วีดีโอ

#11, is the engine blowing up. No doubt

No diff drop?

Will just the 5100's in the front on the highest setting level the truck, leaving the back end stock?

You can do this job without loosening the lower control arms, saves time in disassembly and assembly, use a lower control arm pry tool from astro. I have done this job four times and my best time from pulling the truck into the garage to taking my test drive was 2.5 hours. Hardest part for me was bolting the sway bar endlinks in. Installed 6112s. Nice having a lift so you dont have to crawl around on the floor. Very informative video, this is the video i watched a few times before I attempted this job The first time.

I bought the 22 in September 22 with only two on the lot. I wish I would’ve waited. I haven’t had any issues, they started calling me for recalls immediately. Hopefully they caught everything in time. Turbo lag has happened twice while attempting to pull out into on coming traffic. I take my foot off the brake at most lights or stops, to prevent it. I’m seeing #5 is the most alarming. If you want to drive with the door open, you have to allow it to roll until it self brakes, then put it back in park and back to drive again. Same for reverse, but you can drive with the doors open. I know it still sucks but that’s the only way to bypass the self braking.

64lb-ft for the rear bottom shock bolt, not 5 ugga duggas, and why not replace with the included hardware?

I have had AT tires on my 4WD xterra, and have NEVER gotten stuck in 14 years of almost daily beach driving, regardless of how deep and dry the sand is.... just recently got HT tires on...will I still be able to go 4 low no problem on the beach and not get stuck, with HT tires?

Wilderness Shores???

Smart best comercial ever

That's the most incredible campground in Florida. We where there 2 weeks ago with Tiny Camper Company and was Amazing. Already planning to coming back with the whole crew.

do you know if theirs a max allowable wheel base?

Is it a 3 inch lift or 2.5?

I didn’t need rear block to level it

That bumper is garbage

20 k and no hot water.

Toyota built an overlord . A truck should be a tool that follows the commands of the operator.

Quick question, when extended and putting a 200lb rooftop tent on it my concern is when i get in the tent the extended arms will slide back down because they are only held there by screw compressing the bar. Any issues?

Lee Anthony Lewis Matthew Johnson Steven

Might be a dumb question but, do you put any type of lock tight on the bolts before reassembly?

Your floor is extremely filthy. My floor is meticulously clean with custom fit weather floor mat’s. But great tutorial video on computer mount😂😂😂

Did you have to use wheel spacers w those tires on stock rims?

What are the 2big washers for?

What level trail is this?

Thomas Anthony Walker Patricia Wilson Steven

Whats your opinion on rough country 3.5 lift/ level with their shocks/strut (not a spacer kit), upper control arms? It would be 99 percent on the road. Im getting older and the ride quality is relevant. Ive had bilstein on ford before and very happy, but trying to obtain 3+ inches and run 35s. Thank you for all yall do.

Moore Michael Williams Steven Lee Jessica

SIGN ME UP FOR TRAIL RUNS, if you still do them!! Contact info?

Thanks for the video, fun little trail but unfortunately we don’t have a large amount of trails in West Virginia unless your running a side by side then there seems to be no end.

Hi this product is from our brand Aobosi

If you do not install the 1" block in the rear, will the truck ride lower in the rear? Have 2010 tundra and this is the first Bilstein 5100 install I've seen that uses the top Clip on the front but also installs a 1" block in the rear. Just looking to have mine level with a slightly oversize tire. Great video!

Damn, dude. That looks really good. NICE WORK! 🔥🔥🔥

How thick is that shim that you used to fix the toyota lean?

If you live in the rust belt treat those 3 studs on the top of the shock several times before removing them. The sand and salt sit on that cap and then the nut stick and it is very challenging to cut those off. I just did a Tundra and the back stud on both sides had to be cut.

what shocks do you have in the front to support the weight of the bumper

I have a 2023 tundra platinum. I don’t have no issues whatsoever so far I have 7000 miles on it. I’ve changed the oil twice myself the first time I found some Debris in the oil pan,. I cut open the oil filter and Harley didn’t find nothing in there. Just a few specs but what came out of the oil pan was small small pieces and it was more than I’d like to see. I’ve been a mechanic for 50 years and I rent a fleet of vehicles semi vans, pick ups and others. so finding a little more than I would like in the oil pan kind of bothered me so I changed the oil again. 6600 miles found no debris in pan or the oil filter. I bought the extended warranty with my truck 10 years or 100,000 miles. Why I did it because these turbo engines and these tundras have only been out for two years so for peace of mind I did it also I broke in my engine The way I always do for the first 500 miles. I would drive it at 55 miles an hour 60 miles an hour 65 miles an hour and 75 miles an hour for short distances and then stay at 55. I did that for the first 500 miles I’m gonna be changing my oil every 5000 miles I think 10,000 miles is too long but I am very happy with the truck so far and All new vehicles nowadays have issues i have a friend that bought a GMC truck and his engine has already been torn apart with 2000 miles on it. They change the lifters the valves because it had a ticking noise put it all back together and it still has a noise so they all have issues. He’s very frustrated with this truck, so we just have to deal with it as we go but thank God that Toyota is putting all new engines in these tundras I don’t know what the warranty is going to be. I don’t know if they’re going to turn back the speedometer to zero because it’s gonna be confusing, if they don’t anyway, good luck😊

I'm new to your channel, but I definitely like what I see! I'm giving you a sub and looking forward to more videos! Toyota 🤘🤘🤘

You think a stock 4Runner would be capable of this trail?

Are those the brushed aluminum (bespoke) painted wheels?

Horrible idea to use a screw driver like that to compress your piston unless you are trashing your rotors.

Where is your shop at? I have a 18 Tundra that I would like to get that lift

Is this the right way to get a leveling done to my tundra? People say to just put spacers but i dont know how i feel about that

What tipe should I get for the front of a 07 tundra i would like HD

I got a supercharged 4runner crazy build check out my vieos on it

Hydrolock??

I don't see dynomax Ultra flow muffler for tundra that fits on Amazon

What molle panel is that on the inside of the nobo that is a perfect fit for the back of the food/sink storage?

What’s his Instagram ?

Should have replaced inner seal, that is why rust was inside bearing housing...

Loosen the axle nut before every thing else. A crow bar between the lug studs will stop rotation and allow easy removal..

Do you have a file to download route?