วีดีโอ

Quick and easy… thank you!!

To everyone asking about the access port. If yours doesn't have one, then you do have to remove the entire wheel well cover. You need the t20 for one or two screws, then a 9/32 socket for three bolts, and finally a screwdriver and needle-nosed pliers for about a dozen plastic pins. For the pins just pry the middle pin up and use the pliers to pull them out the rest of the way. Hope this helps out alot.

Thank you!

ok those bulds were the high beams low beams are the H11

Not too bad, thank you !

Absolutely...Awesome and straight to the point.

This was straight to the point, no wasted time and it was easy to follow. Thank you just saved me some money.

Thank you. It looks easy enough that I can do myself

YOU NEEDED HELP HOLDING THE CAMERA DIDN'T YOU. BUT THANKS. NOW TO TACKEL MY OWN LIGHT. I SURE MISS THE OLD CARS!!!!!!!!!!!!

Thank you for this! This helped so much!!

I have a 2014 Equinox LTZ that did not have the wheel well port. Had to loosen the wheel well front outer and bottom perimeter screws and pins to get my arm in there. This video is for the outer low beam bulbs only. It takes some effort to get the bulb socket cover back in to rotate it. The original low beam bulbs are H11 unless you change both sides to a brighter bulb. We need a video to show how the bright bulb gets taken out. I can't see it unless maybe the whole wheel well lining gets removed which may require removing the front wheel.

Nice thanks

Thanks for the video! I would suggest turning the wheel for easier access or even taking it off, lol.

Thank you 🎉

Thanks

You saved me my guy much appreciation for making and posting this video if I could shake your hand I would 💪

FYI - The LTZ trim does not have this access panel in the wheel well.

You did a great job showing this. It would’ve cost me $70 to have it done at Pep Boys for a $15 bulb.

BTW if you try and try and try and the cap won't go back on, reach up in there and feel around the opening where the cap seats. You might find that a wire has looped out and gets between the cap and where it goes. Just tuck that wire back in and your cap should seat and screw down tight after that.

The best way to change bulbs in one of these is to drive it to the junkyard and buy something different lol This process is absolutely ridiculous.

Thank you for the ez instruction.

Bro why u have rhe chevy tailgate and gmc front bumper

Great job

I've been around too long. I remember when you popped the hood, reached down and removed/replaced the blub. OMG!!!!

Thanks for your help. Stood there scratching my head. After watching video no problem.

How do I remove the cap??

You need to make sure you let people know that the access panel isnt on all 2014 models.. waste of my damn time

This is the only video that shows the access port. Others show removing screws and p I lying out liner. I have a 2015, does it have access port?

Helped a whole lot going to try it have two head lights out and they was trying to charge me two hundred dollars to replace🤦🏾‍♀️ty😊

My 2014 Equinox doesn't have a cap or missing a cap on my passenger side. I've double-checked my driver side, and I see that one,

Bruh earned yourself add subscribe

Good job

Saved me a headache thank you so much!!!

Here in 2024!: Glad I watched your video. I was really considering going to a garage for this because I was very weary on doing anything myself to my Equinox that’s still under warranty for maybe another 6 to 9 months. Huge confidence boost! Thanks!!

Sorry my 2014 doesn't have the circle hub to take out mine is one long piece

Very helpful

Thanks for making the video!

Yeah H11 is the low beam, 9005 is the high beam. Probably wanna correct that

thank you

On the 2014 you have to take out or losing the inter plastic fender to get to the headlight ,be careful the plastic is very sharp it will cut your arm when reaching up to get it out.

Never said not to touch glass. And never said you were only changing high beam.

I searched this to replace my headlight in 2014 equinox-this is NOT a 2014 he’s working on looks nothing like what my 2014 equinox looks like!

Would you do this for me tomorrow-?

Everything went smoothly but wrong lights needed H11

What was the low beam headlight code?

Thank you for this video! I went to 2 Auto Zones and an O'Reilly, AND a Tires Pkus and none of them wanted to put the bulbs in.

I did my 2016 led bulbs this way great video

This was fab! Thank you!!

Look less complicated than removing the front clip .

Another way for me to try, originally I was taking loosening the black panel around the access point. 🤦🏿‍♂️