วีดีโอ

Champ thank you. Changing my diff oil from Port Vila Vanuatu

I've been looking for gutter guards for a couple weeks now. Saw these yesterday in Lowes, they looked promising. I dry fitted them in the store on gutters they had on the shelf and noticed the flange really didn't lay flat on the outer edge of the gutter. Thanks to your video I now see that they have to be bent to conform to the roofline. Like you I have a 12/12 pitch. I'm going to pick up a couple boxes in the next week. If all goes well I'll go back and get enough to finish the entire house.

Would appreciate any suggestions. 2012 Polaris 800 Razor EFI hesitates at 45-50 mph. 45 is about 6350rpm. Not really a sputter or cough. Repairman just cleaned throttle body and fuel injectors and said idle air circuit was partially open causing a misfire at that speed. None of the work performed solved the issue. One person suggested the primary and secondary cluthes might be fighting each other. Need to get it fixed pretty quick so we can sell it and move, but I want it to be right. I should also mention that it has full power no issues 0-45. No codes, no engine light. Always at that speed only.Thanks. Appreciate anything.

Going to check with my neighbor, who just installed them with many Large oak trees in his backyard, but some reviews show with this type of guard they May tend to build up leaves on top of them, I have a high pitched roof , but wondering when you bend them down if they will collect more debris on top of them

Thanks for responding. We bought my parents vacation home which come with this similar spa. We can't find the manuals in the house or much information online pertaining to the key pad and operation of it. Looks like leisure bay went out of buisness. We can get parts, there's a sequence to entering the temperature is what we've found so far. Thanks and be good.

What model is this?

So what was disconnected? It would of been nice to see that because i have no idea what to disconnect

Thank you for this super helpful video. I could never have imagined that lint buildup could cause such a crazy amount of noise!

Thanks for the video! Great tips... while I don't have the mesh, I bought Atlas and it's a good guide.

I appreciate the video, I realize I will just reverse the steps but I would like to see a video of the actual disassembly as well, do you have that video or know of one for this model? Haven’t been able to find one

Shouldn't the valve be facing the top of the spring?

Perfect instructions, My dryer was vibrating and sounded like a plane taking off, it sounded like it was coming from the front where the exhaust fan is, and when I applied pressure to the door and front of the machine it would quiet down a bit. Seemed like it was the fan. I followed the disassembly instructions, removed about 3 cups of built up lint from the fan blades, cleaned the housing, reassembled everything........Like new, Thanks

Hey My 11 rzr800s grinds while trying to shift between gears at idle . Do you think it could be my primary clutch

Did it work

Do you have a link for the light bar?

Wheredidyougetrearrackextender

What’s the coast?

I literally just fixed my squeaky noise. I took pictures but no video. The problem was the pulley/ pin that’s right next to the blower motor pulley. I had to file down a bit the pin and then greased up and lined up the pulley and I’m good to go.

Really wish someone would record the noise so I can see if it’s what I’m experiencing. Hundreds of Maytag repair videos showing how to take it apart, but not the noise they are fixing!

Never seen a blue one. These are awesome atv's, surprising the amount of power they got. Im 6'1 215lbs and it fits great and hit the limit 51mph no problem with me on it. Light steering, great handling and suspension and well built. I put tech screws in the tread blocks and had a blast riding on the rivers and and trails during winter.

Surprised that ladder didn’t slide on you with that angle 😂

Be careful on that ladder. Your angle is way too shallow.

Mine just started squeaking. Any videos on how to fix that issue?

Onde vc compra peca de mtor dele ?

I hope those work out ok for you. I will say that between your steep roof pitch and how fine the micromesh is I think you’re at risk for the micromesh getting clogged and rainwater running over the edge of your gutters especially during hard downpours. I live in Michigan so I have snow and ice to worry about so i don’t think I could use that product because the small spacing between the micromesh will freeze up and clog it. I just used rolls of 1/4” galvanized hardware cloth from the hardware store (much cheaper than the Atlas product). I feel 1/4”spacing in the hardware cloth mesh is plenty small enough to keep debris out that might clog the gutter and is big enough to avoid clogs that would cause rainwater to run off the edge of the gutter.

Is there any way to remove the front panel without taking the dryer out? Doesn’t seem like it but ours is stacked and gas so I’d rather not take it out of its cabinet if I can help it.

Mesh gutter covers *will* stop leaves and other large debris from getting into gutters but large amounts of pollen (a few pine or cedar trees close to the house) can and will plug the screens quickly. They can be cleaned easily with a brass brush, but don't expect them to be maintenance-free... they're not. You will still need a high-quality ladder. The problem is worse with low-end DIY products as the low-chromium stainless steel screens age and begin to rust, and they *will* rust. Stainless steel is not stain-free and as always you get what you pay for. Buyer beware.

Do you have to hold your foot on the brake to put in to park?

Impact gun? NO you need a drill

do you need to screw it in? or using the sticker side would be sufficient

I just ordered these. I am curious, have you done any follow up on these? My concern is winter. I live in the NE area (Massachusetts to be exact) and I was wondering how these perform with snow and possible ice damns.

Do you live in Minnesota

If you shim the secondary clutch and get the belt in the center of the primary it may help. But if it’s still turning the belt and secondary at idle then you have to replace the one way bearing on the primary. Until then I recommend shutting the rzr off and shifting with the motor off the keep from damaging the transmission.

Super helpful video!

Did it fix the problem?

It's your bearing. It's probably sticking. When u started it. The secondary should not spin.

How do you like the T connection? Would you ever consider doing each side with separate air lines to pressurize individually? Any down sides to connecting them together like you did? Thanks!

I see sun light on them and that’s a great thing for these so they dry up fast. Show us in 2-4-6 years if your able to.

I just bought this yesterday! Your video definitely helps me feel like I can do it!!!😊 thanks.

I had mine for about 1year 2 months and total night mare

So you just received it... how is it your favorite

any thoughts on not undoing the adhesive and leaving the tape side and just use the screws in case you need to unscrew them for any reason if you need to clear anything under the cover?

Great job! Thanks for the time you took.

How fast did it go with the 115?

Just got one for my nephew he loves it.....

Commando, historia for pabor, asap

You having the solid metal strip flat with the gutter will now collect debris where the screen and the solid metal strip meet . It seems all gutter guards keep the debris out of the rain gutter but the debris stays on top of the gutter guard

I have had to remove some gutter guards from very steep roofs.

Does that truck have a sunroof? can you get that truck with one or are they only available on GMC?

He has low range? Manual