วีดีโอ

Hello, "Nifty : Nissan & Infiniti HOW TO'S" I was analyzing your channel and saw that in your channel have some problem, That's why your channnel is not much growing and not getting much engagement, If you can solve these problems, Your channel will grow like a storm. If you tell I can tell these problems. Where can I tell? Here or email?

Let a pipe fitter or plumber in there 🍻 My ridgid pipe wrench says goodnight

How to fix code P0507 or P1815

It’s Nissan what do you expect its junk?

I had two p0420 codes. I changed the o2 sensors and replaced the cats yet the code was still persistent. I changed my ecu and then the codes went away thankfully

first to comment 👋

thank u for ur videos bro💯🙏

where can i get the gallery gaskets you guys use or are they the ones that z1 sells?

Can I use these same steps on an sedan

Mandatory resonator box scrapes can't escape them

not very helpful

Can u make a video on these 2 codes plz? P2A00 and P2A03 and I’ve already replaced the o2 sensors but the code is still there

hi, i have a 2008 g35 sedan. can this fit it?

No hate here but homie that tape ain't going to work the heater circuit pulls enough current that it's going to basically perform electrolysis the first time it gets wet and become green and rotted and corroded way better off if you're wanting to use butt connectors use the actual heat shrink ones and the correct cramps or my personal favorite Scrabble soldering iron and a piece of heat shrink tubing literally the fastest best way is solder

Will replacing the ignition cylinder allow for you to start the car or do you need to program it still

You can take the strut out with just disconnecting the upper control arm from the knuckle and pushing down on the rotor

W post fr and they got Christian heat boomin🙏✝️

Lol u did too much bro i got a better way nobody wants to do all that

Me wathcing him not tape the clockspring while trying to remove it 😰

Thanks for these. I have a G37 and TH-cam videos like this have saved me tons in the last 12 years on my car and my wife's 09 Pathfinder.

Have y’all done a head gasket video already?

I spotted that Z trans in the first second of this clip!

Isn't there usually a silicone gasket between the MAF sensor and the orifice it sits in?

Could you please do a engine removal for a vq35hr in a v36 sedan

Nice vid man. You're a good teacher.

What if I hear that clunking sound in the rear ?

Great explanation, quick and to the point. That’s what I love to see on here. Well done.

Terrible wind noises with osmo sheesh. I’m getting the dji ones

I been sitting on this roll of wrap until I seen that you guys dropped the channel. These videos have been a big help fr.

I know this video is hella old but I have a question with the draining process. I drained all the coolant out of the radiator but there’s still coolant in the reservoir, do I leave it in the and just let it mix when the engine is turned on or take the thing off and drain it separately?

Worst fucken headlights ive dealt with in a car, 3 years with this car and ive tried countless times and its just stuck

would megan racing y pipe fit this

do you have to take the engine apart to remove the transmission ?

Great video. I did this job a few years ago on a g37x. Now I am working on a 2015 q50, driver's side rear door and struggling to get the door open. I was able to remove the door panel (I'm shocked) but still wrestling with getting the old actuator to release. Do you have any tips on how to do this? Once I get the door open I think I can get it from there. Appreciate any advice. Vinny E

Need a alignment video

That RTV application was hard to watch.

Better gas mileage not so much when everyone with test pipes is using some sort of pop tune dumping fuel

All you had to do was just turn the front wheel outward. No need to take it off.

Why are you doing all the work of taking the brakes off and pulling the front off. So much extra work for a strut video

forget even looking at woodruff key, the line in crank gear and dimple on block where orange link is is the reference point for the bottom

thanks for the help

Nice work. Thanks for posting!

Wonderfull resource of VQ how to videos, got my gallery gaskets done with help of this.

8:12 If you leave in place this 10mm bolt and dust cover at the bottom of the engine, will it stop the transmission from coming out? I'm struggling to remove an engine with the box left in-situ. I removed that 10mm bolt, but it looked like it only screwed into the engine block, so I put it back in. If I remove it again, will I suddenly find the engine comes free? :D PS, This is a great tutorial video and deserves more views! I love that you showed everything, and didn't leave out bits, or fast-forward them.

Is it the same also for a m37 ?

nifty how to do a vr30 trans swap on G/Z | Complete DIY Guide.

Thanks for video bro, this is great and helps out alot

Thanks very helpful

This video is an ABSOLUTE God send! Raw and unfiltered and is EASY to understand! THANK YOU!

Please make g37 manual swap