วีดีโอ

How can I tell my zone numbers, I have seven and want to know which is which, thanks

I had a dude paint the crown after he installed it and now it’s peeling …. Should I seal instead of painting the new one ?

This just confirms that I should not attempt this, because to me #1 looked to not match the others even when finished. What were the symptoms that caused you to think you had a carb out of sync??

SMH you explain how to take it apart and put it back together but nothing about what you're looking for when you're adjusting. What an I looking for on the gauge?

Explain what you're doing while you're doing it. SMH. I watched a 10 min video, it should've been 5. Lol

E eccezionale sto strumento

Hello Willow thank you so much bro!!!🎉

Who see this wonderfull video 2024? 🎉

Hello, I have a section that doesn't work. I'll follow your video and keep you posted. One dallas irrigation wanted around $800 to fix my issue. Another question, my system has 6 zones on my system. Looks like yours, have you change out the main controller?

Is the plywood/backer board free floating until concrete is installed or do you screw the backer board to something?? Is the overhang of the hole 1” or what’s the backer board lip to edge?

Are permits required for this type of work ?

Hey man i know its a long shot on you responding. Are the two vent lines on the fuel tank important to have on?

Great video thank you! Very nice bike also. Ride safe

music sucks and is annoying

Plywood?

Ci vuole vasca ultrasuoni per pulire

Fatto io uguale

Thanks bro!

What happens if you didn’t prime your auger at first use 🥶?

+1 for using a magnet on a stick through the oil fill hole to guide it in.

why there are a lot of negative echoes on the R6 models from 1999 until 2001 that a lot of engine and engine block failures. And that models up to 2001 should be avoided. I found a 2001 first hand with 8000 km in almost new condition but I am hesitant for fear of ending up with an engine that fails.... I even had a dealer who advised me not to buy…. Can you tell me if you had problems with yours ? Or there is différence with Europeen models ? Thank you

Geniale.

Thank you! Very clear instructions to do changing oil & air filter on Toyota Tacoma truck.

Good job but the music is horrible!

Another tip, you can repolish jets and mixing tubes with 0000 steel wool. Leaves a factory finish on them that lasts

I've got a thundercat, is the process exactly the same? New to riding and (very) novice at any mechanics

Missing 1.5-2.0 inch drip edge. Water should drip onto roof not run down sides of chimney. Also cement is used for crown not mortar.

You need to start making newer videos. You have some quality stuff. This was great!

One of the best powder coat gun reviews I have seen. I not only appreciate the DIY fixes you provide, but the reason for the fixes were probably the most valuable. Great job! Thank you!

This video shows how not to fix your chimney

Need to use cement board not plywood

You're the best.

Thank you

Very nice ! Helped me out a lot.. Thank brother !

Hack

mortar. This isn't what mortar is designed for and it WILL NOT last. Mortar is used for masonry joints. Cement with rebar is FAR superior. Also, simply running a bead of whatever caulk around the flue is DIY mistake.

Question should you have cleaned mortar sooner so it doesn't leave all that residue.

He almost understands how to powder coat

Subscribed. Thanks bro

combustible material in chimney????? not to smart, better check your building codes

you should do a video on how to replace a detent spring

This video is four years as I’ve watched it and it’s helped massively thank you 🙏

Hi willow , what is the diameter for this specific hose you used for the calibration ? and the t adapter , can you provide some links?

Freakin!!awesome video STRAIGHT TO THE POINT . Thx

Yeah, better lighting and we can speed up the video on this end. People are missing the finer details with the in this case 16x speed of the video.

Great, is the direktion of the rotation important or the same for the flame? I mean in the case of water is the tornado only in one direktion.... or?

what's up buddy ? I'm from Brazil, I have a motorcycle like yours, I had already disassembled and reassembled the carburetor once and everything worked fine, but the last time, my wife took and mixed the carburetor parts to use the container I was using. help me please. 8mm wrench, Flathead or other piece does it have to be adjusted or is it just screwed in all the way?

What a beautiful job 👏🏻👏🏻👏🏻

Great video, thanks!

Thanks for the video man. I learned something to clean my own Carburetors appreciate it.