วีดีโอ

Fibre glassing is a bit like plastering, once you've mixed it you're fully committed, not sure I could handle the pressure! great job, great vid👍

Cool Job and you put a casting deak on the front?? I think they would sell well with the hatchs in the front for storage all so the latrex 335 i was looking at but no deck or hatch in the front

How much did each material cost

"Buy or rent a mold" ??? I've looked for mold rental businesses in my mountain city. I find only mold removal businesses.

Anyone watching can instantly tell, inspecting the mould, carefully cleaning it, allowing it to dry, finding and taping the imperfections, waxing it …..took way more then ten minutes and that was just the prep! Then you have to fibreglass it, carefully resin or epoxy it and wait at least a few hours for it to set up! I have done fibre glass setup work and impossible to do it in “ ten minutes”!! What a load of malarkey!!

2 x 1200 hv

very nicely explained. Very technical which I appreciated.

Engine size at the end😂😂

Cigarette 42X "No Xcuses"🤩

Awful music, and an equally awful power package

Why’d you play music over top of that awesome video?

Where do you buy or rent pre-made boat mold?

Damn i want one

Tax dollars hard at work 😂😂😂

I would have gone for triple 500hp motors.

I am sorry but your pronunciation is hard to understand in English. Did you say ( you must also check that you don’t make too light bracket because the water rises up from the boat bottom also there .. ? ). If that’s not exactly what you said. Please correct me if I’m wrong. ======= > it is said near 4:04 minutes of video.

Oxe

I don't see oar locks or a transom for a motor. How much does the material cost.

Yamaha on paras kaikista moottoreiata

nice

I know nothing about boats. Is a v8 good for a boat😭

Evinrude E-tec. 😬 mahtookohan rantautua suomen kamaralle näitä brp rotax koneita?

Mercury vaikka itelläni onkin honda😂

Honda

Looks like you bought a figerglass boat added a few more layers and mods. I didn' t see a boat being built SMH.

Thanks, I really enjoyed watching

Nice work. Can't wait to see it with the engine for the test run.

so this thing actually took you several hours it's just standard glass layup -- So what ?

350 v8 on that thing? 🤣 why not use 2?

Kyllä katamaraaneissa vaan on sitä jotain, mutta 2:04 nurkilla olevan veneen eleetön kulku on hienon näköistä myös.

Hienoin oli se 1 min 30 sek kohdan fountain mikälie ja parhaiten taisi uida kuin juna raiteillaan tuo vene #43 2 min kohdalla. Ottaisin kyllä jälkimmäisen jos pitäisi mennä kovassa merenkäynnissä.

When this thing came out, there was nothing that could respond to it. The 250s and 300s offered an almost perfect symbiosis of 2 stroke and 4 stroke benefits with almost none of the drawbacks of either. What a letdown and mistake the g2 was

Wow

That looks just like peggies apache but his had blue letters for apache

Do you have a list of tool to do this job think long about to try this on a free boat I got ?

Very useful video! I am looking to convert my 1995 Bayliner Ciera 2655. It has a V8 260hp inboard engine, and I fear it will start falling apart and cause a lot of costs. However, I will not put anything bigger than a 30hp outboard on the bracket. Do you think it´s possible to mount a bracket under the swim platform and bolt it to the platform? I could initially leave the old drive shaft there and deal with that in the winter.

3 for sound

One dollar Bob

I feel bad for whoever has to work on those.

🔥🔥🔥

Kyllä eemelin vehkeille on ihmettelijöitä

how did you blue the two edges of fiberclass between the mold and the one in the boat ? I am kinda worried about this bond, even after laminating figerglass from the bottom of the boat and inside the boat. I'm having to do the same on my boat, but I am extending only 6 inches long. would you give me some hints ? I will be using polyester resin , plywood for the transom and fabric for the hull.

Taitaa olla Saimaan nopein vene. Sadan solmun raja meni rikki toukokuussa. Kesällä 2023 kopassa luki vielä 250R, joten silläkin lienee osuutta asiaan 😉 Imatran vauhtivene-expertti Eemeli Nenonen on muokannut Twisteristä todella upean ”daycruiser-katin”, joka toimii hyvin retkiveneenäkin. Ehtii sadetta pakoon tarvittaessa varsin ripeästi 😉

Someone needs to buy them out and bring back the Gen1. They were awesome outboards.

2 x 1200hp

What about Gen 2 300hp those any good

Mörkö! 🤌🏻

Tell me the true Cubic inches and if they are Supercharged but just by the sound they are Big Blocks with Race cams so between 800 and 1000 Horsepower each. 1600 to 2000 total.

165

Do they care about climate change?😅