วีดีโอ

That is a great video and explanation - thank you. I feel I need to learn the basics of electronics - research started!

Very good. I hope I have same problem.

I've seen many videos where people think just adding solder to the old relay is an answer. But that is just a stop-gap measure that buys some time & the problem will recur. The issue is with the internal relay contacts.

The under-spec-ed relay trick is a very popular one in the appliance industry.

MBAs: Why sell sell an appliance that last 20 years when you can sell an appliance that needs proprietary replacement parts every 3 or 4?

I will never call an appliance repair guy...UNLESS the appliance is still under warranty. It's way too easy to rip people off in that trade.

You're a smart man,thanks for your imput. That service fool owes you some money!

Thank you for the thorough detail about the relay and PCB. Your attention to detail is superb and beautifully explained. This video directed me to a failed solder connection on the reverse side of the PCB to the relay. It was a failed solder joint. The existing 10amp relay was fine and the fault was fixed by re-soldering the relay tab coming through to the other side of the PCB. May God bless you Seth LaForge. He blessed me by directing me to your video! 🙏

Thanks for your video. I have a Siemens dishwasher that is having this problem and presents the error E02 on the panel. I think that the cause is probably something like this because I had the same problem around 3 years ago and it solved by itself after a few days while I was waiting for the assistance to come. Does it make sense that it got fixed by itself? Maybe a connector slightly move and started working again and now failed again?

sounds good , I'll order one of those 16 A relays . Oh , i guess if I'm going to be doing some soldering , I better get a new bottle of MAP gas for my plumbing torch. 🙂

Thank you. This was very helpful and my dishwasher is back up and running.

Nice bike, but a haircut will not hurt, it's unfresh 😅

I have a Bosch shx series dishwasher that was not heating. I checked the control board and it looked fine. My board is easy to access behind the door. I ordered a new heater assembly after checking the resistance at the connector on the control board that supplies the heater. It showed open and should be 11.5 to 12.5 ohms. ( it turns out that you can't check the heater this way) After looking at the new heater assembly, they incorporate a flow sensor switch that is in series with the heater. I pull out the dishwasher and remove the right side panel to access the heater and measure the resistance. It checks ok. I then find a wire hanging loose and not connected to anything. After looking at the wiring diagram I discover that this wire comes from the control board to one side of the capacitor for the main pump motor. The spade connector had corroded apart and fell off of the cap, preventing the main pump motor from running properly. New five cent spade lug fixed the problem. I would suggest anyone with a no heat issue check the board as described in this video and also check the heater resistance directly at the heater before ordering a new heater assembly. It could be something simple as in my case.

Dddff ffhh😴😴😯😯😯😯😉

Awesome video!! Last week was appliance hell as my microwave burned a flame sensor (there was no flame or excessive heat), my refrigerator lost the cheap plastic pins holding in the switch for the through-door ice dispenser, and my [Bosch] dishwasher failed to heat the water. In my case, it WAS the water inlet valve. I don't like being my best appliance technician (I'm not an appliance technician) and I appreciate helpful people like you making these videos. None of the videos out there directly solved my problems, but the approaches and clear thinking led me to about $600 in savings. The difference between the water inlet valve problem and the relay problem is that I had some heat and the dishwasher was always hot and steamy when it was done. With the relay problem, I would assume you would have no heat ever.

À froid, il ne faut jamais accélérer!!!

Wish I had one

Thanks so much for doing this video. I had the same problem. I ordered the parts from your links below and soldered the new relay switch on the circuit board. My dishwasher works great and I don't need a $1200 replacement.

Una autentica bara....non frenava tantissimi morti era meglio la honda

1st thing I noticed

Carbs need balancing.

no choke !

Цепку натягни!!!

Was that it, spent more time trying to start the fcuking thing,, FFS

just rev the crap out of that cold motor, then wonder why it's so hard to start.

vas apprendres à démarrer une moto au lieu de faire une vidéo de merde que la moto ne mérite pas

typowy angol,chuj im w morde

der Typ braucht mal einen Oelwechsel. Aber natürlich schwierig wenn man ständig am Zweitacker schnüffelt

I have done many dumb things in my life and one of the dumbest was selling my h1

He was flooding it

His chain is about to come off, it's loose as heck.

You need air in those tires and your kickstarter detent spring is worn out. Hard starting is a problem that I could not suffer when I rode two stroke engined motorcycles in the 1970s.

'Promosm'

Sounds like my old H1, loved that bike.

Them carbs definitely need attention

Where's the H1 at?

Engine sounds very tight, it's the way it stops turning so quickly with each false start.

Thank mate .

Hallo, i suspected this relay in my dishwasher but i dont beleave it several days while i am searching to fix the problem. Thanks.

Hey man thanks from an Appliance Tech going on 27, years I just started repairing Bosche dishwashers. This vid helped me tremendously

Bosch 800, cold water only - fills to top of filter, replaced heat pump, no burn marks on Control board ,,, any thoughts or suggestions?

Chain is loose.

Great job!!!! I just diagnosed the same problem today while out on a service call. Many service people are just parts replacers. I actually ohmed out the heating circuit then tested for voltage at the board instead of guessing. I sleep better at night that way.

Be safe, but have fun. You'll get it figured out.

速く走れ。

What about a fresh haircut for the biker…?

This is great. Thanks for making the video. I have a Bosch SHE55R56UC/64 which very similar to yours. Would I use the same part as your model?

Expantion chambers sound great!

Ned's rings! To low compression!