape tail liftgate problem dropping struct replacement (non drive size)
มุมมอง 11K4 ปีที่แล้ว
In this video Im going to show you how to replace the struct on my Ford Kuga (non drive size ie. without electric motor). I bought my new struct from Amazon as below for your reference: Ford CJ5Z-78406A10-B, Hatch Lift Support by Sneed Ford Parts Learn more: www.amazon.com/dp/B00M37XZQY/ref=cm_sw_em_r_mt_dp_Bv0DFbZ6FB83S FYI the struct was produced by STABILUS. For proper disposal of the stored...
14 Ford Kuga, Escape, Fiesta ST 1.6 engine oil change and engine oil warning light reset
มุมมอง 9064 ปีที่แล้ว
In this video I change my Ford Kuga 1.6 2014 engine oil and reset the warning light after finished. The Ford manual mentioned I need WSS-M2C948-B spec 5w-20 oil. My dealership gave me M2C945A. I believe they share similar spec and I bought a bottle of Castrol as below. For my Kuga oil filter I use the one coming from dealership from UK. For Ford Escape I think it require FL910S as shown in my v...
Ford Kuga Escape coolant leak change coolant reservoir bottle degas bottle
มุมมอง 13K4 ปีที่แล้ว
My Kuga encountered a problem the coolant leaking and it was found the bottom and the side of the coolant reservoir (ford called it degas bottle) cracked. I recorded a video to show you how I change the bottle to a new one with some experience sharing that you may find it useful for you.
Ford Kuga / Escape wheel lug nut chrome cap problem
มุมมอง 7K4 ปีที่แล้ว
In this video I am going to show you why you should replace all of your 14 Ford Kuga / Escape wheel lug nut DPAccessories LCS3A6HC2CH04024 24 Chrome 12x1.5 Closed End Spline Tuner Lug Nuts for Aftermarket Wheels Wheel Lug Nut www.amazon.com/dp/B00JNEBQWK/ref=cm_sw_r_cp_apip_l1rv2C2lHQYOW
How to fix MTB mountain bike brake noise squeal (pad)
มุมมอง 984 ปีที่แล้ว
My mountain bike front brake started having squeal. After cleaning the brake disc with brake cleaner and the pad with some soapy water, the situation improved. However, near the end of the brake level pressing, high pitch noise still coming out. Decided to swap to a new pair of pad and noise removed. Examined the pad and looks like it's still over 50% unused. Decided to see what can be done to ...
14 Ford Kuga / Escape Abs light fix. #Kuga #Escape #OBDlinkMX+ #Forscan
มุมมอง 104K4 ปีที่แล้ว
My Ford 2014 Ford Kuga 1.6 / Escape pop up an Abs light, ESC light, Hill start assist not available message. After a few weeks of annoying message, I decide to diy and perform a fix on this. Tools required: 3 ton jack, jack stand, nut socket, breaker bar if required, torque wrench for wheel nut and wheel speed sensor, 1/2 electric impact wrench, locking pliers, Torx bit, new wheel speed sensor,...
My tailgate goes up and straight down to lock
Awesome video Thankyou for making this repair these videos help so many people
Some people's time appears to be worthless.
we are the power tailgate factory
How much miles on original transmission oil? On this car
Show us how u get and install the forscan
Can u give the exact link where u bought the OBDlinkmx & the software that u used for doing that.
How did u get the OBDlinkmx app ? How did u buy it ? And did u use forscan or just that OBDlinkmx app u bought ?
Ridiculous video. There’s a reason you don’t show the removal or replacement. You have to basically bend the filter to get it in and completely misshape it. Then good luck trying to get the cover back on
Its because the ABS unit is looking for all wheels to be spinning at a similar rate. if one wheel spins then the count from the sensor on that wheel will be different than the others, hence an alarm state! Theres just too many sensors on vehicles these days. Brake warning sensor for low brake fluid "YES" but different rates between wheels? Overkill. There is also way too many audible alarms on vehicles, like you open the door and the car beeps at you to tell you the door is open! What should be available on all vehivles is the ability to turn the audible alarms down, actually it should be mandated!.
Just changed all my discs and pads but found same problem found with all lug nuts. Got them off eventually but realised it would be impossible to change wheel for spare if I got a puncture so have ordered a full set of new solid ones.
Hammer and chisel, plyers and sore hands but managed. Such a stupid design. Best bet is to hammer the brace onto them as long as the cap hasn't rotated inside. Realised that after picking the others off bit at a time.
Hello mate...big help.. cheers
Same happens with tighter steering and turn into limp mode And no hill start assistant displays. Please help me. I have replaced the abs sensors of all four wheels seperately when this occured earlier. Last time when this happened i replaced the abs module too. Then now again.please help me. Even the dealership also not doing a proper repair🙁
Have you tried to check any code with an OBD scanner?
I have a question did you replace the whole chord or did you just retape it
i did not replace the electrical line connecting to the sensor
Does this have a transmisson filter?
there is transmission fluid filter but not in regular maintenance
Why......
Just experienced this exact problem. Well done Ford !
Thx dude
Update: the valve in the video made in China last ab 2 year with 28000km. Just changed a new valve (ford parts in the description)
Got a ford ranger with similar fault, near side front ABS sensor needed replacing
I have issues my kuga 1.6 ecoboost right now. My extend coolant hv crack same like this video. 2 pin hose also cant stick to the coolant. Every day fill up the water. Now tank water leak back of the engine. 1. My engine light warning. 2. Where can i get the coolant tank and big and small hose with pin. 3. Water leak and cant see where come from.
the material aged and broken e.g. hose connector. you can try in online parts store or amazon (US).
I got mine from Amazon
What tool did you use with the units "Nm" and why is it needed?
it's torque wrench to help you tighten screw properly
thanks great video
i've got the falty code p1934 in my ford kuga 2015 related to speed sensor, is it possible my problem be the front wheel sensors because all the scanner i've used just show this code. PS: when the lights come on my car gets in limp mode and the go away.
www.dtcdecode.com/Ford/P1934
did you drain the coolant system before you replace the reservoir? or did you just drain the remaining coolant in your reservoir?
try to suck out as much as you can from the reservoir and drain out the coolant from the connecting hose near end. I didn't drain the whole coolant system
@@snapsuml8796 Thanks mate, I just disconnected the top thin hose first, then lifted up the bottle and keep the bottom opening with the hose facing up, and disconnected the big hose. Not a single drop of coolant spilled. 😁
@@chrisdonn4794 Perfect! Coolant is no good to our environment
My Ford Kuga 2015 had the same warnings as shown. Turned out to be the rear near side speed sensor. Quick fix (there are two type for my model and are colour coded....choose the correct one !)
Hi I have a 2015 Kuga with this problem,replaced the abs sensor that cured the problem but not the lights on the dash so I was wondering which colour did you use on yours.
Why would driving up a hill do this ? Is it safe to continue
it was the moment my Kuga engine light turned on. The fix should be carried out asap to avoid any further issue that may arise from the faulty parts
Guna gunting bos 😁
This is better than the others I found. However I can't take out the light and don't want to break it 😐
for the light have some form of shaking in different directions and hope u can take it out. for the bulb it's bayonet mount just twist it. good luck
Great video thank you!! Fixed 2013 Kuga UK spec.
Why is it called degas?
Both water and coolant contain dissolved gasses that are driven out below the engine operating temperature producing high pressure. For safety reasons, when these hot gasses release, a hose directs them downwards to ground level. This only vents EXCESS pressure, so it does NOT make it safe to remove the bottle cap when the engine is hot.
A pair of tin snips works easier.
do you have any symptoms for this bypass valve failure? for me, have burning engine oil smell from the car engine.
If there is some abnormal smell, can check any oil leak signs and symptoms. Is coolant temperature normal? can remove the splash guard to check under the engine compartment. In addition, u can have a look from my other vdo ab 'cowl panel and valve cover inspection'. For my case, there shouldn't be other immediate problem. However, it's not sure other problem can be caused as the valve is connecting to the coolant passage.
Hello, Thanks for the video. I recently have the same problem. Can I just remove the engine light by using OBD tool without really replacing a new coolant bypass valve? (I understood this is not a proper way to solve the problem, but my situation was below: 1. the same engine light appeared 2. I use OBD tool tool to scan the car, also can see the DTC P26B7 code. 3. After scanning the car, the engine light disappeared. (somehow maybe i have deleted the code, I am not sure) So, does this mean the bypass valve was not really the problem? ( I mean , if it is really the problem, we can never remove the engine light until it was really reparied/replace/fixed). Thanks
Hi Michael, if the DTC disappeared after delete, it means it's normal again. However, if it appears again, the root cause should be found and treated. It should be the problematic part sometimes working sometimes no.
I have the same issue. The abs light come on and the off traction light it also give me the same “no hillside assistance “ reading. But it only stays on for a minute. It goes away and at random times it turns on again. I have a code reader but it does give me any codes. Could it just be a bad sensor?
i think it should be the bad sensor. Maybe your code reader cannot read the ford codes that can tell u the exact wheel
Did you fix it?
I think the moral of this video is: Use tin snips instead. Lol.
I took my 2014 ford kuga in for 160 000km service and they identified this leak
I think I have the same problem, did your car have overheating issues?
No overheating for my car. Only fluid did leak from the cracked coolant bottle
Master 👍👏👏👏👏
Thank you! Your video was the only one I could find that gave a solution to my problem.
Thats good can help u
Update on my 2016 Ford Focus SE 2.0 L. Both hill assist not available light and traction control light turn on them off. It was bad tire balance which ruined tire. It had bald spot and I drive it to work which ripped out a chunk of thread. Replaced it and rebalance it. No more lights and very smooth ride. Also before this checked and rebalance one tire. Should've checked the other one too. And not very noticeable vibration coming from steering wheel. Only a lil . Wasn't even sure.
If changed a single tire and the other side is still old one and of different brand, obviously it is uneven weight across the left tire and right tire, and this may be the reason w still a tiny little vibration from steering. Thanks for sharing
Wow, there are so many things that trip that message.
I have 2013 kuga 2.0 tdci raving high 1100 rpm usually all cars are about 800 rpm any solution to bring it low
I don't know what Kuga is. Mine is 2016 Focus SE 2.0L. Hill start assist not available light and traction control light also on. Someone said it's wheel sensor. One said wheel alignment is off. My feedback vibration on steering wheel at high speed seems a bit more than before . Have you heard wheel alignment might be cause also ?
Hi Frank Montez, if vibration at high speed but steering is straight, it may be caused by uneven weight across the circilar motion of your tire and wheel （front or rear wheels）usually you have to do balancing it after tire change. For the instrument light it is can be checked easily with the OBD tools （with ford support）. If your steering is not straight, there may be other issue （eg control arm ball joint aging, tie rod ball joint aging）if your vehicle is in high mileage and it better to check those parts before wheel alignment （or even after alignment it may get worse result） one other possible reason is uneven tire wear. Usually i will have tire rotation for every oil change. Maybe your car have both abs wheel speed sensor and the possible causes i mentioned above.
@@snapsuml8796 yeah it was bad balance . Ruined my tire. Replaced and balanced and now hill assist and traction control lights are turned off for at least a week. Much smoother ride.
Is it safe to drive the vehicle when this happens? Can this damage anything in the vehicle if i continue to drive it?
In my case my car could still be operated and might encountered tight steering right after start up. Please refer to Owners manual for the instrument cluster. Usually if the message indicator is Red, you should pay more attention as that may indicate a critical failure.
Disconnected abs sensors right &l eft during repair I need to clear the abs codes now without scanner
How Do I clear the. ABS Codes and turn off the light
@@locnload1 I not quite sure what u mean 'Disconnected abs sensors right & left during repair'
I'm having the same issue with my Escape and the code reads U3000-48 with a definition of software failure. I'm not sure what to do. Any suggestions?
U3000:48 -> Control Module: Supervision Software Failure. Action: Clear DTC. Cycle the ignition. Carry out ABS module self-test. => If the DTC returns, install a new ABS module / HCU (hydraulic control unit) assembly. If the DTC does not return, the condition to set the DTC is not present at this time. This cause may be intermittent
@cyla bridges did you ever get that fixed? what was it?
Hi may I know where can purchase and how much of the price ?
Hi you can refer to the description i put the amazon link there
Seems that one is currently out of order. Just found this as below, or you can try other parts store like taaca parts or fordpartsgiant Ford CJ5Z-78406A10-B, Hatch Lift Support by Dealer Sales Solutions LLC. Learn more: www.amazon.com/dp/B00M37XZQY/ref=cm_sw_em_r_mt_dp_FC1PMBTA08JVW2QJBB81
Plz can you mention the model/serial number of the abs sensor
Front sensor i used for my Kuga BV6T-2C204-FB, in US for 14 Escape 1.6 front it should be HV6Z-2C204-A. For rear pls double check with the dealer as AWD and Auto park should have difference. Hope this can helps
Thanks brother very useful for my Escape 14. GOD BLESS YOU 🙌
My ford escape has the same alerts, and the descent brake is deactivated, which you recommend me to do, it will be that the module is not damaged or only the abs and speed sensors, I greet you from Ecuador, help me
Hi David Osejos from Ecuador, if you have a OBD reader that can read Ford code it will be more easily to find out the DTC so you know exact code and wheel. If you don’t have the reader, I have seen somebody changed all four wheel speed sensors. Please be reminded the front and rear sensor are different and they have different part no.
I had the same dash lights pop up, along with much tighter steering. Would all this be due to the speed sensor?
With the lights on i experienced tight steering a few times （but not always） after just starrted the engine and drove at the beginning. According to this it maybe. However you should check the code to identify the exact reason and if it is to see which wheel
@@snapsuml8796 I have a different reader. It didn't give me the wheel speed sensor faul like yours did. Mine reads: "Invalid data received from anti-lock brake (ABS) system control module"
@Jason Bryant i think your reader trouble code was U0415. I ve double checked my report and it had this code also and it come from ECU Power Steering Control Module, while my vdo code C0034 comes from ECU ABS system. Seems U0415 is a more generic code.
@@snapsuml8796 You are right. The reader gave code UO415, but didn't give any more specific details
I have the same problem, the steering becomes hard and not always, and the brake is deactivated when descending a slope, some tell me that it is an abs module, what solution have they given you so far?
A very good video for Kuga drivers, hope to see more videos about kuga maintenance. Thank you