วีดีโอ

Hi??

in this car the wheel speed sensor is also The ABS sensor that you replaced? thanks

Didnt the gearbox is over filled with atf? The mid screw is for levelling.

Hello Sir. Thanks for your video. What would cause the fault when testet “voltage stabilizer” the engine fault comes when ECO is on. I turn it off. Faults i notice Are. Start stop does not work. Glow plugs indicator lights for 30 sec when ignition is turned on. Heavy start at times.

How to choose the measurements of the radiator, or even if they are of similar measurements, are they worth the same? ...also, disconnecting the battery being a start & stop, does it work by removing the positive, or do I have to do something else...I have a 508 sw from 2016. thank you

Can u give tutorial for changing,fuel pump and hpfp ? 🙏🏻

Y a t'il une programmation a faire , après le remplacement du BPGA?

Useful ❤go ahead!

How to replace vacuum brake booster

How to get the gas pedal sensor for the nissan lafesta mr20

In that year the 208 did not had 3 cilinders so wrong car or date ? WAKE UP ,!

Bonjour. L ecope d air a eté modifié a l entreé. 😊

Music is nice, thanks for the info! I have a 1.6 vti too

is there a specific brake fluid for peugeot 508

which kind of fluid to use for peugeot 508 2.2 2011 ? and is it the same proces ?

aerodynamic parts not included

No matter what i try i cant seem to get that first connector off

you forgot to put the 2 fuses from the old one onto the new one?

Great vid, can the filter go in the housing any way around? Thanks

Could this be the cause of an electical curcuit fault which drains the battery after 2 days of none use. Thanks

Halo bang.. Boleh tolong bagi sy faham Beside Total LV MV. Apa lagi minyak transmission comply Jws 3324?

Thanks for your video. Please, should i change the transmission fluid iñ my Peugeot 3008, 2011 model, though the car manual said dont change the oil? I have 60000mileage on the car, and i am having incorrect gear ratio - P0730.Pls, what should I do? Thanks in advance.

If you cant tell the difference between pads and brake discs then you arent going to be helpful

Is that 2008 the same way to do it? Thanks a lot.

hi, i took of like an idiot the nut covered by the orange tape, when re fitted I now just get 1 click when iu try to start the engine and no lights works, any ideas? could that just be a blown fuse

Best engine ever.

Hello, could you make a video of how you change the oil in the differential of the 308 GTI? Nice videos!!!

Should the engine start when bleeding ?

does the 2017+ 3008 have an undertray with a million bolts in the way of the sump?

What a terrible design stick to ozzy and us and uk design cars what were the French thinking

Really good video, thank you. Made the change so much easier.

Could you tell me how much oil? 5L?4L?

👍👈 How to properly charge the battery with a start-stop system, is it possible not to disconnect it from the terminal? What kind of block is on the battery?

Question does the same method apply to the 308 sw on a 16plate, also does rear abs speed sensor if i got a new one come with loom..

The drain plug looks to me like it’s the level aswell, fill it up! until it starts coming out that tube on the bung I’m guessing.

Hi Does peugeot 208 petrol car have fuel filter?

1:31are both cables positive? or negative and positive? Thank You

It's understanding that the top part of the fusebox holding the actual fuses DOES seperate from the rectangular plastic frame beneath it. After that its easy.

I did this job yesterday. A few things to note. Clean as much as possible before you remove anything. Take photos. Get the car as high as you safely can. Get a rubber mallet to hit the wheel with. It'll probably be fused to the hub - mine was. Get one of those screwdriver-handled telescopic magnets, to retrieve the hex bolt when it drops into the hub back-plate. Mine did. Have the right length hex key - the longer, the better. Have a good torch. Have a can of WD 40 to hand. Once removed, clean the location for the hex bolt. The spring clip attached to the old sensor was so rusted in place, it stayed buried in the crud, and made it impossible to locate the new one. Don't forget to re-tighten the wheels once the load is back on the car. I only attempted this to save money. It took me a couple of hours, and the sensor was £16.99 from a well known online auction site. The only downside is, I used muscles I'd not used in years, and now I can't move! 😂

Did you do this with the engine stone cold, i.e.first thing in the morning, or wait a while after it had been running.., i.e wait 90 mins ?

Great video, thank you.

Merci 👍

Hi, owner manual doesnt say what grade of oil to use. Can you please advise for 2014 pre facelift 508 gt 2.2 hdi?

Quand vous faites des tutos, soit ils sont destinés à des pro (alors pas grand monde pour y trouver de l'intérêt) sinon appliquez-vous à donner du détail sur les fixations et évitez les accélérations.

For a 3008 2019 how many liters should use..?? About how many time should be the engine running before to drain it..??

What is the symptoms of old gearbox oil?

That is COMPLETELY wrong you do NOT take the positive off first.Rubbish video.

Hi! what is th correct GAp for the sparkplug