วีดีโอ

For Sale

Gorgeous! It sounds like it is running on only 1 cylinder though. Gets better as it warms up?

è la migliore motocicletta da turismo di ogni tempo, tuttora insuperata. Nonostante la lubrificazione a sbattimento. Con questo modello la Bmw di Monaco, non quella di Berlino, ha raggiunto la piena maturità tecnica e stilistica, mentre la Vincent è la Brough Superior sono scomparse prima di raggiungerla

Hi Seroj: Could you please let me know the correct values to adjust the valves of the R60/2 from 1968? I found that is 0.15mm for the intake valve and 0.20mm for the exhaust valve. However, there is another adjustment on the side of the valve. Do you know the value? I appreciate your kind help and information.

Had a R69S for over 3 decades and overhauled the engine. They are relative simple, heavy built. Wait till you try installing the crankshaft, you can say "Oh Shucks and many other words a Sailor is well versed in".

It's a 41 mm Bolt. I use a mallet instead of a Construction Hammer.

My bike is very difficult to start. Do magneto rotor need to be re magnetized as part of normal maintenance ( it’s been 50+ years) ?

How do you solve for differential timing?

Wow In the late 70s I bought a r60/2 with a bad crank too. Sent the crank out to have it rebuilt then rebuilt it. Rode it for 5 years before I sold it. It had a full fairing and saddle bags. Loved it but not enough to keep it

This is great information!

I get continuity even points are open . The engine is in bike so I don’t know if that changes things ?

Thanks for making these videos.

Would've been great to see how you installed the new seal. It's always tricky getting those to go in evenly. Any tips? Thanks!

Just a lovely bike! But it sounds like the pilot jets are clogged. Get those cleaned out and she'll purr.

Is there a work shop manual you can recommend to guild you through the rebuild process?

i think it's R50 🤔

Nice job!

My favorite of all classic Harleys the knuckle head

My very first motorcycle was a '46 Harley 61, which I bought in 1956 for $250. I rode that bike for 40K. After riding Harleys for 15 years and about 140K, my brother in law came riding up my driveway on a brand new Honda 750 four cylinder. Took it for a short ride.....goodbye Harleys and I've never looked back. Put over 200K on several Yamahas and Hondas......am now 83 and just sold my final Honda ST 1100 about two weeks ago. Hopefully, one day I'll ride that big Honda in the Sky!

Good tutorial. Have owned my R50/2 since Sept 67, never saw the inside of the rear drive yet. I bought it to get away from chains, it’s working! Thought you would also warm the cover for reassembly. Do you know of a repair for the splines when worn other than all new parts.? Thanks.

I have 2, 73 r75 toasters and a 66 r60/2. If they are not brand new. Roll the push rods on a flat surface. If they are not perfectly straight, you will never get the valve timing right.

I looking for a /2 motor mount for an enginde stand. Any ideals?

Nice Video Seroj! My question is: Where can i purchase that mini tool? I cant find it at cycle works. Thanks

Thank you

Just what I needed for my R50/2; I wasn't sure whether I should attempt it or not. A pefect tutorial.

Seroy, I like to thank you for your very clear instructive videos.

Wonderful condition - the colour is very nice - unusual but really suits the bike . . .

Nice bike

Hey man, we are in the middle of rebuilding this same engine. Was hoping that maybe we could reach out through email or something to ask a question about the bearing at the end sitting against the crank timing gear. When we put it in the bearing couldn't spin.

Muito parecida top

il volantino dell'ammortizzatore di sterzo non è appropriato. Non appartiene alla R 69 S. E, soltanto per cominciare ...

Excellent job explaining this to a novice as iam . How often do you clean out the slinger as far as periodic maintenance? Thanks

Very well done video and knowledgeable demonstration of how to do this. Easier on the bench than lying on the ground!

i remember my dad buying one of these bikes , brand new when i was a kid . It was my first motorcycle i ever rode on the streets . It was a really great small bike for local putting around .

Traducir al español de chile

Traducir al español de chile

Traducir al español de chile.

Traducir al edpañol

Si lo pueden traducir al español.de chile

Good job explaining this .

That was THE best video/explanation I've seen. Especially how to adjust the points. Thank you very much

Piękny

Hello, you're so good!"

Beautiful bike

Where can I source the all-in-one tool that you use in the assembly?

Awesome! Thankyou!

Can you do a quick video on your R60 compounds and tools? I’m about to rebuild mine for the first time.

Excellent video series!!

ราคาคันนี้ประมาณเท่าไรครับ

hello how can i clean the ignition unit