วีดีโอ

hey there I have the same bike and I bought the same system i believe just without the end can and mine has a small pipe that sounds really weird am i supposed to connect it to the airbox? as the stock one is

Thanks for the upload helpful info. 👍

appreciate you!

Hey 👋 my friend , can you supply me with a diagram for the couple feul tanks , because I got a problem that the 2 tanks are not switching for now , can you , please??

What size handlebars are they? 7/8s?

Thank you this saved me a lot of time and headache

Neden vidayı sıkıp sonra geri alıyorsun neden bı anlam veremedim

How did you lift it what you used?

Where did you get those plastics?

Heh I'm going to do the same next week ...found the same issue and also added EGR removal (hose frmo it was melted!)and spark plugs replacement (I like horror moves)laughing through the tears when I watch your struggle man...aliexpress stuff looks the same as mishimoto...got turbo works one for WRX whcih was way too big and without these alu bits for fitting so going to get "dedicated silicone" ones as you did Thanks a lot !

Down to earth good vidio thanks 👍

I mean there's a problem in the electrical connection.. Regards , THX

Hey MR , I got a problem in my Toyota land cruiser 1990 that the main fuel tank isn't replacing with sub one as I use the bottn , how can I solve such problem? Please .. Do me a favor & help me what to do? If it's possible... Thx , REGARDS

what mm was for the removal of the rear seat

Where u buy the lever i need it😢😢?

Brilliant video really appreciate you putting this up

What are the names of the two big bolts that sit on the top of the suspension forks I'm trying to find custom ones but don't know the name

Sorry what is the name of the front disc you mount

I am in Martinique, a french caribean island. your vidéo allow me to fix my 1991 hdj80 wich shuted off few seconds after started. Thanks you very and sorry for my english, no Google translate 😅

What happened if I removed this filter at all???

Thanks a lot for the video. You helped me with doing mine! Cheers!

Thank You save me 🙏

Please measure your chain slack correctly. 20-30 mm is the manual recommendation. The measurement to be done as close as possible to the middle point between front and rear sprockets. The bike has to be on the side stand. Please use a torque wrench set to 100nm torque for rear axel. This video is a very bad example on how to adjust your chain on the SV or any other motorcycle.

Keep it up. Looks much better. I ll do the same with my same bike.

Question....i took the clutch mechanism out of the case cover brfore i removed it. when it goes back together is there supposed be mich movement in and out.

Hahaha I had one of them my 1st ever bike

I have got to do this to my bike just got to new calipers front and back I have to bleed them both u no how u are doing the front I take it u can do the same to the back caliper as well ?

I was going to get that what u put on that yzfr125 glad I didn't now there so bad to fit

Will I be able to fit handguards on these bars ?

Excellent Mate...Thanks from NW Florida USA... JP

Can I install a throttle (the full part from right handle) from a different year on my Yamaha 2012?

Great, I’ll try that

are risers 6?

😂😂😂

Had the same issue, its a problem with the lever and the contact with the pins, doesnt push any break fluid to the break calipers.

Nice.

Love the bar swap. Im wanting the same look for my boulevard c50. Ive seen the risers on ebay, but where did you get that wide handlebar!? Thats exactly what im after!. Cheers for the video

Not a job i'm looking forward to. Recently had similar cold starting issues on my 2.5XT, changed the fuel pump today so tomorrow morning will be the tester. Thanks for posting the video, i did the Outback H6 plugs from underneath seemed easier (more cuts than enough!) , but looks easier from above on the Foz, if i need to change the plugs i'll do the same as you did. Cheers.

Thanks for the video bro it is much appreciated! 🙏🏻

Could you have used the original bars with the risers?

Hi bro.. do you have any videos on middle drive removal and rebuild???

Do you have a link to them indicator plugs?

Finally a vid explaining the air box 👍🏼

What tools did you use to put the Exhaust Clamp on as im sturggling to take mine off, nut keeps spinning and a very tight spot.

Great vid, did it run and drive fine afterwards?

Thank you for this mate! I recently crashed my yzf and had to replace the rear left gear bracket! Once again thank you absolute life saver!

Do you know if the wr125x wheels would be able to fit straight onto the wr125r

Where did you get the connectors (plugs )

love your buggy!!

Some good info there , thanks - seems those seized pins held you up a bit