วีดีโอ

05 Dodge stratttic goes into gear but doesn't move just jerks forward?

My car has the same problem during driving on the highway 6 weeks ago i take the turn off and the clutch has no pressure so unable to change gears. Then it went in gear again and no problems until yesterday it came back the same problem unable to shift the gear. And then all of a sudden it was ok again drove to few places car was ok no problem then this morning again the same problem. Is it possible the cylinder could be on its way out or would u think there could be an air pocket inside thats causing the clutch to stop working?

I have an 04 RSX type s. Clutch sticks to the floor unless pulled back up. When driving though it will shift relatively okay with some sticking after driving. I’m torn between slave cylinder or clutch cable. I had the master slave cylinder replaced a few years back. What would you suggest?

I have the same issue, I replaced the slave cylinder and the master cylinder but there’s no pressure, I want to think after bypassing the clutch damper it will help but I’d like some tips if you have any, 1997 hardbody 2.4

My clutch doesn’t stick to the floor it just has no stiffness or pressure to it I replaced my clutch and everything bled my master cylinder and now idk what to do.

I've got a 92 GMC manual,The shifter is floppy,I've replaced the shifter and still nothing. Any ideas anyone would be greatly appreciated

How to fix a clutch master cylinder on a 2004 Dodge Dakota SLT 5 speed 4x4

My clutch is stuck to the floor with a burning smell and screeching noise. Any ideas what that could be?

2005 ford focus

It's 05

1992 chevy k1500 nv4500, changed master and slave cylinder, and clutch kit, throw-out bearing, pilot bushing, flywheel, clutch and pressure plate, blew out 2 slave cylinders, first one split on casing (plastic), the 2nd (Luk) one gave out replaced seals from the plastic one, built pressure, lasted 1 drive then gave out too, haven't seen where it's leaking from yet, any ideas, or any recommendations on a heavy-duty slave cylinder

What's up with the project? I have my 83 up on my channel hoping to get some more content going!

Thank u very informative ❤️🙏🙌

Awesome video

I have a 1994 ford ranger just got a complete rebuild on my transmission but I push the clutch and it starts but it won’t go into gear I need help how do I fix this problem I bleed it everything and nothing

My clutch on my 96 Camaro has no resistance. You can push it to the floor with a finger and it does return. We noticed it leaked fluid when we put more in. It leaked out of the transmission case, just under the flywheel where there are drain holes. Any idea what’s wrong?

I did all this and still have no pressure on my pedal

Dang that's quite the before and after, very nice, glad to see another truck saved and back on the road.

Haven’t drove my 2017 challenger in a month when I charged the battery and started it up the clutch was very soft not normal as it was very stiff only has 33,k

Silver turbo, one of the best looking Z cars ever made. Hope you put her back original.

11 jeep compass clutch is good there was a little air in lines an I tried to get it out an my clutch pedal went away if u pump it like crazy it'll come back next day gone again u know what it could be it was fine up until I loosen the bleeder any tips on how i can get air all the way out an stay out would be much appreciated thanks

Looking forward to this!

I was looking at mazda b2200s and was curious if there’s still places where you can get parts for the trucks. So I am wondering where you got the parts? And if it was hard to find the parts? Because I want a b2200 but if I can get parts for it that would be unfortunate.

What is the problem if I start air Ac the car is low the clutch

My clutch pedal does what yours does but the cylinder doesn’t move, the clutch just goes flat and then comes up again when you pull it but it’s not engaging the clutch, what’s the issue This is on my mg f

I have mazda 3 2014 has the same problem like that I have changed all of those clutch cylinders but no change what might be the problem

Keep them coming bro

مرحبا سموك

Right on, looking forward to the next…

Looking forward to the next video !

Subscribed and will wait for updates! This is sick man!

I have an identical one to get started on when I finish the Defender I'm at now. Well, identical except it's a diesel. I did one before, few years back that had a load of rust - tub was the worst part but the chassis wasn't too sharp either. What I learnt from the last one (plus a load of other restorations I've done on pickups) is don't muck about, take off the tub, pull the motor & tranny, pull the front clip & pull the cab - get it to a bare chassis - or else don't bother starting because you'll only be doing half a job if that. Best of luck with it & they are a cracking little pickup - well worth the work. :-)

Bro im planning to restore same truck. Good luck to us

Um got a question where are you located abouts I have some parts we can send you .

Omg all I can say it good luck bud . I can't wait to see what you can do with that truck

Damn bro, crazy realistic, looks just like the game!

Ouch, she looks rough. Looking forward to see what you can do to it…

Cool!

Great job!