วีดีโอ

To be honest, I don't know. I've never had a need to look into it

Put your questions in the comments and I'll answer it best I can

@@mrfxr1695 A business cooperation

Welcome !! All the best 👍🙂

About 5-6mm (blue or red packer )all the way around. 10-12 mm total in width and hight. For the thickness, pop the bead in, tension it and measure the thickness. Most modern uPVC 's come in 24 or 28mm thickness, but it's not excluded to be different to that All the best 👍

I agree, one of the resons would be bad aftrermarket one. In my case it regened daily ( every 5-10 miles) with crazy smoke . I've replaced temp sensors and it was all good afterwards. It took me long time to figure that. So far all good , touch wood ;)

Thanks 👍

It would definitely be easier 👍

Maybe it is not fully charged yet, or out of the range of WiFi. Try leaving it on charge few hours to make sure it's fully charged. Reset and start pairing procedure from beginning. I hope it helps

Your right, chain is quite small. I think 1.5 or 2mm Allen key fits usually.

Thank you for sharing this with all. Great info 👍

Thanks for your advice 👍😉

Hi, it's called laser level target plate, they are cheap. Here is the link with next day delivery amzn.to/4bv5QC7

Saves the fingers 😉 All the best

Thanks 👍 I appreciate your comment 🙂

Thanks 👍 All the best

Thanks buddy 🙂 I really appreciate your comment 👍 All the best

Hi, here is full installation instruction manuals.plus/dekco/dc5l-home-security-camera-manual I beleive you don't need SD card for installation, but camera will not be able to record anything without it

También en español manuals.plus/es/dekco/dc5l-home-security-camera-manual

Change the brushes (both of them) and should be good as new 👍

Wait, what, you respected gearbox twice, 😯 I feel your pain

Gonna go argue with mechanic today just went into limp mode again.

Short answer is, for money, it's my job. Long, boring and technical answer is this. See, the bricks are porous, and when it rains they absorb the water. Due to gravity water, would naturally trickle downwards. Now, that masonry sits on the steel beam which forms a large open plan room below. So, without a tray as such, the rain water would come in through the ceiling causing massive inconvenience for property owner (only when it rains)

Some people have suggested turning the valve down a bit, I'm not sure that will work but it's worth a try. Have you tested mains water flow capacity? It is recommended 20 liters per minute. Otherwise a booster pump can help

I didn't had a problem with it 🙂 if it's not broke don't fix it 👍

Ok am înțeles !mulțumesc pentru răspuns !

Sometimes it's difficult to install it through cloud edge app so you can try dekco app

Also, try to reset and and redo installation exactly as per instructions .

I held the button so many times I'm gonna call c.s if not return it . But thank you for the tips ...

I'm sorry to hear that. To be honest, it is quite difficult part of the job. It is very tight fit All the best

Thanks 👍🙂

You have to clear the codes as well

@@mrfxr1695 after two days, the error dissaparread without erasing the error. everyithing is good now

Thanks 👍🙂

@@mrfxr1695 👍

I've just used 18mm MDF board

Thanks 👍

I only know for mechanical tensioner. I've had a look on internet and found this www.ebay.co.uk/p/3004036576 I hope it helps 🤞

​@@mrfxr1695thanks, I'll buy one, wanted to link u the one which got me confused but TH-cam always deleting the whole comment if I link something. It's the same what u sent just with a 2 pin connector for electricity

@@GaborDuzmath I don't know what would electrical part do, maybe a sensor of some sort. Can you see on your existing one has it got electrical connection?

@@mrfxr1695 yeah I guess some sensor, next week I'll take the car apart and I'll see, I'll let u know 😀

@@mrfxr1695 I've changed it, it was the mechanical one, f*cking small place to reach the 3 screws but doable

I feel your pain buddy

Thanks 👍🙂

Of course 🙂👍

Of course, there are many cheep options online

It is P0014

Hi, I'm not sure if I understood it correctly. Smoke on start up that clears away could be failed valve stem seals. Usually issues with vvt would result in engine fault codes. Have you run diagnostics, any codes?

Mulțumesc! Nu an făcut o diagnoza,am să fac dar nu știu ce înseamnă tijă de supapă (poate fi semeringurile de supapă?) AM desfăcut vvt-ul din față pe care lai arătat în clip și nu am putut să scot sita dar la-am curățat cu soluție de frână și tot așa face adică tot îmi afumă bujiile mai mult la piatonul1.Mulțumesc pentru răspuns!

Am o rugăminte !poți să-mi spui la motorul ăsta de 1.6 88kw 120cp peugeot 308sw ce compresie trebuie să fie ?mie mi-a ieșit 9 pe toate 4 pistoane,Mulțumesc anticipat!

​@@mariansandu2451yes, valve seals

​@@mariansandu2451I believe that's too low. Have a look here www.car.info/en-se/peugeot/308/t7-16-vti-m5-6650187#specs

Hi, coolant in the foot well is damaged matrix for sure. Your right, bypassing heater matrix is definitely easier than replacing. On that engine a thermostat housing has multiple outlets. Two back outlets will have hoses run towards firewall and heater matrix spigots. Hoses are about 30-35mm in diameter. This is how I would do bypass of the matrix. There are two options for bypass. One is to remove the houses from thermostat housing and plug/cap the outlets. The other one will be to remove the hoses from matrix spigot and connect them together with short piece of pipe. When refilling system with coolant you'll have to slacken off one of the hose clips from new connecting pipe to let the air out from the system. I hope it makes sense All the best 👍🙂

Thanks for such a detailed update 🙂. I am glad you have successfully repaired your van All the best 👍🙂

Thanks 👍🙂, I'm glad it helped. These engines are very sensitive to incorrect or dirty engine oil and solenoid valves suffer a lot from it. All the best

It is Weber one coat render. This was a trial to see how will perform when used exactly as per manufacturers instructions. One coat, no mesh. I've got couple more videos where I've used mesh within base coat, but top coat has been applied immediately after.

@@mrfxr1695 does it work well ?

@@kennyx.4028 it is ok, especially for small areas if you need them to be completed in one visit. I still prefer traditional sand cement or lime mortar with scratch coat for any decent size areas

Many thanks for sharing this, it's correct. I've changed 4 of these vans and only had a tool kit on one. For some strange reason people don't bother putting it back in the van after use 🤷

😂

If it is ruining for a bit and then stops, it is probably normal. But if it doesn't stop, I would say it might have issue with internal shut off valve, programmer or some of the sensors. You might need to look for answer from suppliers technical support. I hope it helps 👍

@@mrfxr1695 i wish i could reach them; no reply :(. thank you though

@@mrfxr1695 can you do a video on how you would fix it on yours if it continues running without stopping?

@@Sh0esSh0esSh0es sorry I can't. It is not my toilet, it was my customer's toilet

It is DX450 !! I know it is for concrete and steel and I'm NOT firing it into wood. I've bought it with a fault (it had seised ) and I've done a quick service on it so it can be used again safely. All the best 👍🙂

.

What machine should be used?

With a small HSS drill bit, about 5mm. Gently drill out the head of the rivet. Being aluminium it's quite soft. You will need either new rivets or fat screws to put it back together I hope it helps

Thank you for the reply