วีดีโอ

From memory when charging they flash in a sequence and when full they are all solid. It's only blue, no other colour

@ looks like mine go full blue but the power switch is dead..back to Anaconda!

@jonathanisles Interesting. If you double tap or hold the power button it doesn't do anything?

@@geekydad8565 nothing at all, taken battery out, (blew on it!), put it back. Initial charging produced some heat over the battery, but then Watts draw went down to 1-2W, suggesting fully charged. Still no lights. It seems that it came fully charged, which is hard to believe, so maybe I just have to leave it for 3-4 hrs and see what happens.

After 1 hrs on charger, started constantly beeping and bottom 2 blue lights flashing with third intermittently flashing, but no further progress after 4 hrs. Still will not turn on. Anaconda happily took it back for their bloke to test on Monday, and said they’d had quite a few coming back with issues, mostly related to faulty charging. I’ll see what comes of this, and let you know.

I'll have to see what I can do in a week or so. A lil crazy right now in the holidays.

I wouldn't since it's not intended for that

Thanks for the feedback. My TH-cam journey is somewhat amateur but I'll keep that in mind for future videos. Maybe if I have time I'll edit this one too

Shows bullseye later? Maybe that's a mistake I made?? At the time of recording bullseye was not compatible with pibooth. With version 3 out now it does now although I have never tried it. If you're using version 3 it will be best to follow the instructions on the pibooth website. documentation.pibooth.org/en/3.x/sources/install.html

Thank you. I share for that very reason. They are Dupont jumper wires. I bought a pack from eBay a long time ago. Just look at what you need in terms of the connectors ie male or female on each end

@@geekydad8565 ohhh! to be honest i got a bit confused because i saw the dupont connector but then spade on the other side. so the spade connectors that you used for the ground cabling would have been spade to female dupont with the dupont side snipped? is that right? what about those chunky connectors on the neon pix ring? i am thinking of skippoing the neon ring altogether but in case i decide to use it... what are those called?

@Rafa.T. oh right. The spades I had laying around and you're correct. I just cut the wire and soldered it on. The chunky ones on the ring I got in a set that came with a wire stripper. It's not required, you could just go without the connector or find some other random type of connector if you needed something

@geekydad8565 nice nice thank you! I already got it working on pi 3 such a fun little project. The kids will love it. Thanks again for the video and the responses ♥️

@Rafa.T. Too easy. Glad it spawned other family projects!

It shouldn't do this at all unless a seal is broken. Recommend you get a refund

Sorry just worked this out - its do do with setting "upper" and "lower" limits. When in normal working mode pres and hold the UP key for 5 seconds and you can then go in to the mode to se the upper limit for temperature. To set the lower limit press and hold DOWN for 5 seconds to go in to the mode to set the lower limit . When in each mode use up adn down to set the limit then press save to save them

Happy birthday! You're very welcome. Enjoy your new toy

That was actually a Sunlu Grey. Bambu was out of stock for a while after a sale. I quite like their shade

@@geekydad8565 Looks very close to the color Bambu uses on the A1 top corner posts.

Yeah it's not far off. I do like it. The Bambu one from memory is slightly lighter

I read this comment with tired eyes and had the image of a stone with eyes

Sorry can you please rephrase your question, I do not understand

hello, the qr code is very large on the screen and mine is very small

Does the QR code work for you even though it is small? Originally the QR code is small but it didn't work until I configured it to use the dropbox URL. The longer the URL the bigger the QR code. Also the smaller the screen and higher the resolution setting the smaller everything will be on your display. What size screen and what resolution are you using?

Hi, it's not available as a standard. It could be a feature request you can make on their git or try develop yourself a plugin

Hi, it's all in makerworld. Links are in the description for each print. Enjoy!!

For button 1 and 2 you need a cable for each going to the ground pin on the pi. Physical number of the pin is 6. Its the 4th down on the outer edge of the board. The remaining cable for button 1 goes to GPIO pin 17 (phys number 11 or the 6th down of the inner row) and the remaining cable for button 2 goes to GPIO pin 27 (phys number 13 or the 7th pin down from the inner row). Here is another diagram with the pin outs that may paint a better picture. pinout.xyz/

They work by default without added config. What's happening on your end to try to help you out? Make sure the wiring is correct as per the diagram here documentation.pibooth.org/en/stable/sources/install.html#circuit-diagram

For the two front buttons I didn't need to. They work out of the box. You'll just need to be sure you wire it up correctly like in the diagram. Unless you're talking about the power button?

@@TheAirSit for the power button its in the boot config file. I have the command in the video description too if you haven't seen it

Hi, if you're asking about the wiring here is a circuit diagram which may help. documentation.pibooth.org/en/stable/sources/install.html#circuit-diagram. Can you please give me more detail on what you mean by config? Works out of the box so you shouldn't need any

My pleasure. Glad I could help. Enjoy your new prints

Hi. Yes it's powered from the printer. I bought a micro-fit 3.0 cable from aliexpress and wired it to a DC 24v to 3A 5v USB board. Works well

Hi, if you mean the stabiliser legs at the back that was with sunlu grey PLA. Let me know if you meant another part

That was it, ty man!

Little off, not horrible

Yeah you're not wrong. My mic has been playing up. Sometimes it works and other times it doesn't. Need to find time to fix it up

@geekydad8565 All in all, ​a good preview from a beginner to other beginners. Weird audio in the beginning, but still very valuable information. I should get my A1 in a matter of days, so : Thanks a lot. Keep us posted. 😉

@sebastienquere7566 and thank you so much for your support!

It was some time back. I was mixing it in a 1 litre bottle and kept measuring it until it was around 35 ppt so I don't have a mixture I'm afraid

@@geekydad8565 tq for your reply. Approximately how many teaspoon or tablespoon for that 1 aquarium?

I can't say I'm sorry. I didn't keep track that way

Possibly but not sure of what things you may need to overcome (if any). Doing a quick Google search, someone online claims they have done it for themselves too.

@@geekydad8565will dive into this thanks mate !

You are very welcome. Thank you for your support!

@@geekydad8565 I am currently in the process of rebuilding a photo booth, but at the moment I'm having issues with the Raspberry Pi. When I start Pibooth, a small window opens, but then the program crashes. I'm not sure what's causing this problem or how to fix it.

@ElfenBoss18 if you run the pibooth command from s terminal you'll at least get errors from there. If you rely on the auto startup then it will disappear. In my case the errors usually relate to the camera not being detected on startup. Let us know how you go

@@geekydad8565 Hello ; ) I managed to get it to start, I had a Raspberry 4 and there were complications that I fixed ;) now I have to get the QR code and upload the photo

@christophernowack4971 great progress. Sorry I couldn't help there. At the time i set mine up the pi4 was not compatible

Thank you! Definitely not a rechargable battery that comes with it. Mine is still going strong since I uploaded the video. It's been telling me that I still need to replace the battery and funny enough I checked it about 30 mins before your messaged. i am currently parked in a back street that I've never been before and I'm sure I'll get lost haha. Very simple and cheap to bring some life back to the unit.

Eeek..i can't remember. I was bulding this with my kids so I had to go slow and it was my first time using a table saw. A lot of start and stop and trial and error. It was no weekend project! Take the box out of it and the rest can be done in hours

I haven't come across a reset option I'm afraid

Great idea and congrats for the upcoming nuptials

Enjoy. Mine had a lot of use. It's been great. Don't do what I did and put boiling water in it. Recently the plastic cracked from the heat. I'll be buying another one soon 😢. I'll make sure the water has cooled a bit after boiling next time.

The instructions start on page 2, BUTTON OPERATING INSTRUCTIONS...Everybody missed them...

Lol similar thought was in my head when I was scrolling through potential prints when I first got the A1. It was a quick one to do and my first which was multicolor so I said.. What the hay...Don't think I'll need it really. I do have a cat who may want to run some jobs without permission so that will stop her, other that that, any accidental spills or drops 'could' protect it. For others with kids about or where their printer is in a high movement area it could be valuable.

Gotta give a tip of the hat to the designers there

While it can power the lights, too many running at it's highest brightness can damage the board. I can't remember the safe number others have calculated online on how many LEDs you can drive but 16 was too many in my case

I did mine via usb. FYI Pibooth won't run if you don't have a camera connected to it when it starts unless you have a plugin installed for debugging that pretends there is a camera active. Might be the reason why you are having issue. I think this is a compatible list that I just googled. The DSLR needs to be compatible with gphoto2. gphoto.org/proj/libgphoto2/support.php

I haven't come across this error but if you're using the DSLR you need to add an extra variable during installation for DLSR specifically. Not sure what else it may be otherwise. Maybe not a supported model???