วีดีโอ

I imagine they’re still picking up bearings off the factory floor. 😂

Where did you find the parts? Except for the music dubbed in, great video.

Could you tell me when you bought the rebuild kit thank you

💪 Thanks

Can these parts fit Oliver 550

where to purchase cup and retainer

I think this fellow did a great job with this video verry clean

Would have been good if you showed how it went together, with the marks lining up, for those of us who want to repair ours, that haven't done one at all.

Thanks for the videos. I have to open up my Dads gearbox seeing that it only turns one way. Turn it the other way and the shaft turns out 🤷‍♂️ thanks again for your time!

Painful to see China on those new parts 😢

Good job

I replaced mine a few years ago! 38 in deck, got replacement from Simplicity dealer. It was around $500.00. New one is already starting to flake off some rust when I scrape it out. I started to keep it cleaner now as I want it to last for the life of the tractor!

The I&T manual says the ball nut and worm shaft are not available separately .

Where did you get it and how much did it cost?

I put mine back together, can only turn left, how can I remedy this ? Thanks

Does the shaft have to be lunges up maybe halfway when you put it in.... like in a certain position with the tires ??

How do you check it for the fluid level

Do you have the part number for the rops on ur ferris mine is the same one and I can't find one for it?!

Sooooo, I sat throught the most painful youtube video to find out how you adjust the wormgear. Thanks for wasting my time dude.

A little less talk

My husband and I learned little from your steering wheel repair. Wish you had shown how the worm gear went back into the gearbox and aligned. Also, where you got your parts list and purchased them.

Great series! Have watched it twice. Bought a steering shaft, ( old one broke) I am not taking out the sector gears. The thought is they are already aligned with each other, I just need to align the Ball nut to the sector gears. What am I looking for with the shim seats. ( min. axial movement? Do I start by having the ball nut at the bottom of the ball screw? half way up? Any tribal knowledge on this would be great. Again thanks for the time spent on this.

This video was such a relief to me. I now know that I am not the only person who has to fumble around with something before figuring it out. I have been doing mechanic work for 50+ years and it still happens occasionally. The fumbling always humbles me. Like you, I do not give up and finish the job, but honestly, you seem to be more patient than me. Thank goodness you did not edit out your mistakes. I am serious but have to admit that I had a few laughs along the way. Well really I laughed until tears were flowing and my wife wanted to know what I thought was so funny. Thank you for this video series.

There is no any problem in varm and lock why are you dismantling it

Balls are new or old?

Is you used equal numbers of balls in Upper and lower lock?

any idea how to get the race out of the bottom of the gear box where this bottom shaft bearing sits?

Does anybody know where to put the 90W gear oil, and do you have to remove the hood to expose the gearbox to lube it?

Thanks for all the time you put this video together. I'm sure a lot of guys are nnow going to respect the steering box more and more like me. I'm afraid to touch that box and hope I never have to repair anything there, but the least I can do is grease it. For my 8N, do I use grease, or 90 W oil. I read somewhere and my notes say use Cornhead pourable high EP grease, another guy says to use 90 W oil. What's the real answer? Thanks again.....thumbs UP!

How much for a replacement deck

Kevin zeitz Great link Man helped a lot, thanks

Was that the fourth valley of the gears? which side of the valley to make sure the gears align to the right side?

Which side does each gear go on and what number is the tooth to align each gear together or do you just center the teeth? I took mine apart and forgot which side the shaft goes in to each other. How do you align the ball sterring gears on the shaft to the teeth on the two side shaft?

Need a diagram of that . for the pulley wheels can you help.ted@kcweb.net

Great series! How much gear oil did you use? Thanks!

Great job on these videos. I really appreciate it! Jim@VintageGraceTexas.com

RTV will not seal because gear lube as well as transmission fluid will reject any RTV silicone over a short period of time. If you use anything here use Permatex gasket seal here.

Dry Ice in Acetone shrinks the bearing race while the Acetone prevents ice crystals to form while the dry ice shrinks the race as well as prevents the Acetone to boil off so the race will pretty much drop in.

Nice and informative video series! Where did you get all your rebuild parts from? I seen the packages on video 2, but couldn't really read them.

This video was worth watching. Some things I had already been through but the re-assembly was not working well. The book I had on the Ford tractor (8N 1950) did not tell me how to sink the two sectors so that the arms were straight down when finished. I took mine apart one more time and found the notches, lined them up and it worked perfect. By the way, don't mess with 90 weight gear oil, use a grease that pours like honey, that way the seals won't be leaking either. Thanks for your work on here.

Dude - scrap the music on your next tutorials !!! we watch to LEARN something - not for entertainment. If we wanted music, we would go to the music channel. other than, YOU DONE GOOD and THANK YOU for your time.

hi, I want to know where you ordered the parts for this. I have a 73 2000 and I need these parts. yesterday my son came in the house and told me the steering went out of the tractor, I went to look at it and if the wheel is turned left or counter clockwise the whole steering shaft moves up and if you turn it right it screws back in

Where is your vid on putting it all together and showing how it performs afterwards? Is it forthcoming?

How long before u put back together I need help on mine

nice job so far.

the video would have been better if you had not tried to play the music at the same time as you were talking. Otherwise, I like your narration. I have an 8 N and would like to see more repair videos as I am going to update mine this Summer. Thanks

I hope your still working on the steering box. Your right, there is no videos showing how to do this. I have to rebuild the early box on a 1948 8N. I'm rootin for ya. Look forward to seeing more

Whats the song in the first mission?

Thanks for checking out my vid and the like.

nice! left a like :)