วีดีโอ

Thanks for the nice video, Alec. It helped in my repair of my old Hayter Envoy35 that has virtually the same switch design. I found a similar continuity break at the same point in the supply cable. Quickly mended. Your tip about the internal springs was particularly helpful. You’ve probably saved my quite a few hundred quid for not having to buy a new mower so cheers. Andrew

Hello, thakyou for watching my video. The diameter and the overall length are both critical to it clicking in. Just check that both the flexible plastic catches are intact. Good luck. Alec

Thank you for the share. Nice job

Brilliant, I was struggling with my tractor master cylinder seals, then found your video, the master cylinder is identical mine to my caseih tractor, boom, all sorted now, cheers

Thanks. Changing my rear wiper blade first time. This is helpful.

Thank you

Nice one, looked a bit tricky to me. Thanks for uploading this

You solve my problem thanks

at about @2:10 how does he know that the difference isn't caused by a vacuum leak? because if it was, he just masked it, probably forever.

Upgraded my 1963 TR4 to a CSI unit. Negative earth type as I already made the conversion fron pos earth. Does your car run well with the "9" flashes or have you adjusted after road testing?

Thanks for the video. You showed us how they look after they're taken apart. And you showed us how they look after they're put back together. You neglected to give any advice on how to get them apart. The hint about the rollers was helpful. PS: When I did mine, I put them in my electrolysis tank that I built for removing the rust. Works great, and is less damaging than wirebrushing, since it removes the rust on a molecular level.

Thank you!👍

THANK YOU

A little bit of the best British engineering. Thank for that. Alec

I worked for Girling for 28 years, I probably have the drawings for these, which were made in Cwmbran.

Hi Alec. Just a short note to say thanks for your helpful TR4 videos. They have been invaluable to me and i will be making one of your rear seal removal tools in the near future.

Witch repair kit do you use ? Reference of the repair kit? Nice video i'm from Portugal

tks a lot

@ 0:35 please don't apologise for naming parts...i didn't know them, but thanks to your tutorial i now do! Thank you very much for this

Thanks for the video. Just what I needed. Cheers

Great job.

Thanks for that. Took me ages to work out how to release the spring following the haynes manual

Thank you, it worked. Only difference is that I held the nut is a short section of split cable wrap an some electrical tape to firm it in place. My wife held it whilst I rotated the nozzle.

Hi Alec, How to Differentiate Right and Left Trunnion Physically?it seem to be the same ?i have got a pair of new one but i don't see

Thanks, great solution!

Hi, wat is this part called? I lost this piss in the move and I’m trying to find a replacement

It takes a 1616 3v lithium battery. Thats for an 06 year Jazz.

you say the same thing over and over AND OVER AGAIN, then skip over other crap that would be useful to see, telling about how you did stuff that is not in the video... but NOT SHOWING IT... this is a POORLY THOUGHT OUT and POORLY EXECUTED VIDEO PRESENTATION OF HOW TO SET UP A CARB,... thumbs down, thx for wasting my time, i will go elsewhere to someone willing to put in the effort to show me how to do it, rather than primarily concerned with himself and willing to give a slight glimpse of what is going on.. YOU SUK as a teacher,

I have got an original rear seat from my 1964 TR4 and the two mounting clips are located half way down the seat and about 3 inches in from the sides. Thank you for the video.

"PromoSM" 😕

Alec Is there a part number for your colour tuning equipment? I would like to purchase one of these. Steven

Thanks Alec. I have the same job to do on my 62 TR4.

Thank that really help with my dad's car

HI Alec can you tell me which is the difference between right and left trunion ?i can't see the difference ? i just know someone 3 degrees and 0 degree regards

Do you know how/where I can get this version of movie maker?...(I have windows 11).Thanks.

🤣 "PromoSM"

Hello! Nice video but when I'm trying to updat it, is asking me for the license code, I have no idea how to get it or why. Can you help me find that number or know where I can find it ? Thank you!!

Hello! Nice video but when I'm trying to updat it, is asking me for rhe license number or code, I have no idea how to get it or why. Can you help me find that number or know where I can find it ? Thank you!!

Great video, Thank you. I’ll be fitting mine this weekend.

havent you seen a ratchet spanner

Hi Alec, thank you for your TH-cam videos. Can you help me with explaining how to change the milometer from kilometers to miles??🤔

The previous owners had used standard white matte paint to cover the cupboards (not cupboard paint) and all are peeling. I did a temp repair with some white veneer strips but it seems the type of paint was the cause ??? Moisture on top of the veneer perhaps bled through making the glue inactive? Can I fix it in the same way? I tried wood glue but it wouldn’t hold and became very messy. I’m thinking to buy kitchen cupboard renovation paint and paint over it but need help to fix the peeling.

Hi. I have the same carb set up on a wolseley 6 and they are bogging down under acceleration. Any ideas ? Thank you

I appreciate you so much.

Alec: I was wondering how you were getting on and here you pop up! Love your content. Also love your tools. You seem to have older and better tools, making me wonder if you were in the motor business. It’s easy to tell you’ve been around the barn more than once on this stuff. Bloody good as you fellas say! -Reed

Hello Alec , I have a question for you. Why did you use wood at the outside front of the seat frame ? Or was that just to get a pattern for the back? My seats only have wood the back bottom of the seat frame.

Nice job

Good tip Alec. Thanks

Alec, I’m hoping you are doing well.

did you get any loss of power / acceleration with this leaking ?