วีดีโอ

Great video guide, will the "How to install spot lighting " video be available soon by chance?

Excellent thank you!!

What about wall outlets

I don't think this is a good video at all. Following these instructions can lead to water ingress. You need silicon between the tray and the wall where the gap is, also definitely on the wall behind the cladseal strip where the holes are, also where the mitre join is and on the bottom where the panels sit. Also, some trays don't have a ledge that you can push the cladseal onto. No mention or demo of Step 3 in the instructions stuck into each strip - the need to notch out the mitre joint and fill with silicon.

At 1:40 you didn't push down the cladseal strip to compress the sealant, so you had a void at one end of the strip that you then smeared over with sealant. Not very good!

Is it possible and safe too put the panels directly on the wood? In case for a bathroom

Great instructional video👍👍 One question, what's the best type and size screw to use?

That pattern repeat is too obvious. Surely you need to offset the panel to avoid those obvious repeats.

noticed this installed on osb board, does osb need need any preparation and do you guarantee the adhesive

What does trim stand for?

Look good

What about waterproofing the wall before add the panels? I’m confused because that adhesive that was applied doesn’t seem enough to keep water from seeping in.

Awkward shaped room - Is there any reason why the panels cant be fitted horizontally

How heavy are panels?

do these loose their colour if direct sunlight is on them for a while ? i left some old bits outside and they went a funny brown colour from white

Nice🎉

Can the 5mm pvc panels you sell be fit over existing 5mm pvc panels

Shower panels were not joined together properly. Very thin gap in middle of two. Is there anything I can do to stop it from lecking?Other than taking down the panels down and starting again.? Help!

I have been looking for a video that shows how to install your coving before I begin to do the ceiling panels.

Sabse bekaar maal hai 0:17

A very professional video - a template for how instructional videos should be made. This young man is an excellent educator - top marks!

I Installed these with Tec 7 adhesive no ugly screws over a year ago

Will it stand up to showering long term though?

Can you put the panels above a row of tiles and what would be best to make a waterproof seal between the both of them thanks

Do you still use an end cap if butting up to a shower screen

About to do my bathroom and buying from you guys! Never put up panelling, and im not a great DIYer. So your videos have really helped, so thank you!

Can I buy the wall panel trims from you

Um ,What if the last board is only 3 inchs wide, should u not measure the ceiling fitst and split the difference with the first board ,ie start with a half board plus 1 1/2 inchs ,this gets it even and not messing with a wee bit

❤

I'd seen enough when the idiot was attempting to use a saw😂😂😂😂😂😂😂😂😂😂😂😂

When the manager volunteers you to be the face of the company. This guy looks like i feel at work.

How would you secure the trims to ceramic tiles if I was to adhesive direct onto tiles in a bathroom

If its tiled up to the ceiling, does this not matter, still same process? Or would it be better to have been tiled up to the panel? Thanks

When you use a internal corner trim the top trim doesnt cover the end if your only going half way up the wall, how is this finished normally?

Am i correct in saying the profile for the shower sits against the wall panel with copious amounts of silican??

Is it me or is that a strange base? Don't they all have lips that extend up that you put the wall in front of so water won't just run off?

Hi mate, You said no to bother with Silicone as mould will appear over time, another guy from your company put silicone on while fuitting on another video??

what about cutting round pipes/ shower controls etc?

What kind of panels are these?

Great video, thanks for the tips.

The awful music

Help with out of plum internal corners. Would I fit the trim to the board then to the wall ?

Silicone - sealant? Or adhesive? I take it every panel has adhesive on underside lol

How would you finish a board against a shower enclosure wall mounted upright? Many thanks for the video 👍

In your video you cut the base trim to fit the shower tray all the way across. My panels will go beyond the width of the tray. How do you fit the shower enclosure with the Cladseal effectively running behind the shower enclosure wall mount at the bottom? Hope that makes sense.

Do I have to protect plaster board underneath water proof it

Great video James. I have been advised that the Cladseal strip is only for aesthetic purposes and not necessary when installing your panels. This seems to conflict with what you are saying on the video and the use of the strip would prevent water escaping out of the shower enclosure. Which is correct?

If the panels are to go completely around the bathroom walls, what is the best method of inserting the final panel as it will need to be received by the groove at one side and either a corner trim at the other or the tongue from the panel next to it. I am guessing that it might require the last two panels to be inserted together both initially angled slightly out from the wall until they are pressed flat against the wall?

Cheers! I needed this

How big is one of these panels please?