วีดีโอ

I literally just did this. I had zero skack and had to unscrew 10 brackets the length of my basement just to get a little wiggle room and still used a pex spacer.

From the Sharkbite FAQ page: NOTE: The tube liner is necessary for use with PEX, HDPE or PE-RT Pipe. It is not required for copper or CPVC, however, it is not necessary to remove the tube liner from the fitting.

Nop you don’t you never have slack

That looks really safe water right next to electrical box

Made up install,you never have slack!

Hey man. Next time don't cover up the action in your video with the script. Couldn't see your work half the time.

Never use a ball valve where it might be subject to freezing. When they are closed, the water inside the "ball" will expand and crack the fitting. Don't ask me how I know.

I've never removed the plastic bushing, no matter what type of tubing I am installing a Sharkbite fitting to.

Never use pro press stops. Just use a male adapter and fip stops that way repair isn't a huge ordeal

Great job. Anyway you could add Links for the tools you used.thanks

Finally one where the silicone had to be cut through. Thanks for the information!!!

You put the Mack gasket for the pop up drain upside down. The beveled side goes toward the sink drain hole and the flat side toward the nut. Otherwise a very nice job.

Good

Or you could just replace the guts in 2 minutes.

How do you separate the two cut ends of the pipe to get the valve installed. My existing 3/4 supply line has no ability to move back and then forward to insert into the valve ??

Showing how to remove a solder valve was informative - first 2.5 minutes. That said, this was not a “slip valve. Sharkbite Slip valves are longer and installed first past the insertion depth mark, e.g. for 1/2” the depth should be 1” (NOT 3/4” as shown) then, pushed back, using their tool (or something comparable) to the adjoining pipe depth mark. In reality, you will not have the “play” to push the adjoining pipe in place as presented in this clip, thus that’s the beauty of a slip valve.

As a plumber since 1991 I can honestly say I love when these get used by non plumbers. When they go away and something else in the area goes wrong I cut out those valves and put em in a bucket for emergencies only 😂

video needs editing. A lot of our time wasted talking about mistaking a screw for a nail, being surprised that a fitting is screwed into the interior pipe more than hand tight and lamenting the wrong size replacement in the bag.

Waaw

I have never heard that tool called a nose plier. I've hears needle nose and also long nose. Something different!

Love the discipline to have all red and black tools. Good video

Good

Good

Good

Good

🎉

Good job, as usual plumbing is never straight forward!!

No one that is using a propane torch should be giving plumbing advice

Ball valves: install the handle pointing downstream when open. This shows the direction of fluid flow.

The original was soldered and he has a propane torch . Why not just solder another one in it would be so much easier LOL. Too many processes to achieve so little.

I feel like this is missing how to secure the bite.

shark Bite🤣😂😂

No, you don't usually have slack. Your lucky if you have slack.

Should have used compression if there's not enough pipe to cut and replace later

Thank you for taking the time for showing us video's on how to save money instead of hiring them Plumbers! Dawolf is just a hater and he's that plumber wanna be or is that's trying to rip ppl off.

Thanks for the tips where did you get the floor? I’m remodeling my bathroom and I like it

Don’t mind Dawolf he’s just angry and probably hires unlicensed people at his house😂

The fact that your using a bag to remove a trap and a butane torch and all of the other things that you did just goes to show that your not a licensed plumber . Smh

Where’s that AI voice from? I hear it a lot.

Idk why this was so intriguing to watch

This is why I just hire a bonded plumber who knows what they're doing. If you have a large home and you're doing reno then yes it makes sense to learn to do this and get the right tools.

Nice!!

Thanks for the video, clear and to the point!

I've never seen a cleanout like that. Where is this located?

Great job 👍

Check Out The Full Toilet Installation: th-cam.com/video/iFSIGYPsvlg/w-d-xo.html