วีดีโอ

The pressure plate itself did not allow the transmission to come out

Thank you for watching. I honestly don’t remember where exactly but you can find them on eBay

It usually takes me 2-3 days to get done.

Sorry for the late response. I havnt done a 4runner that is 4x4 but i do know it is very similar to this job. Usually you will need to remove the front axles and also some applications you need to remove the transfer case in order to make it easier to removal the transmission. As far as the output shaft it is easy to reinstall but often time if you are struggling to put back the transmission often time what I do is loosen the bolts to the pressure plate then realign the clutch plate by reusing the alignment tool that the kit comes with

I did mine and it’s 4x4 I pulled the transfer case and then the tranny as it was lighter that way and was easy hardest part was separating the tranny and engine once it was separated it went back together really easy it did t even fight me

@@drezzgarage8150 Thks mate

@@garygibby526 Thks for your insights, will be done next week!

@@eduzancaner the clutch usually comes with and alignment tool it’s a plastic splined shaft that holds the clutch disk in place while you bolt up the pressure place so when u install the transmission the input shaft slides into place and is all aligned the pressure plate torques down and holds the clutch disk in place with the alignment tool in place then once tight it’s held then u remove the alignment tool and install the tranny the input shaft will slide in easily after that step I usually put a dab of grease on the input shaft splines and the tip where the input shaft bearing sits as well. There’s a bearing that goes dead centre on the flywheel and is actually tapped into the machines hole in the crankshaft so make sure u don’t forget to replace that as well it’s not hard to tap out the old one and tap in a new one that way the input shaft has a fresh bearing as well as the pressure plate release bearing this all came with my clutch kit I got a stage 2 set up so it’s got more clamping power than stock and was decently priced have fun with your project I sure did now I daily drive mine and love it on and off road

Mine won't come apart.either fml

The 4R in this vid is 2WD standard. 4WD would be similar but have to deal with the transfer case.

This was a 2wd

@@garygibby526 most likely the pressure plate is stuck just like mine was

@@drezzgarage8150 mine was an accidental 2wd purchase I didn’t realize it wasn’t 4x4 lol so I quicky swapped it to 4x4 after I got it.pretty happy now it’s rust free being a USA import and 2 wheel it had never been off road . Got the clutch out

Not sure what you are asking?

@@drezzgarage8150 do you have a part #? Did you make it yourself?

@@jbhuts oh for those…honestly the car isn’t mine and it already had it. Im sure you can find something on eBay or go to a local junkyard to see if you can find one

@@jbhuts www.ebay.com/itm/255516831230?_trkparms=amclksrc%3DITM%26aid%3D1110006%26algo%3DHOMESPLICE.SIM%26ao%3D1%26asc%3D20190917065201%26meid%3D4f87bf3d56f046c094d197e28907d8ea%26pid%3D100935%26rk%3D4%26rkt%3D12%26sd%3D284894239510%26itm%3D255516831230%26pmt%3D1%26noa%3D0%26pg%3D2332490%26algv%3DSimplAMLv9PairwiseUnbiasedWebCpr08MlcGreedyV3%26brand%3DToyota&_trksid=p2332490.c100935.m2460&amdata=cksum%3A2555168312304f87bf3d56f046c094d197e28907d8ea%7Cenc%3AAQAHAAABEIxnp208POpAtEdSbeoza%252FtzyQmh2SBqORzgyIzbrfwKs8mDYiJnIRJg4GvE9THHqZ0Nnxk2mYxCNRsOPTo8FhqF8Q1Zor1L%252B48rpEWJ5EP%252Fyij2oleGj7oHZIevwtNLWu%252BZnrmZi0%252BTXayqOiEzaMKZYE26ycM8XTlFASsEKnYUhky8zTtJlX9SkXod75ycR3fgfQVaQiJT%252Bslb%252F%252FstIUojFCvC0r5dtZG%252Fcx00LmMRf5M0w51FZOU6LvawpclSFenf3BssA4KDPFtXdxuW6tKRgfEmrcM9VfJ54dsrYgSeAtIScf7Lu50ZflW6JnBWeSokdGNiZgNWtDzYZV%252FC97L5U1SeictjunBTlX4wNU9y%7Campid%3APL_CLK%7Cclp%3A2332490

Thanks man. I'm always trying to find a way to kick up my 4Runner a notch. I like those add'l outlets...but my center console is perfect, and even my clock works! Thanks for the reply!

Yes I am planning on doing that as well

Thanks for the comment. I am planning on having a video on that especially prepping the car for the track

👍