วีดีโอ

Man stop taking so much and do something!

U made it look easy!!!! I had to find a wrench to hold the pulley so I may loosen the bolts to remove my blades!!!! Ughhhhhh!!!!!!

Thanks for the vid. What’s with the add on you attached on the right side of the mower where the excess grass spits out?

This video is bad in many ways...every part is on backwards...plus the order of assembly is going to make your life much harder than it needs to be....basically put the two small side pieces on the mower FIRST with them oriented to where they point UP not down or it will be way too low and plow....then simply mount the C connection piece to it with the flat side toward the back of the mower not like he did it...if you do the other way it will crimp the rubber mat and screws will appear too short or will be a B to get on... its really so much easier than it would be if you did this way...

What about a torque wrench?

What kit is it?

you talk way too much

Thank you.. great advice and video ❤

Hey man, i seen your video when you first put it out there, was wondering how it's doing now? You think it was a good investment? Just checkin, thinkin about getting one

Milwaukee is good! But, Ingersol Rand is better! Always get the best!!!

The c bar is on backwards.

What is the size?

Great easy video thanks

I changed my blade on my kubota zero ,after market blade but now it making a small noise from the deck like something loose the blade or very tight

Really dump question I have a corded impact that's rated at 450 ft lbs do you think that will be enough to remove the bolts?

How quickly will the bag system fill up? Do you use it for grass or just leafs?

How do I lock my blades down I've tried every gadget possible. 😥

As Kat Williams said,,thats a Icelandic white baby..lol,,🤣

Does anybody tell you the damn socket size in these videos??

Recently bought a BB Maverick and chose the 48" for the same reasons. In the larger deck sizes, several had the same Horsepower as the 48". I'd rather have the enhanced mobility, and more power to the smaller blade surface area=ability to handle thicker and rougher turf if needed. Also less demand and wear and tear on the engine.....in my humble opinion...

An impact driver works. No need for an impact wrench. Some of the other youtube videos show this.

"Tap it 2 or 3 times". Reminds me of college. Anyways, like I was saying, great video! Made me realize how easy this can be.

spindles look small

You have actual light under the deck! Do you know how many nimrods video this blade change in the dark?! It's a lot. Thank u!

what's the detachable bagger part number? I'm trying to get one

You can tell by the good clean bolts that he just put them on. I would like to see someone take off some really hard to remove bolts and do it for real and not to make a movie.

Wow that’s a big yard but using the Bad Boy must be nice. I mow my lawn at about 3-1/2” and it helps make the lines more visible.

Makes sense to me.

Only torque them on with 90-100 ft lbs. If you use anti seize, you over torque.

I always use my impact gun however I literally just sheared off one of my spindles putting the blades back on so from now on I’m just gonna use a ratchet to install but will continue to use the impact to remove them. Thanks for sharing your videos.

Too much fail. Very backwards. This video give you vertigo. And you got the 'kohler engine' ....... lol.

Just tried to get my blades off. 24" pipe wrench won't break the bolts loose. Impact driver won't budge them either. Only 25 hours on this Ariana 60. I'm very frustrated

Kawasaki Engine’s suck!

Should have got a green one.

I been using badboy for 6 years now I love them just trade my outlaw and picked up 2 revolts a 61 and a 36

Any chance to create a video to repair the fuel gauge? It was working, I opened it to fill and now shows empty when full on the 48. Thanks in advance.

Just bought one and it seems to be working great on the field grass

omg dude, you screwed that all up. l and r brackets to frame are on wrong sides and when mounted to frame the brackets should have bolt holes higher than frame. also note, stripper hanger is backwards. notice you maxed out your adjustment and still have supper huge drag? it should be 1 inch from level concrete floor. smh. the lawn guy? quit.

What is the link to where you bought this from?

Great Video! Where did you get that side bag? Ive been looking for a good one for a year. We have the same mower, same year. Good machine. Sometimes I get this strange lone strip down the middle. You?

You'd get a much better stripe cutting at 3.5"

I have the 2019 ZT Elite 54” with the Kohler 747cc engine. And the manual foot lever. I did not want the electronic deck lift. I love it!! I plan on getting some accessories soon. The advanced chute system for sure.

Does this mower work good for a little side gig cutting grass....looking for something in my price range to make some money on the side having small lawn care busines for people I know and family members

I am thinking about getting one too. How did you decide to get the 48" over the 54". I originally thought I wanted the 48". But, that is a lot of mower for a 48" deck. Do you have trouble getting under trees with really low branches at all?

How does it handle on hillsides?

I was told buy a local guy a dollar a minute, does that sound right? Im planning on starting a business

You got a sub from me,Idk why more pros dont use badboys they're pretty damn badass and are built like tanks

I did the EXACT same thing bro!! It is awesome!!

Did you buy from tractor supply?