วีดีโอ

Your absolutely right air guns are an expensive hopey. Keep having fun that's what it's all about. 👍

Which donnyfl mod is that? Sumo?

Pense que terminarias con tu mano completamente sercenada derecha y sin dedos 😅 gran trabajo beother

I went up, dont go up, it does absolutely nothing in its stock form. 2300psi is the limit with the stock hammer spring.

Man u are very bad shooter

O that is definitely a risk in public especially in Massachusetts 😮 I have had a couple of encounters with the police with a gun in my hand myself and it is definitely uncomfortable. Most average citizens have little to no knowledge of airguns so if they see a gun of any kind they freak out.

Kind of sad they omitted this from the manual

"Where did you get the coconuts from Fred ?"

Put silicone grease on the o’rings and the shroud will probably slide over them without moving them, I’ve also seen people put one wrap of electrical tape over barrel o’rings to keep them in place

Regulators are always increased by turning counter clockwise and decreased turning clockwise, and most regulators can be increased while under pressure but depressurized to decrease the pressure, also use Birchwood Casey Aluminum Black for those scratches, I had a few on one of my guns and it blended perfectly

Nice! Looks like a pretty simple gun I think you beat the manufacturer to making a video on this too

hey do slugs shoot out of the sortie? and which pellet is best for penetration through the sortie? in your opinion

I like that

Yours looks just like mine I got the .30 long barrel from Macavity website for $510 plus $20 shipping…. Then I got the scope off Amazon for $137 I believe…. A vantage 3-9x40 AO. Of course I have all kinds of rings on hand but another $80 on a few different brands of pellets…. And we’re already over $700 and I did it off impulse because it had just sold out on Utah airguns and it was still on pre order from AGD and pyramid and I just had to have it in .30. So far mine has served its purpose and hasn’t had any issues. I got mine on 9/7/24 and shoot it every day. I will say I was getting nice groups with a couple different types of slugs at first but now I can only get those great one hole groups at 50 yards with pellets. I suspect that the barrel might need to be cleaned… mine was super dirty from the factory also. And I’m getting about 18-20 shots from the top of the fill to my reg pressure. I have also heard and I see something in the comments about not shooting below the regulator pressure and to my knowledge that’s good advice. I haven’t owned a regulated gun before this either but I know some people with super expensive FX rifles that are regulated and they always say shoot from top of your fill to the pressure on the regulator. Of course the regulator is also supposed to be 500 psi or so lower. I’m not sure what the issue is but I believe Macavity arms is supposed to be making a video on adjusting the regulator. Pretty sure you have to degas the gun and take the regulator out of the rifle to adjust it but I’m not really sure how. I haven’t adjusted my hammer spring but based on my regulator settings and my FPS I’m guess it is either maxed out or close to it.

Who gives a crap about this speed and other cartridge nonsense? Every living animal on the North American continent has been killed by a .22 long rifle cartridge. It is how you shoot not what you shoot that is the key. My carry gun is a ,22 and it is plenty.

Seems like the debt will keep increasing after each step, but there is a limit. Everything has a limit eventually. I prefer to just work hard and put as much as you can to pay them off, not just the minimum but a bit more, otherwise takes too long.

i think it is interesting you are trying to find your velocity by the range at which the projectile hits a target. it is pretty cool. me i took time to use my chronograph and find the velocity at different regulater settings and make a graph of that for future use. course i am not using an internal reg nor this brand air rifle, i have aseveral aea airguns and i use the 52mm externally adjustable regulaters mostly. and an avenger but it works the same with both types and in all calibers. good content friend keep it up. my .25cal aea challenger gets similar velocity as your .30cal there and my .25cal has an internal reg too and uses 47gr hp lead so for the most part steps up and does what most of the .30cals do jts and macavity and brokock . i get 78fpe with a .25 cal smiles my .30cal gets over 130fpe and it has to use slugs cause it shoots them at 1051fps for a .50gr and sometimes faster and only goes dwn to 980fps with a 6gr hp. course that is my only .30cal a challenger pro long barrel. most of what i have is a higher caliber than .30cal enjoy your memories and the day

They let you do this in the park. I don’t think I’d do it where I’m at😂

Yea I just went back and watched and even paused it and I’m not an expert but I do believe it would be shooting better if that regulator pressure was lower. Ok I can’t find my manual but the box says 2030 regulator pressure and mine is right at 2100 I haven’t taken anything apart or changed anything… so somewhere between is where it should be

Keep it up brother 👍

I wish I can get one of the guns you have I love your videos 😅😅

I have a bunch of fam in Westfield, and Springfield Ma. I loved hanging with my fam over there. Most retired and went back to P.R. I'm next in a few years

I am dirt poor but weed rich lol , so I feel ya , awesome gun I just looked them up

Man, you're traumatizing that chrony. It's freaking out, and there are no witnesses around.

I'm watching and waiting. Just got mine and the reg is also set at 2800 psi. Haven't shot it yet. I wonder if increasing hammer force would help with the higher reg setting. Please be kind fellow air gunners...I'm a newbie! Thanks for the vid man. Sorry bout your chrony. I don't even have one yet!

Great story time

Love mine. Very accurate.

You seem to like the same air rifles that I do. Hatsan Bullboss .25 cal Hatsan Bully .25 cal AEA HP SS .30 cal I also have a Byrna LE that goes with me everyplace.

I look for gravel pits that are not in use to go shooting. They are usually fairly isolated, and the banks of the pit are great backstops. You might try locating one.

Sorry about your chrony. I just bought my first one and am paranoid of hitting it. Gun looks great. I'm debating between that one and the AEA HP Max 30.

Of course, I'm gonna give you an error message. YOU SHOT ME BRO!!! You looked straight at me and shot me. I don't know what to say anymore. I thought we were cool. I can't see anything anymore. I just feel the air rushing past me

I would be willing to chip in for a new chrony. Hopefully we get enough takers here to help. I would super chat you some. Just give us a prior notice cause we may miss it.

Super happy for you bro! I’d love one myself, I would love for you to find a spot where you can be comfortable man, hopefully sometime you will! I still enjoy no matter what

that a expensive prop now , man that sux , don't feel bad I see scott do it a bunch , good vid as always

It's not good too shoot it below the regulator set pressure it will hurt the reg I found out the hard way lol

Looking good! Poor Chrony!

I think when the coconuts are kinda young the shell it's not hard

Whats the little bipod you have in the back ,sorry about your chrony . Where you get metal mag from also?

Rip Chrony. Haha the gun certainly seemed to prefer the plastic mags. Very slick lookin rig homie. That suppressor is workin damn fine! Hahaha

That could be a Notos replacement for a compact more powerful gun. Although it is longer. Heard the stock is a bit weak and wish it had longer pic rails and also on the sides, would help in the tactical looks.

Bagaimana jika saya hendak membeli pistol ini.?

hey man i got a hatsan sortie that i CANNOT get to fucking fill! I put the probe in, cock it, and I start pumping and - nada. It builds up so much pressure that it will EJECT the fill probe! It's almost like it doesnt even OPEN the fucking valve? Any ideas? AWESOME channel btw man!

I've had mines for over month haven't even put it together yet...SMH lol

Since your frame is the shooting stand...just bring a small mirror and set up in front of you so you don't look like a convicted felon every 30 seconds watching your 6...

I'll have mine Tuesday the 1st. Can't wait

Beautiful piece, hadn't seen one without the buttstock before. It really is a great package. 🎉

Silicone oil is the best or even very thin amount of silicon grease on all moving parts works well, other oils seem to not work as well.

Fantastic explanation video you made, I’m putting a video up soon on my channel showing a way to get smoother operation of the pellet belt feed that helps stop jamming pellets and lighter trigger pull ect.

Your hats crooked bro

Good deal!