- 30
- 178 413
A D
เข้าร่วมเมื่อ 20 ต.ค. 2011
Random repairs
como arreglar o reparar mesa que se tambalea
como arreglar o reparar mesa que se tambalea
มุมมอง: 1 342
วีดีโอ
sink faucet pull down gets stuck problem
มุมมอง 7K3 ปีที่แล้ว
the threaded part moves separate from the body .. so before installing it if the sprayer hose moves freely .. make sure the position of the hoses so to keep it that way.. the nut that tights from the bottom .. just hand tightening it and the rest screw tight the two screw that are on it.. so you don't twist the threaded part . I hope that helps. because it was driving me crazy. thanks.
how to install catalityc converter guard
มุมมอง 133 ปีที่แล้ว
bought this kit to guard catalityc converters . has different size shims.. I use one size smaller to make sure the stranded wire that will run through the hole/clamp gets tight. unscrew one side of the clamp to put around the pipe , one clamp before catalityc and one after. Unwind the stranded wire and put it straight , that way it'll be easier to loop it through out the clamps and the car fram...
water leak in to the computer f150 expedition
มุมมอง 4094 ปีที่แล้ว
I put silicone in my expedition to stop the water leak from leaking on to the harness
Como abrir el mango de robot coupe mp350
มุมมอง 15K5 ปีที่แล้ว
Como abrir el mango de robot coupe mp350
Baño no baja el agua bien
มุมมอง 20K5 ปีที่แล้ว
El baño no baja el agua bien . Solo es regular el flujo del agua Quitando la tapa y dando vueltas al tornillo al izquierda para mas flujo o derecha para menos. Ojo ! Hay otras razones por el cual no haya sufuciente flujo de agua , en este cazo esta era la razon. Gracias por ver el video :)
Como reparar Horno convencional - corto
มุมมอง 4865 ปีที่แล้ว
Este horno bota la pastilla /braker/fusible Lo prendí y note que el motor no jiraba .. Para saber si es el motor esta quemado se gira (estando apagado) y despues se prende/se enciende y si jira .. Solo es el capacitor de arranque. A cambiar el capacitor pronto porque si no prender y por mucho tiempo sinque el motor jire lo quemar.
Como ajustar canilla/pluma/llave distancia agua
มุมมอง 705 ปีที่แล้ว
Como ajustar canilla/pluma/llave distancia agua
How to take apart Ekectrolux Bermixer pro B3000
มุมมอง 1.6K5 ปีที่แล้ว
How to take apart Ekectrolux Bermixer pro B3000
Como desarmar un Electrolux Bermixer Pro B3000
มุมมอง 4.9K5 ปีที่แล้ว
Como desarmar un Electrolux Bermixer Pro B3000
How to fix broken door Vollrath vacuum chamber
มุมมอง 1146 ปีที่แล้ว
How to fix broken door Vollrath vacuum chamber
How to put a door on an oven quick and easy
มุมมอง 9006 ปีที่แล้ว
How to put a door on an oven quick and easy
How to replaced Avantco oven broken door.
มุมมอง 2.6K7 ปีที่แล้ว
How to replaced Avantco oven broken door.
Hobart slicer machine. Slicing machine gets stuck.
มุมมอง 8K8 ปีที่แล้ว
Hobart slicer machine. Slicing machine gets stuck.
How to change gear oil in a Hobart slicer machine
มุมมอง 31K8 ปีที่แล้ว
How to change gear oil in a Hobart slicer machine
How to add a vent to an existing sink pipe
มุมมอง 17K8 ปีที่แล้ว
How to add a vent to an existing sink pipe
Saludos😅
Thank you!!! I couldn't figure out what it was. but this checks all the boxes of my problem
@@DeeJayToony I'm glad it helped
Gracias muy buen explicado
Hola. Muy bueno tu vídeo. Sabes necesito abrir el cuerpo de la mixer para cambiar los carbones y no puedo. Ya saqué los tornillos pero el cuerpo no se separa . Debo remover la base metálica? . Desde ya muchas gracias
Cómo puedo contactarlo, para la reparación de un equipo
This video installation saved me money & time.
Just bought this exact faucet and, i was so close to returning it then i foumd your video! Thank you so much!
I'm glad you did. Your welcome :)
Newbies wanna be technicians IGNORE this video's info. It is wrong. Do not use this type of lubricant in the slicer, this is grease used sparingly for parts and axles in the friction areas for when assembling. It is not "oil". Use only food grade NSF specified oils in the gearboxes and do not overfill (never above horizontal axles) coming out of the housing.
@alexsmith9328 that's what the technicians at Hobart Sent me base on the model. You just don't know.
@@fixingstufff that sprocket goes inside the transmission below. The whole transmission and exposed sprocket is oiled by approximately 120 weight "FOOD GRADE OIL" WHICH splashes around to lubricate all sprockets friction points. Possibly the white grease they gave you looks like the grease you would fill inside the tube holding the vertical axle (sprocket below blade in top. You will notice that tube/housing has a little hole in the side you can fill it in. I dont think you will do any damage doing what you did i just know it is not recommended to mix oils (below in the transmission) and grease. These slicers are like donkeys very tolerant so you ll be ok. If you need help with specifics and how to know how much oil and type etc to put in let me know. I was not trying to be rude i just wanted to save some newbies. I am not affiliated with ho art corp i have just taking apart a few hundreds of them in the old days
Donde compro la pieza como la encuentro ?
Bucalo como robot coupe 350 shaft replacement o driving shaft assembly partstown.com
Muchas gracias gran video
@@RafaelSevilla-g7t gracias
I LOVE these fuel cans. Great method of popping the tops, I will definitely give this a try today. One note for people trying alternate fuels... be careful with denatured alcohol. It is my fuel of choice, but you can't fill the can more than halfway - otherwise when the can heats up, it will get hot enough close to the top to cause the alcohol to want to expand a little and it will pop the top off. Although I've had no major problems because of it, I've definitely had some flames escape the stove area due to flaming droplets. So I would say just do some careful experimenting before you decide to refill a bunch and throw them in your pack :) Thanks for the great video!
This is the best video I've seen about these cans. Can I refill them with kerosene? I have a Vesta heater- buying 6 hr cans will add up and kerosene is about half what lamp oil costs. Thank you in advance.
Thanks, you can pretty much refill them with any fuel.
Thank you for a great video, I solved my problem:)
I removed the head to soak and accidentally let the hose retract into the neck. Now it is stuck on the black inner lip. Any suggestions for getting it back out?
If can you grab the hose from the bottom and push it up slowly
Thank you for this video bro, I have that problem with my f150, yesterday rained and today it doesn't start, and the lights just turn on randomly.
Do you know how to fix the round thing that the hook uses to latch onto? They came off and I don't know how to put them back 😢
GRACIAS !
👍👍👍👍
Never pry your equipment like this man is doing.
Chingon
Botão está o botão de ligar está travando como que eu faço para dizer
I have this exact faucet and your video helped me with the issue that I was having. Thank you!
I'm glad thanks 8
horrible audio
Спасибо, добрый человек!
Спасибо, мой друг!
Thank you. Good info.
That’s the biggest cannoli I have ever seen! Lol thanks for the video and the amounts were perfect!
Can you use a different fuel in an chafing can?
Yes, once you open it you can refill it with any fuel
Thank you
donde conciges parte
I looked into getting this lube for my slicer and the small 35oz can is over 260$. Do you know of any cheaper equivalents? I would hate to spend 3 x what i paid for the mixer on this😅
Victor Damone, that a lot! Was it in pesos? Type in your search brand and model gear oil.
@@fixingstufff yes its the exact same fgl-o Food Grade Lube and part # in USD. I reached out to hobart and it was same part number given as what is used in the video. The parts rep was surprised at the price as well
@@victordamone4386 it's good that you called hobart.
Hello! Can you tell me how to replace coupler?
how not to ....
Thing is.. An auto vent won't work unless it above the flood rim of the sink,which is impossible inside this vanity cabinet...just saying...
Still working. Water goes thru and pushes air out.
Gracias Maestro! Solucioné mi problema 🇪🇨
Que bueno Martin Zerda, meda mucho gusto.
Donde puedo contactarlo, quiero le dé mantenimiento a dos mezcladores que tengo
Dude same here it effects my kill switch one day it rained any my radio was on an window was down it's crazy asf bro
That's where the water is getting in.. leaks on to the wires that leads to the computers.
@@fixingstufff how do I fix it from leaking in
@@Enlighten0ne clean in-between the windshield cawl (the plastic) and the metal and put a bead of silicone. I used a black rubber roof silicone tube
Exelente mero y lo abro sin quitarle los tapones
How to adjust blade
Looking for that..just a few questions, can use a gel or alcohol only ? ..and which kind of wick...?
Once you open it you can refill it with anything.
El plástico blanco donde está el bearing del otro lado como se cambia. Se me quebró el plástico blanco y el bearing se quedó adentro y no veo la forma de cambiarlo
Hola Javier. Nunca ordene las piezas para la mi bermixer hasta ahora a trabajando bien.. Pero creo que si tratar con un extracto de poleas la puedes sacar
So where did the original grease go? And if you removed it how did you get most of it out?
Exelente me sacaste de una bronca 💯
Gracias. Me da gusto que te sirvio el video.
crap.
installed backwards, but at least you didn't finish the video so no one think that's correct
Gracias
How can anybody, like or subscribe, to something like this , ( not showing anything)
😆. First video 📹
Well if Biden can be president than I guess you can call that a How To - video...
Lol 😆
Podrías demostrar en un inodoro con tanque y nuevo, porque no succiona con fuerza ??
Si es nuevo el inodoro.. revisa la respiracion (la pipa por donde agarra aire).
Great video! Thanks for sharing the information.
perfecto!
Tengo una rebanadora hobar pero esta tirando aceite de donde le checo se ve de abajo pero noseve de donde me podría desir de do de lecheco
y como se cambia el cordon de la luz??