วีดีโอ

Do you have a chain slide on the swing arm? I have 2010 yfz 450x efi and I have a chain slide that's mounted on that exact spot

good work on the powder coating dude

Good to use it bro? Full credited ofc. Thank you!

🔥🔥🔥🔥

What chemical do you use in your strip tank?

I got the same RC2 gun and hopper setup, works awesome. Nice shop setup.

W vid as always

Hello. May I feature this video in my episode? Full credited ofc. Thanks !

Yikes. It happens to all of us so your good man.

fun stuff man

Hey there. All good to feature it? Full credits + notification as soon as I do. Thank you in advance!

Outch 😊

😮😮😮

That wasn’t a loose bolt it was the tree

fun stuff

Dang, glad your ok😮

Gotta start using that blue loctite I've been using it on everything the past few years over stuff like this

Luckily this was during practice and not during a race it would have prob been way worse. As said above check those bolts before each ride 😮

Note to self: Add this to the Race/Practice Prep Checklist

Hello! Would it be okay to use it in compilations and maybe on some of ours Social Networks? You will get full credit for it. Thanks

good job Murphy 🤣🤣🤦‍♂ . trophies last forever

What oven did you go with?

Oof damn bro. Glad you're ok dude. Im sure you'll get her fixed up good as new. 🤙🏻

Holy smokes, the camera did not do justice on how bad that small tree could cause so much damage. It is good to hear that you will be able to get your quad back in action with a couple of parts. Also, you mentioned that you do not care to ride much in the cold. Who does? Ononewheel7 put a quick video out about the Tusk heated grips. They cost $45 at RMATV and after seeing how easy they are, I got myself a set. They sure keep the fingers warm.

Glad that You Are Not Hurt Any More Than You Are! Quads Can be Repaired, it Takes Lot of Time for Broken Bones, or A Concussion to Heal Up.

That was a hard slam man glad you’re good!

🔥🔥🔥🔥🔥

What is the 24v battery for

Can you get me a parts list of what you needed to make that vapor blaster?

I polished my 250r cylinder 🤣🤣

What size oven is that? Also did you have a floor put in it?

Snow rides are the best You need some studded tires for this much snow for sure. We just got 4-5” of some new snow last night 😎

How much all that cost ?

Hey man just wanna comment and say your inspiring a lot of people

Crazy battle with Eli and Jett

Nice setup bud….i made my own oven and spray booth similar to your setup. Im about to upgrade the shop air to larger piping, how have you liked the rapid air system so far? Couple things id share with ya from my own experiences, and is why im choosing to go with more rigid pipe for my air main lines, is any of those little bellys you have in the air lines will tend to hold moisture. Also every time you have a riser or a drop you in your main line you should do a Tee and go to the side with you air hookup and continue a section of straight pipe down with just a manual valve so you can just crack them open and close quick to let any water out. Same reason i was saying avoid the bellys in the pipe like I seen by one of your conduit boxes and try and slope the air line I’d say 4” for every 50 foot to a drop down with a drain on a long straight main line run. With your piping you can also use tees and with your drops go up towards the ceiling and bend and loop down to the drop as long as you have a regular drop with drain after that or the piping is sloped the other way. Setup looks great just sharing some things i learned along the way. I ran 6/2 aluminum clad mc cable which is awesome and aint got to deal with conduit down to my welding machines and plasma cutter. Only thing i wish now is that i would of ran 6/3 instead because of course thats where i wanted to put my oven and could of utilized that but with no neutral i was shit out of luck 😢 But yea if you go to an electrical supplier turns out the mc cable was or is actually cheaper then romex or thnn wire and comes in a nice aluminum jacket already, makes no sense but supply and demand is what i was told. I think once you use it for any more electric runs youll never use conduit innthe shop again haha

Nice setup bud….i made my own oven and spray booth similar to your setup. Im about to upgrade the shop air to larger piping, how have you liked the rapid air system so far? Couple things id share with ya from my own experiences, and is why im choosing to go with more rigid pipe for my air main lines, is any of those little bellys you have in the air lines will tend to hold moisture. Also every time you have a riser or a drop you in your main line you should do a Tee and go to the side with you air hookup and continue a section of straight pipe down with just a manual valve so you can just crack them open and close quick to let any water out. Same reason i was saying avoid the bellys in the pipe like I seen by one of your conduit boxes and try and slope the air line I’d say 4” for every 50 foot to a drop down with a drain on a long straight main line run. With your piping you can also use tees and with your drops go up towards the ceiling and bend and loop down to the drop as long as you have a regular drop with drain after that or the piping is sloped the other way. Setup looks great just sharing some things i learned along the way. I ran 6/2 aluminum clad mc cable which is awesome and aint got to deal with conduit down to my welding machines and plasma cutter. Only thing i wish now is that i would of ran 6/3 instead because of course thats where i wanted to put my oven and could of utilized that but with no neutral i was shit out of luck 😢 But yea if you go to an electrical supplier turns out the mc cable was or is actually cheaper then romex or thnn wire and comes in a nice aluminum jacket already, makes no sense but supply and demand is what i was told. I think once you use it for any more electric runs youll never use conduit innthe shop again haha

that honda done better lol

I just came back from my snow ride.check out mine if you want it’s on my channel

Snow ride babyyyyy!!!!

🤩🔥🔥🔥🔥

good video what gun setup are you using

That ain't nothing come to Pennsylvania in West Virginia I'll show you some hills😂😂😂😂😂

Can’t wait for this season! Excited to run mwxc!

Is this mwxc

What stripper are you using?

Hey not trying to tell you how to run your business but when handling parts you are about to coat you should be wearing some latex gloves to minimize oil transfer coming off of your hands. Anyway good video cheers!

Damn....nice job brother. Can you give me a quote on a 400ex frame? It will need to be cleaned up first.

Gotta love the orange yfz build

Hey Tyler....I ride an 08 400ex with 416bb stage 2 hc....11:1 JE piston. I like to ride fast woods trails. Should I swap to a 450 carb or fcr. I already have both. But is it really worth it? Also should I even bother with lightning the flywheel? I build a lot of bikes so I have years of experience (I'm 42y.o.). Sometimes its better to just leave things alone. Just seeking your expert opinion.