วีดีโอ

@@jakegamez3720 yes, I am now 5,7 but when I first got it I was 5,3 and fit fine, it will just be your tip toes on the ground but your will grow into it fine

@@YohannSeeger I convinced my parents by paying for half of it, but you could also find ways to make it profitable like TH-cam or door dashing and stuff. You could also suggest using it to commute places, I’m not sure if you are old enough to have a job or not but saving gas money on cars by using the bike is a good argument as well, these are just things that worked for me but its different for all parents

@@ChargedTalaria thank you so much, I already have a super73 s adventure that I could easily sell for 2k, but my parents just think that it is too dangerous or I will just want another bike, but I really appreciate the advice, thank you.

@@Siah-j1p it’s just a bolt on the bottom

@@AustinRosales-q2n Ignition Key Switch Lock 2 Wire -... www.amazon.com/dp/B0118LT2U8?ref=ppx_pop_mob_ap_share

@@TurboLagVr it’s about 300 dollars from Lunacycle

@@mrcleanhasagyat the kitchen, I be cooking up a fire video

@@jackwentling4221 I use a go pro hero 10 paired with a purple panda microphone, don’t forget the microphone adapter for the gopro

@@Brecken.S Amazon

@@JosePerez-hv1fr so depending on how you did it, yes and no. It is apart of the red white wire to red black, if you don’t want that, connect red solid, to red black. But if you do it that way, every time you turn on the bike you get an error code, it goes away after pressing start, but it is a little inconvenient. I didn’t mention it in the video as I recently discovered this. So it’s up to you

@@ChargedTalaria Im just wondering if you know if that’s bad for the bike since I charge it overnight

@@JosePerez-hv1fr no it will be alright, because it stops charging and turns off at 100%

@@johanedelbro6360 5,7

@@JosePerez-hv1fr on the ignition, or the rfid

@@ChargedTalaria like did you have to extend the wires for the new key ignition? Or no

@@JosePerez-hv1fr no

@@JosePerez-hv1fr yes

@@wspdaniel132 just a rectangle of sheet metal with two holes in it, just to raise the plate a bit

@@ChargedTalaria Where did u get it? Can u send a link

@@wspdaniel132 it’s custom

@@ChargedTalaria How did u make it

@@wspdaniel132 tin snips, sheet metal, and a drill

@@juusotee4340 yup

@@ChargedTalariaBro i have talaria mx4 2024

@@juusotee4340 sweet dude! Can you wheelie?

@@ChargedTalarianot yet i’m trying to learn it vut i can wheelie a litle bit

@@juusotee4340 don’t loop the freshie🤣

@@MaryanPodilnyak-wq1ih it’s the upgraded display from lunacycle

nope

@@JonahKennish I got it when I was 5,3 so anything above that i would say is great

@@ryanclark7913 it just plugs in

I said don’t ask😂

@@snowi9978 will do🫡

@@ChargedTalaria thanks

@@KhaledSharhan-b9h I have the go pro hero 10, and it’s great

@@griffinroxs4412 lunacycle.com/talaria-large-color-display-for-xxx-and-mx4/

thats odd, you may have cut and connected the incorrect wires. If you want you could give the key switch a shot

@@ChargedTalaria I got the key switch it works . But if it turned it on and off abunch it would stop turning on untill i disconnect and reconnect wires . I got the key and left nfc disconnect . The light also flashes at times weird when turning on I did that switch install on the nfic module for the chip looks very clean easy to do it’s like a double security measure as well you gotta flip it to Turn on bike and I turn it off when leave it and charging turn off it doesn’t make all the lights turn on

@@ChargedTalaria wish I could show you photos Amazon came in clutch with the switches and key ignition

@@markospina575 if you want you can dm me on insta

@@nicobluey5383 so there’s a bolt underneath the motor that i connected to the frame and motor, you remove the plate and tighten the bolt until it’s tight enough, search a video for talaria x belt maintenance

No, it comes that way😊

So your bike came with your rear brake lever was on your left side?

@@MOOSEVR7 yes, it’s not cheap tho

@@yaminhelal6445 I added some sheet metal to raise it, then bought a longer screw for the top

@@ChargedTalaria how did you raise it with sheet metal

@@yaminhelal6445 I cut two little holes, put one screw through one hole into the frame, then another screw into the plate, then repeat on other side

@@ChargedTalaria I know this is asking a lot but do you think you can post a video or tutorial showing how to do it

@@yaminhelal6445 dm me on insta I’ll send a pic tomorrow

So i used two pieces of sheet metal, cut them to the right distance, drilled two fitting holes, then i used a set of nut and bolt to fit the plastic cover to the brackets, then the stock bolts to fit the brackets to the frame, its kinda complicated but it works well

its just some sheet metal i cut up

If you look at lunacycle it’s called upgraded talaria display

It depends on how you feel about the responsiblility of the bike. It is a 3 thousand dollar machine that could really hurt you, but if you feel like you could handle that and if you are tall enough, it is definitely the best choice.

@@ChargedTalaria Thanks! u got a sub!

I haven’t found a way to, but it will work with any key I assume

sorry for not seeing this sooner, ive come down to the conclusion that the bike turns on when charging due to the rfid being bypassed, it makes no sense but thats the reason it does it, you could possibly find another way to bypass it, then it wouldnt turn on, but in the meantime i done know how to fix it, and you can do it with a surron or talaria key, but i dont recomend the surron key, because the surron has universal keys, im pretty sure, making it less secure

@@ChargedTalariawhat if you created a simple switch instead of connecting the wires . So you can turn of the chip iefd connection when charging or not around

@@markospina575 if you are doing that, lmk how it goes, that’s an interesting idea

@@ChargedTalariawhen the bike turns on while charging, does it stay on or can you turn it off?

yes it does. its really weird but i dont think it is bad

yea ik I wonder if it can be stopped, thanks for letting me know

@@coca-colaaddicted3156 im thinking maybe instead of changing wires at the rfid box maybe if you bypass the scanner part by just twisting the two wires together to skip it, maybe it wouldnt turn on when charging.

yes, you can just replace the button with the ignition and keep the rfid active

It’s a bracket for a screw to hold another screw, you could also cut a piece out of a sheet of metal or something. So it’s just a custom piece