- 25
- 145 083
Ignorant Custom Garage
Canada
เข้าร่วมเมื่อ 7 ก.ย. 2019
**DISCLAIMER** Any mechanical or technical explanation videos are not how to videos, they're HOW I videos. Meaning that's how I completed the job. I am not responsible for any damage you cause or incur. Always take your property to a licensed and certified mechanic or technician.
After years of modding a friend convinced me to start uploading some youtube videos. The videos will probably be basic as I'm not a computer guy. Will mainly be motorcycle related content. Might do a few riding videos. Don't expect weekly content as motorcycling in Canada is seasonal.
After years of modding a friend convinced me to start uploading some youtube videos. The videos will probably be basic as I'm not a computer guy. Will mainly be motorcycle related content. Might do a few riding videos. Don't expect weekly content as motorcycling in Canada is seasonal.
How I plugged my motorcycle tire
I knew I picked up a nail in my tire on a ride. Luckily I wasn't far from home. On longer rides I usually take a plug kit with me just in case. Here's how I plugged my tire so I won't have to tow her to the shop. Remember this is a temporary fix. In no way shape or form should you do any prolonged or fast riding on a motorcycle tire that's been plugged. But if you're in the middle of nowhere this might be an option to consider.
มุมมอง: 98
วีดีโอ
KTM RC8 and BMW S1000RR back at it
มุมมอง 1333 ปีที่แล้ว
On an unknown roads somewhere twisty where the roads snakes get slippery towards the end of the video... #greentapemafia
How I fixed my GE microwave for 65 cents!
มุมมอง 6K3 ปีที่แล้ว
Like always this is not a how to video but a how I video. Always use a licenced and certified technician. My over the stove GE microwave stopped working and this is how I diagnosed and fixed it for the cost of the replacement fuse.
S1000RR and RC8 End of Season Run
มุมมอง 764 ปีที่แล้ว
One of the last nice runs as the snow has come and 0*C is a daily occurrence. Looking forward to Spring 2021. This is also my first attempt with video editing, its not horrible, I have the winter to learn. The blurring took forever which is why #greentapemafia will exist again come spring
RC8 and Panigale fall run
มุมมอง 764 ปีที่แล้ว
20*C??? in NOVEMBER? Ride??!! Don't mind if we do! Just a couple vtwins in the twisties! #greentapemafia represent
Fall Ride 2020 KTM RC8
มุมมอง 914 ปีที่แล้ว
Winter is coming... as some of the #greentapemafia is starting to put their bikes to bed for the coming winter theres still a few 18*C days to come. It was windy as hell out but nice enough to discover new twistys (kind of) google maps made this road look a lot more twisty than it was, sadly this was the only good bits.
Test run with wind mic
มุมมอง 224 ปีที่แล้ว
Just a quick test run with a wind mic I bought for the camera, is the sound better or worse or the same? Please comment.
KTM RC8 more twisty roads
มุมมอง 854 ปีที่แล้ว
Another video shot the same group ride, we had some on/off rain and some new roads. Again the mic is bad so the sound isn't the best. It'll get sorted out before the Dragon trip :) #greentapemafia
KTM RC8 twistys
มุมมอง 734 ปีที่แล้ว
Trying out a camera position and mount, things I learned, the position is decent but the sound is horrible, I need to come up with some type of mic muff or just play music overtop of the video. More fine tuning is definitely required. #greentapemafia
BMW S1000RR twisty roads #2 with arrow exhaust
มุมมอง 384 ปีที่แล้ว
This is the second part of the run filmed on a private road in the European Union. This video has been cropped for obvious reasons. Arrow exhaust. Testing a higher quality video also.
BMW S1000RR twisty roads #1 with arrow exhaust
มุมมอง 714 ปีที่แล้ว
This video is from a friends GoPro as we did some riding on a private closed road in the European union. Testing/trying a cropping video technique and new video program. Arrow exhaust. Comment on what programs you use as this was not user friendly enough for me. Stay Ignorant my friends.
DRZ Headlight Swap/Install
มุมมอง 4.7K4 ปีที่แล้ว
Hey all, I swapped out my stock DRZ headlight for an aftermarket LED headlight. This was my process. Sorry for the lack of videos as my crappy movie maker stopped working and I'm now learning how to use a new movie maker. Props to the people that do this for a living cause its complicated. (for me)
Suzuki DRZ 400 SM Oil Change
มุมมอง 1644 ปีที่แล้ว
Yet another DRZ Oil change video. There are many out there but who knows maybe mine will help someone out at some point.
Lennox Elite Furnace Troubleshooting Fixed my Furnace for $1!!!
มุมมอง 90K4 ปีที่แล้ว
Always use a licenced and certified technician This is not a how to video its a how I video My furnace wasn't staying lit, it would attempt to start going through the opening cycle 3 times before shutting down. Red and Green fast flashing lights as an error code. This is how I fixed it and saved some money. I'll need to replace the flame sensor but this simple trick saved me from a freezing col...
Changing a 2018 Ram Tail light
มุมมอง 4.8K4 ปีที่แล้ว
This is how to Change a 2018 Dodge Ram Tail light. The only tool you will need is a 25mm Torx.
KTM RC8 Evotech clear clutch cover and pressure plate install
มุมมอง 14K5 ปีที่แล้ว
KTM RC8 Evotech clear clutch cover and pressure plate install
KTM RC8 Evotech clear clutch and pressure plate start up
มุมมอง 4K5 ปีที่แล้ว
KTM RC8 Evotech clear clutch and pressure plate start up
KTM RC8 Evotech Clear clutch cover and pressure plate Unboxing
มุมมอง 1.1K5 ปีที่แล้ว
KTM RC8 Evotech Clear clutch cover and pressure plate Unboxing
Thank you so much.. this video saved me at 11 pm last night when house got under 58 degrees
Thank you my friend, i am collecting my rc8 next week, had an rc8r 2009 , 7 years ago but was sadly stolen in Manchester UK. Im picking up a non r as the Rs are getting rarer and very expensive to pick up here in the UK. Ive jumped in quick after hearing the struggles ktm are having financially and in case the prices go even higher. Ill watch your videos as im clueless on any of the servicing hahaha. Respect and ride safe from the UK
Nice video👍🫡
Nice job but i would appreciate that u showed us the gasket on the new clutch window before installing sir.
Ok. But what's the reason this fuse has blown ????
Thank you Love ❤ We were freezing 😂
Thanks easy fix so easy i did it with one arm just had surgery for torn labrum👍🏾👍🏾
I just did it and it works it really works 😂 thanks brother much appreciated
Thank you for the $1 saving video. I fixed my furnace in less than 15 minutes following your instructions. God Bless You!
I have this same furnace with the same issue and cleaning that flame sensor did the trick. I’m a new home owner and always looking for ways I can same money and DIY. Thank you so much for this content.
Thank you so much this did the trick and you’re right… this literally happened on a 20 degree Sunday Morning when I’m due to go away for work for a couple days.
Totally worked for on a cold Sunday! It cost me $20 because that’s all I had in my wallet, but still the best video on TH-cam!!!! Thanks!
Ty buddy. mine went out around midnight. diddnt know what to do last night. but woke up on a mission to figure it out. watched your video. and it worked. ty so much.
It is Friday 7PM. Just find out my furnace is working right. The same problem like yours. Fixed it...!!! Tanks soooooooo very much.
Thank you for this video! Like you said, it's a Friday night on a holiday weekend. 26 degrees F below zero and getting colder. My heater: "Goodbye Cruel World." We're back up and running after cleaning the sensor.
Whew, That was bitter cold and I worried as well. My Lennox is slightly different and running on L.P. and I haven't had it checked since installed in this old farm house on 11-2019. Works like a champ but when it's bitter cold an old guy on the farm can worry. My furnace place said they sell Lennox cause they are most reliable. Finally going to warm back up but it was 7* below zero near Battle Creek, Mi. this morning. I will stop in this week and buy that sensor and probably ignitor to install and keep old ones as spares.
Cool. Couple of tips for others: Tie the lever closed when disconnecting line- no fluid can escape the hose as you work. Also, when connecting hose, get the crush washers kind of tight, squeeze some fluid (trapped air) thru the washer/ fitting assembly then torque it to spec. Once finished, tie the lever half closed to allow any air to surface over time. All this is most important with (good) brakes. Ordered my Oberon, just prepping. Thanks!
You never explained the flashing light code????
The inside of your panel will tell you what the lights mean, all HVAC systems have a legend
Anyone know how to replace the filter on these things? I have the same furnace, but the air intake is different. In this video you can see the filter box set on the floor to the left of the furnace. My air intake does not come from the left, but from the bottom. I opened it up and did not see a 3M square filters nor a larger box filter unit between the air intake and the cylindrical fan towards the bottom. I am starting to think that I might need a tech for this one.
Make a small video of the unit
Couldnt see anything your doing
Sounds like you should definitely call an HVAC technician
Fixed my issue. Thank you so much. Saved me from an incoming winter storm and the thanksgiving week.
I had the same issue. I ordered the flame sensor but the wrong one arrived in the mail. I sanded the metal sooty part with 500 grit paper and wiped it off. Furnace works perfectly now
lifesaver here thanks buddy
Thanks for your "how I" video. You're a genius!
10Nm sir for the slave.
What is the headlight from
Amazon, it's a replacement bulb for a van
By any chance have you had a chance to upgrade your thermostat to a new smart one like Wyze, Google, etc. Wondering if you have instructions for it with this Lennox Elite unit.
I don't and I'm not a fan of "smart" anything inside a house
Thank you man you were right they did come over charge me 212 and they didn’t fix it I did what you said and it works thank you so much for the idea really thank you a whole lot and god bless you for your videos
Thank you soooo much it was so easy to fix.
I clean mine once a year with fine steel wool, no problems since. Also make sure you change your furnace filters often. If we get very cold weather and my filter is not clean, the heat exchanger sensor will shut the burners off until the furnace cools down.
This video saved my ass for a second time tonight. Really a blessing video. I have a wife and two babies here on this Saturday night at 1030pm. Much love thanks again
Much appreciation to you sir for posting this video. Worked like a charm! You have saved countless men money and some semblance of their manhood as well.
Do you just take it to a regular tire shop for them to patch it ?
Absolutely not! This is an emergency plug. I plugged the tire so that it wouldn't flatten to the rim and also for ease of loading onto a trailer should it need. Never ride on a plug unless absolutely necessary.
I just did this and it fixed mine!!! Thank you!!!
Very informative video, thank you. We use to have an old Rheem gas furnace, and the repairman did the same thing. Only he used a small ribbon of 2500 grit sandpaper. We now have a Lennox furnace just like the one in this video, and it started acting up last night. Did the same thing in the video and it now runs like a champ.
I just did this little trick, and it works! My furnace was intermittently not starting. I did exactly what he said to do, I cleaned off the flame sensor. Now it’s working wonderfully! Thank you.
Just wanted to ThankYou for this informitive video. I had a different furnace but, found the sensor and the fix worked perfectly. It was a Sunday afternoon and these things never go out during normal working hours. Mucho money & time savings. You are a friend of mine. Thanks Again. Best Regards, TJ
Thanks 🙏 it incredibly worked! Appreciate you brother
Excellent video my brother. Fixed mine this morning thanks to your video👍👍👍👍. Took 5 minutes
My whole family is very grateful fot this video! Saved us from cold weekend nights and saved us money, and it was a huge blessing since we are currently unemployed. Thanks again!
Thanks you Sir. My Lennox system did the same thing yours did tried to ignite 3 times and then would shutdown for a few minutes to clear the gas. After a few attempts it would go into a lock down. I cleaned the flame sensor which was located different than your furnace and was L shaped at the end but after watching your video had no trouble locating it. I cleaned it with a $1 bill just as you did put it back in and heat is on. You saved me some big bucks because it's a Friday night around 5 p.m. when I got home. My furnace was giving a code the red light would flash 8 times then pause and flash 8 times and pause continuously. Now I know. Thanks a bunch!
I consider myself a basic handy guy and the furnace is always seems intimidating. Your video helped me save some $$, a warm house, and a happy wife! 👍
Thank you so much it worked like a charm 👏🏻
Thanks 👍
My furnace quit last night. However I've had this issue before. Check your intake pipe outside. On cold ,windy, snowy days this pipe may plug up. Just clear it with some type of wire and it should start up. This may or may not be your issue but before calling a technician go outside and check the intake. Merry warm Christmas to all.
Dude, you wanna really know why this video was perfect? Today, Dec. 23, 2022, in SE Wisconsin it was -10° at 6 am and yes, No Heat in the house. Fortunately, I have the exact same furnace and mine was doing the same thing. Super easy to fix and 10 min later, my house is warming again. Thank you.
Much love mine just went off on the middle of night its a -8F I had to fix it seen this video and I tried it and it work
Thank you for making this video! Saved my family and I from the cold tonight as well as a few hundred dollars 2days before Christmas. You're the man!!!
It's wise to buy an extra flame ignitor in case the ignitor goes bad.
Completely agree, also a flame sensor but keep the current one as a back up
The cleaning of the flame sensor should be done every year.
So it's currently 17 degrees in texas today. I was having this same issue, looked at your video and it got me working again. Thanks so much for this post. Worked like a charm!
That's cold for Texas! I didn't think it ever got that cold. Hell I didn't think people in Texas had furnaces!