วีดีโอ

Like the info but a close up would help. Thanks.

Unfortunately, the placement of the turboprop nacelles are in line with the old piston engine CL-215 model. The 415 nacelles should be located more inboard. I have seen this corrected and the kit can be built up nicely. There are other faults with the kit but the nacelles Placement is the worst of the lot.

nice

Im looking at dishwater softener, rain-x, and awesome cleaner.

I NEEDED this!!! I was wondering this stuff wouldnt come out of my brushes!!!!!!! Thanks!!

Can i use paint brush for tamiyah?

I'm still learning about painting with tamiya paints and this is the video I was looking for. When I opened the paints, they had a strong smell for the chemicals, so I am thinking on buying a filter mask, because I work on a small space and doesn't have proper ventilation and keeping them on a wooden box (because it's fresh) to prevent the chemicals activate with the heat

Deck-els?

Fantastic. About how long did it take you to do this?

Very nice job. Larry Landis

Oh man. This is bringing me back to my childhood. I remember buying these and tester paints at walmart in the 90s. Couldnt remember the company that made them

Good real advice brother. Wish I'd seen this video before I started experimenting with acrylics, Tamiya in particular, after a 55 year hiatus in model building. Those are most the principles I have discovered by trial and error. Good vid.

Some say with "ammonia" some say without 🤦🏻‍♂

Fine line tape will minimize rough edge

Do the commercial acrylic airbrush cleaners have IPA in it?

does the model kit wheel height, is it too high thats why you cut off the rotord?i was trying to listen but you have a low sounding voice. cc dont work 🤨

Great technique

From England, great stuff, thank you.

thats too bad the ride height seems a little high. i wish revell did those kits with just a smidge lower ride height

😮❤

Very good.

"Don't spend alot of time on the diorama " ? Bad advice. If your going to do a diorama, do the best you can.

This is real artwork

Great video!

I actually have now a CL-215 of Heller and build the Heller one is the same as the Italieri

Me gusta tu trabajo, buen trabajo y me gusta más el que no hayas abusado de los envejecidos dichosos, un saludo

Thank you for the tips

You can use an alcohol calculator so you can add water to know 99% and bring it down to 70%. IPA quite expensive here in Australia could I use methylated spirits aka denatured alcohol? I heard you can make flow improve over from dishwashing rinse aid. 3mls to 1 litre of water. Cheers Graham

I know this a long time later. But what did you clean the panel line with?

Excellent work. One question. At minute 25:59, you make a mix, what is IPA?

OMG this is genius. Thank you!

Can i use water to thin my tamiya paint?

Where you can buy it

Why didn´t you use the decals?

I just tried tamiya lacquer..and in preparing to use it I think I was confusing it with this acrylic hybrid or whatever this is lol.

I'm going to use testers silver bottle paint to refresh my front hood letters of my Land Rover. I just subscribed and I watced this video. Will itself level straight out of the bottle? Should I use a small bristle.brush like the one in this video? I know the importance of don't over brush and keep moving. (I have a bottle of Testers thinner too) Thank you .

I've used Future for sevral years, applied with a brush, and had very good results. I was lucky, when I bought it, it was under 10.00.

Great short video! Just wondering what size needle you’re spraying with? And can the Pledge be thinned down if I’m spraying with a smaller needle?

Why I cannot drink, obvious joke hehe, thanks for the video :)

Awesome video! I always wanted to add to my body paint but was lost on the technique. Great and clear instructions. Thank you

I shake my paints by hand. They always are very thick near the bottom of the bottle. After watching this, im guessing, its because im not stirring? The sprue trick is great.

Just picked up some Tamiya Flat Flesh Acrylic for my Astro Boy figure the paint around the Neck is cracking I hope this paint Does the job the figure was kinda pricey

Maybe really thin the Tamiya before painting, seems to work 👌😎☕️

Nice work! Love the song too. What is it?

Would be cool if the picture quality was better.

Hello, may you have a recommended Enamel paint/type/brand to be using for scale model cars and planes?

Nice build

Thank you for sharing; May you have a GoTo paint/brand/type for hand brushing car details? (i.e., engine, interior, shocks, etc.)?

Pretty cheap and easy to make!

sick! I love 61's