วีดีโอ

Nobody cares😂😂😂

Look at that half inch of side to side play in that hitch.

Attempt 789💀💀

i can sleep a full 8 hours

Il beatbox when I don’t have my headphones in

I’m really good at making fart sounds and it fool everyone quite often

But what are the damn settings? I bought one and it has speeds 1-6 but the manual doesn’t tell you what those numbers equate to as far as oscillations per minute

Интересно, сколько спермотозоидов на этом диване?

looks so nice

Any suggestions on how to prepare Seadek prior to application of Shield? I probably have about 15 square feet of Seadek, how much Shield is needed? Will 16oz suffice?

What speed did you run DA while using Ignition?

BANG! NAILED IT! Enjoyed your video! Got a 2008 Triton that needs a little gelcote TLC and I HAVE NEVER done anything like this before. So I am bindge watching, LEARNING FROM YOU PROS, and assembling my repertoire of pads, compounds, etc. (Makita rotary and Groit's DA). Straight and too the point with REAL WORLD spanking results. (I like that! No B.S.!) BOOM! DID YOU KNOW, Kind Sir, that STARKE FINAL R compound can NOT be found ANYWERE? Yep, all sold out. Placed an order for a rare find of the stuff and they're sending me STARKE IGNITION, instead. So? I went ahead and got their LEVEL R and some ELEVATE to remediate and augment what "should have been" STARKE FINISH R. (I know right)? I'm not overly bummed out but DANG! Fantastic video. (Sub'd and your VERY FIRST "thumbs up"!)

Great video

Great video

How much did your boat and trailer weighed? Thanks

Hey brother could I ask you a question or possibly give you my email so I could pick your brain if you don't mind. I will sum it up then you I will let you decide. My buddy and me went halves on a 1974 18 foot del Magic. Has a brand new rebuilt mercruiser 250" 165hp. I actually verified and did start procedures and break in with a hose attached. It's nothing with mechanical. But for the fresh air pump for the engine area I'm so confused by the fresh air inlets. There are 2 facing forward and 2 facing backward inlets. The air pump only has 1 pipe attachment, and I haven't been able to find a proper diagram to route the hoses. This is one thing I just want to make sure I do right you know

gonna looks great when it's done.... while the Earth with all those chemicals going into will be left dead one day! but fu$k if the boat won't shine!!!!🤣🤣🤣🤣 🤪

Awesome❤🎉

Nice

Q es lo q le echas para q el agua no se quede

Super helpful video, thanks! What RPM do you recommend for the last two DA Polisher steps?

Is this a repaint ?

Very Nice

Nice man that looks great !!

Nice work

Great video!

Prevention is the key 👊

Where’s this store called Costco located?

Weird, but maybe vehicles that are above 9 ft wouldn't be able to pick up orders from the window

I got one from eBay for $47. Works great.

Nice

WAIT STOP THATS SO COOL!!

Kurwa ratatui

My Rice Krispies never sounded like that.

Why is the Toyota badge still on the boot lid?

Awesome armor protection …. It all about the spray tip I use .2 spray tip , but it must be thinned !! I use it on my tub inside and underside too . The trick with Raptor is the sanding !!!!!!!! Do not use 120 , I used 40 grit . I cut right through the pains for a good adhesion!! Very important to clean , sand, and clean again !!!! I use 20 percent thinner for inside tub and the under belly of the tub …. And yes I tested , 12 hours a little soft and hit it with hammer and it left a mark , I waited 24 hours and it was harder , after 48 hours it was hard as steel …. I painted my Rubi flame Red in Raptor liner , I use the 120 to cut the clear coat and then sanded it to 220 , wipe it all down in with tack rag three times …. Use a 2.0 tip paint spray gun , raptor liner was cut to 40 percent .. and sprayed in paint booth …. I’ve posted pictures on line Red Rubicon .. Came out great and 8 years of off roaring it looks just as good as the day I sprayed it … You can not find a better liner better than Line X But be warned I’ve seen the you tube … and 99 percent of the problems with raptor liner is the prep !!! Sand it , clean and clean it again , Spray it a light tack coat , then the second coat a little heavier , and the final coat , Yes I painted the tub three times !!!!! A tack coat , and two coats after ,,, you want it thick and you CANT DO THAT the first time , unless you want runs … Like my buddy’s TJ , Runs everywhere …. Don’t be in a hurry … My paint job is not like this paint job , It smooth and flat and the bitch shines too … My tack coat and the first spray coat it don’t same day , The last spray was done the next morning once the booth got to temperature…. I painted it in 80 deg atmosphere!!!

Tf is a jeep rapter

Mechanical failure

glad i just seen your video, what is your open opnion o this product as im a welder also but not a fan of those adflo helmets

sheesh

Do you worry about the welding fumes getting pushed up into your mask more, thats my only concern

👦🏿👈👨🏼🖕🥤

I see you like turtle wax as well! Nice!

Where can we get application

Cant even wash it now great

Niceee

🔥🔥🔥🔥

First time hearing this song and it not being in a meme

😶😶😶

🤘