วีดีโอ

Excellent, just plain awesome job man! You didn’t cut any corners at prepping the area. It paid off. Amazing good looking land area you two have, congrats are in order….would love to play some pickleball games with you guys….go Sweden 🇸🇪! Cheers from NYC 🗽

Hey thanks, my 3032e has the exact same setup and I've noticed its been going too far up and causing strain on the hydraulics, and it immediately starts to drop the second move the lever off 9. My sensing valve was stuck and binding up. I loosened both bolts, sprayed it with penetrating oil and started working it loose. Its still a little tough to move by hand so I'll keep working on it, but for now its ok. Much appreciated on the video!

Those ghost stories boutta be insane 😂

I really need a video that shows how to fold this umbrella. I saw in my instructions the tension clip you pinch/squeeze but I can't seem to make that work.

We're going there in August.. wanted to see the village thanks

Cheaper to just purchase new one then do all that 4 sho. I guarantee 🤷🏻‍♂️

Thank you so much. Was long but you showed me all the struggles and how to get it. Now to do mine. Thank you again so helpful!

How many hours do you run after every change?

I followed step by step and I went to turn my zero turn on and it moves now back and forward but now my blades don’t engage need halo what can I do

Hello I would like to know how I can get the front bumper and the front cover

This was a very, very helpful video. I did the same repair on my JD Z525e last week. Pretty much the same "anatomy" on both machines with a few small differences. I found it easier to entirely remove the mower deck though. However, I made a rookie mistake, sort of. I completed the whole belt replacement and I also replaced one of the pulleys that was damaged (I must have caught a small branch or stone or something at some point). Anyway, got everything put back together, tested it and the clutch/transmission...whatever...wouldn't engage and I still couldn't move forward or in reverse. No dice. I did a close inspection of my work and everything seemed ok. I took pics of the layout before I started to take things apart so I was pretty confident. Still couldn't figure it out. So I called a mower repair guy I like a lot but he couldn't get here til tomorrow. I was thinking maybe one or both of the transmissions failed somehow which would cost about $1,000 each just for the parts if they needed replacing. I even began to look at new machines. But I went out about an hour ago to take another look and I suddenly realized I never re-engaged the two levers I had disengaged to release the clutch (or whatever) that allows you to easily push the mower! I re-engaged them and BINGO....back in business. Thanks again!

I'll continue to use my power scythe.

Yeah, to hell with the instructions. Instead of cutting the nozzle to apply, just unscrew the cap and waste a whole bunch of it. And use whatever you want to apply it, forget the demo.

thank you

Great repair. Definitely some hard work done. I have an exmark with a V twin Kawasaki. How hard would it be to take the exhaust off on the mower?? Got some welding on the muffler that I have to do it and don't want to fry any of the electronic parts.

How thin did you make this paint?

You didn't set the pads before adjusting. You tightened the castle nut to tight. You adjusted the pads to tight. You didn't score the drums enough. To your credit you did do a good cleaning of the parts.

Z Ño

YOU are Omazing ! Exactly what I need to do in my new home. Looks sooo good! Your home is gorgeous😇

Very thorough review. Thank you

Great video thank u saved me some money

Thanks for posting

That was Awesome 👌

What position should the hydraulic release levers be in when they are not needed

Aya man.... i understood we all wash our hands after doing a job. But this is pretty disgusting mate 🤢🤮🤣.... I appreciate the review but sheesh man.

My bush hog won’t drop. I’ve checked the speed adjustment and it’s still stuck. Any suggestions as to next step?

👍 the trimmed off pieces make perfect hunting blinds 🫡

That is obviously a tensioner assembly (the giant spring tension is a clue) not an idler.

There's a hole right above the idle jet that you can put your screwdriver to get to get the screw out without taking the stepper motor off. Also never start or shut off an inverter generator with anything plugged into it

Use magnets to keep the curtains vertical gap small.

My belt broke today. Great video. Much better than the “Operators Manual” instructions. Thanks for making the video.

The reviews of this asphalt paint are not too good... lots of people complaining that it fades significantly after about one year. Have you noticed any fading? Will you need to reapply soon?

Also sanitize the needles after poking them eggs. No cross contamination.

I bought this egg cooker. Works well. Advice: poke holes in the LARGE end and place in carrier SMALL end down. The air bubble in the egg is at the large end. Releases the air and makes them very easy to peel. I leave my eggs in the tray for a few minutes after the timer goes off. No could water. Cooks then egg more to myself liking.😊

Thanks

Fantastic suggestion!!! We live on a farm also. We bought a stick at our local store and cleaned around the sink and toilet and now our bathroom sparkles! We did not use it on the shower surround as its plastic - but the ceramic sink and toilet look amazing. We also used it on grout and caulking that had become dark - we may need to re caulk but - so what. Great results!!! Thank you so much XXXOOO

The first half of this video is "Pressure washing a cement slab". Skip to 3:12 to bypass all of this.

Very well explained, thanks

Any ideas why mine isn’t zapping?

This was a great video and thank you for making it. Also nice that this was the actual belt video I was looking for. A lot were called the traction drive belt but were actually showing the mower deck belt, much appreciated!

My belt came off because an idle was loose. The part where you tell us how to use a ratchet and extension to move the idler saved so much frustration. Thanks for the great video.

Frustrated! Any idea why the two long vertical pieces on the sides of each unit and not straight? What do you recommend doing?

The screw is too short for me

I assume that like other lithium batteries, if they go too low the charger won't recognize it. Is there anyone confortable enough with the device as to where I might give it a bump from another 12 volt device?

Hi, I have an he same generator as you, I follow the steps you did and I did get the generator to start, it runs like a champ, but another issues issue as I start the generator it powers up the green light comes on for about a second or two then goes out and then the trouble light comes on and it just flashes the green light never comes back on, do you have any idea what I can do next, please help

Works better with a card or plastic putty knife. The paint brush just brushes it all away 🌬️

I luv the Crocs 🐊 😂

Great Video!

did the same job but i was wondering about the retraining "C" clip on the RC2060 shaft . thanks

It was a good video but it was still a pain in my butt to do it all lol