- 18
- 385 773
AIVISU
United States
เข้าร่วมเมื่อ 2 ธ.ค. 2019
Thanks!
NO CRANK NO START FIXED BMW 325i 328i 335i 316i 318i 320i 335d 320d 318d 325xi 328xi
click no start fix! how to properly test your starter and battery.
After replacing the battery and starter it still would not start. so i searched on forums for hours and pieced together and idea of how to test your starter and battery while they remain in the car. this saves hours and money wasted on parts that don't need to be replaced.
the verdict: CAS3 module was burnt, and i have also found the culprit! it was my engine to chasis ground cable. it has rotted and broke off so the electrical short took the path of least resistance and blew the little diode in my CAS module.
$100 replacement module from scrap yard
$550 to get someone to write my old CAS info onto the replacement and code it to my car.
codes: terminal 50 A0C101, A0C2 output terminal 50
0:00 - Start
1:23 - Test BMW starter
4:40 - Test CAS module TERMINAL 50
After replacing the battery and starter it still would not start. so i searched on forums for hours and pieced together and idea of how to test your starter and battery while they remain in the car. this saves hours and money wasted on parts that don't need to be replaced.
the verdict: CAS3 module was burnt, and i have also found the culprit! it was my engine to chasis ground cable. it has rotted and broke off so the electrical short took the path of least resistance and blew the little diode in my CAS module.
$100 replacement module from scrap yard
$550 to get someone to write my old CAS info onto the replacement and code it to my car.
codes: terminal 50 A0C101, A0C2 output terminal 50
0:00 - Start
1:23 - Test BMW starter
4:40 - Test CAS module TERMINAL 50
มุมมอง: 148 860
วีดีโอ
gypsy Moth Caterpillars Removal And Control
มุมมอง 8K4 ปีที่แล้ว
gypsy Moth Caterpillars Removal And Control
2006 Land Rover Range Rover sport fuse panel locations and info
มุมมอง 70K4 ปีที่แล้ว
2006 Land Rover Range Rover sport fuse panel locations and info
I got the crank but it didn’t start
Safety skills are zero 😂 Thank you for the video
i've watched enough movies to know that a giant silhouette is going to pass under you then a 100 foot long shark is going to jump out of the water and kill everyone else
Lol it actually did! Turned out to be some dolphins, i could touch them. But i almost needed new underwear after that!
@@aivisu8865 i remember one time i was in Jamaica, we were about half a kilometre out from the shore when i looked behind us and i just see a huge shark silhouette following us for a few seconds. i think it was probably a tiger shark based off of it's shape and size but yeah the thing must have been around 16-17 feet long
thanks for the video. Can i drive the car when it starts without de cas module?
I have a e21
hi i tested the starter like you demonstrated from the plug to the positive terminal in the engine bay. But now if i connect my battery the car has absolutely no power. No lights go on when i connect the battery
Am getting eye drops today 💧👁️
nice, now i know how to hotwire
Thats me when i get an eye drop
That's not how you give eye drops, please watch proper technique videos. What if your cat "gets up" in the plastic bottle with his eye? You're supposed to treat, not injure.
Solid video.
very helpful. thanks
would this work on a 2011 335i?
Yes
@@aivisu8865 i dont see thst green connector. i see an red and white wire # on a white connector
Hola buenas noches que código te daba? Tengo un caso parecido pero no tengo chispa en las bobinas coill
Wow I love your practical works, see most times people tend not to do it right. I find this earlier and I will continue following your encouraging works. This one's a plus.
So chonky I must have 🥹
My wifes 330 having same prob..i put new starter.relay.ignition push switch..nothing.gonna try this.cheers.P
So when doing the starter test if nothing happens and just sparks, no click, starter generally bad?
I had same effect? Does it mean its bad?
Nice to know
I can see that wasn't a straight cut by the nodge it left on top 🤔
No its 100% a straight cut, just the mirror finish the diablo blade leaves makes it look rough. I should have shown a better angle
I want to thank you. Because you are a life save. After many hours of searching for the issues of no cranking and battery terminal changing, it turned out that the white terminal wire prove to me that the starter is good. Here's what occurred next, I cleaned the wiring harnesses and now my BMW beamer starts right up like a champ. Once again, thank you. Andy Grintatelly
That is beautiful Andy! Glad i could help sir! Happy driving.
Andy wich wire did u clean and where
❤❤❤❤❤❤❤❤❤❤
Fuck bmw.
I am having the same issue. I removed the clip, plugged in the copper wire and touched it to the B post and my starter only clicks. Does this mean my starter is shot?
Yes most likely. Even given full 12 volts and just a click means you’re solenoid is gone
When the air suspension fuse doesn't work are the lights off
Esta información vale millones☝️🐱❤️
I LOVE THIS CAT SO MUCH OMG
Thanks so much man I’m testing that first thing tomorrow
No problem, hope it’s an easy fix!
I will be doing this, thanks for the video!
Bra has me dying starting it in drive
The one I’m working on is a hybrid so it has no starter. The hybrid inverter sits on top of engine so I can’t access the injectors or coils to see if they are firing. What’s more is that I can only crank it once to do the check then I will have to wait for 30 minutes to an hour to be able to crank it again one time.
you are the best bro!
Thanks brotha 🤙
I’m working on a X6 active hybrid. Hybrid cars are a bit more tricky. For example if the engine is not able to start it will throw a hybrid code as well. When I press the start button the hybrid battery cranks the engine but does not start then it throws the hybrid code. At the same time scanner throw an immobilizer code (A103). I notice there is no wire on pin 20 of the CAS. I don’t if someone messed with it or that’s how it is supposed to be. Instead the wire coming from the DME is on pin 30 of the CAS.
thanks tested your trick and no start opened up the cas and the board looks like new ive changed the ivm also and battery was on charger. tested all the fuses and all is good. question: is the jump clip suppose to get warm? i flatten a paper clip im guessing its the dreaded starter 05 645ci
2005 BMW E63 NO CRANK NO START NO CLICK A0C2/not present CAS Output, terminal 50 RS would this be the same on a 645ci ?
Americans love wasting things.
Water is an infinite resource…
More like a waste of water
Water is an infinite resource. Dont be afraid
"the shit ain't startin either way u look at it" lmfao
HAHA 😂
i got to comment you did an amazing job straight to the point and good testing
Why does he look so... CUTE N ADORABLEEEEE
No one believes me but since getting my cat, l slightly chipped 2 teeth from CUTENESS overload!!!! ( Doing it now!!!!)😅
I have a e90 and it has a no crank issue. When I start it everything has power except the steering is locked and the wipers go crazy. I also get a code saying P1631 - Theft Deterrent Start Enable Signal Not Correct. I have put a copper cable between pin 21 and 22 on the cas module (what he does in the video) connector and it cranks the starter, so clearly the CAS is receiving power. could it be the DME or would it be the CAS? Or something completely different? Any help appreciated.
Exact same problem here abolsutely no fookin idea haven't been able to life car up to check all the grounds please hit me back if you figured it out would mean so much
@@creambeam445 will do bro I’m still stuck 6 months later
Awwwwwww
I'm in love
You got the like by trying to crank it in gear lmfao but didn't know that, thanks man!
😂😂
Good video. Nice that you showed where the correct wires are. Of course a already replaced my starter motor, and just about every other damn thing on the car its an N54 335I E92.
Thanks man
That's actually super glue guys
ممنونم ازت مهربون 🥰
خدایا این چه نازه😍الهی قربونش برم من🥰😘
I got the code p16c1 and p1434 what are they if anything knows car cranks but isent starting
Could u tell me which fuse is for the daytime running lights