- 5
- 61 381
RushTactics
เข้าร่วมเมื่อ 20 พ.ย. 2017
Surf Trailer 4k 1080p
THE SURF TRAILER (thesurftrailer.com) is the ultimate solution to get your board or boat to the water. Whether you're a seasoned surfer or a new kayaker, our trailer helps you transport your equipment efficiently and comfortably. With sturdy construction and easy maneuverability, you'll forget you're even towing your gear. So pack up and hit the road with our bike trailer, because with us, it's always Bike. Beach. Repeat.
มุมมอง: 7
วีดีโอ
Infinity G35X Upper (Third) Brake Light Replacement
มุมมอง 8K2 ปีที่แล้ว
Step by step DIY video for how to replace the upper (third) brake light assembly in the 2004 Infinity G35X.
Majestic Propane Fireplace Pilot Assembly Install
มุมมอง 53K6 ปีที่แล้ว
Step by step instruction for how to replace the pilot assembly on a 500DVBLPSC7 Majestic Direct Vent Propane Fireplace. The old majestic part number that I bought was P/N 80D0007. It appears this has been replaced with another part (20308982) but I can't speak to the exact wire and tube configuration.
You go into such great detail about how many fastners and where they are... you show the speaker more than the light you say we need a special screwdriver... what special screwdriver... what did you replace??
So much easier to get at the brake light from the top. The brake light housing pops off pretty easily and the light is held in by 2 screws.
Not if you have the bose.
I have Bose and just replaced the 3rd brake light yesterday. But I have the coupe which may be different than the sedan.
@ahighhokie6793 It is, through the trunk on sedan is the only way. Just did mine today also, except I used a $8 autozone running board light instead of an $150 oem replacement😂.
@@drucifer83314 that’s terrible. It was literally a 5 minute job for me. Smart move on the autozone light. I bought a used oem one off eBay for $60.
@@drucifer83314what exactly did you use ? If you didn’t buy an oem brake light mine went out
What special screw driver did you use?
I was able to use a narrow and long phillips screw driver at an angle to get the screw out, but you could also use a right angled phillips screw driver that's shallow enough to tuck in there. Or you could drill a whole in the sheet metal so it lines up with the screw head? Either way, it wasn't a great design...
I took a vice grip and locked in a philipis head drill bit sideways and removred the three screws easily. I then placed a thin blade between the top of the light and spoiler and cut through the two sided tape to free it up. It came out easily. But before doing all of that, make sure that it is not a bad fuse that's causing the light not to work. Total time was about 10 minutes. Removing and about same time to replace,
Where can I find the fuse?
Thanks for adding the video. You skips over the removal and installation parts I needed to see.
The old majestic part number that I bought was P/N 80D0007. It appears this has been replaced with another part (MAJ20308982) but I can't speak to the exact wire and tube configuration.
Thanks for the video! Can you send me a link to the part you purchased? I seem to have bought the wrong type that doesn't have the S and I wires.
I need to replace the pilot in my majestic fireplace 36BDVRN gas, the procedure is the same?
Adding some notes for the common good. This video is a great example when you have the "Signature Control System" ignition type fireplace (his orange "I" plug) versus the more standard, and much cheaper, ignition wire that is a single (often black) wire with a round tube connector. I ordered a cheaper ~$70-90 version without realizing this and had to return it for a more expense "Signature Control System" compatible version which was more like $160. Lesson learned.
Can you please send me a link to the appropriate product on Amazon? I also ordered the wrong one and need one with the S and I wires.
Great video! My fireplace isn’t working and someone told me it’s because of the fire sensor being too far away. I think ordering a new pilot assembly is the way to go. Did you put the fire barrier wherever it was on the old assembly? Secondly, do you know what fire resistant paint is needed to paint the inside of the fireplace?
Hi Jeff, I did use the fire barrier caulk where it was on the old assembly. As far as paint is concerned you can get some high temp spray paint, although I'm not sure I used it when I installed the new pilot assembly.
@@rushtactics1135 thank you for the reply! I found a place where they sell this assembly but the sensor looks to be exact same. I’m wondering even changing it out will help :(
I am curious about the pilot light... after the burner is lit... should pilot assembly pilot light turn off or does it remain lit during the entire time the fireplace is burning..? I'm having an issue and am trying to troubleshoot.
The pilot should remain lit the entire time the burner is lit.
I was hoping to see how you reconnected the GAS line on this project. I have yet to pull mine apart and I'm not sure how involved it is and was hoping to watch someone...
At right around the 2 minute mark, the video shows the fitting that needs to be disconnected from the gas valve assembly. A box wrench should work just fine. Important: Just be sure you close the local gas valve to shut off the gas supply before disconnecting this assembly.
@@rushtactics1135 do you need to coat the propane line threads with anything like pipe dope or tape? Thanks
@@jayf803 Its not NPT, rather more like a Swagelok fitting so I don't think PTFE thread sealant is necessary, but a small amount probably couldn't hurt.
@@rushtactics1135 thank you!
Excellent video. Gives me some confidence to fix mine.
I was able to fix my gas logs after watching your video. Thanks so much