วีดีโอ

Great work! I can't believe someone stole that.

And den no slurpy slurpy on my machine

Работает ровно - вот только резкости не хватает - нужно зажигание чуть ранее поставить

Great video, thanks! I plan to replace the transmission cooler lines that are wrapped around the side of the radiator (they are rusted and I suspect they will start leaking any moment). Do you think they can be removed while leaving the radiator and condensor in place? Can you slide them up or down the side of the radiator?

Thank you my friend :)

Can you fix mine? Please! It’s got sun damage as well, I tried just replacing the top polarizer but it didn’t make it as clear as this!

omg!!! This is brilliant 👏 bravo thank you so much

Great instructions, thank you for sharing these steps. I will be doing this myself soon.

Don’t know about the engine but I dig the ROCK !

Whats the oart number for the lcd screen? Cant find it anywhere

А какой расход топлива

Saludos desde Puerto Rico 😊 le pregunto, ¿Como le puedo cambiar el cristal de el velocimetro? Es que esta todo agrietado por el Sol y no puedo ver donde marca la gasolina ⛽️

Me podriar mandar de como van las mangeras donde va la valvula pcv

how much will this cost and address. lol my odometer digits don't show due to the sun damage. Great work!!

Mate, genius!!!

Will you fix mine..great job guy!

That engine was designed by Suzuki and Daewoo in a Joint adventure.

GOOD CONTENT......BUT DAMN!!!!! GET A TRIPOD

Thank you for sharing

Thanks for the info it got me sorted 👍

keep it up, when this project will complete?

Where r you located ????

Paris

You are the 1st person l seen to replace a radiator in an S550 mercedes without removing the a/c condenser and oil cooler with the radiator. Great job!!!

Great job my man.

May you make another video, i stuck on removing the pcb

Thank you my brother

A digital kitchen weighing scale is about 0 to 3000g range. If any U tuber is doing such job for a Mercedes pls weigh the new vs the old engine mount. Drill a hole to empty out the fluid in the old mounting and weigh it again. Would be interesting. Thanks in advance.

Nice videos! I am working on a VL400 right now and I wondered if you can tell me which hose to connect to plastic fitting on the carburetor cap?

Didn’t show actual removal

Mad skills especially as it seems you are doing it in the parking lot. Can you tell me because I have to remove alternator, can I remove the fan shroud without removing upper radiator hose?

Please what is the total amount of fluid required to replace the old one ?

What was the problem?

did you have to program the new abs module?

Wd40 jam ! I love it 👍🏾

What about the wind ?

これをDIYでやろうとするのは素晴らしい(^^);

Mau pesan untuk Expander isa

This is a very detailed video for measuring and checking normal devices. However, nothing is fixed here. The voltages shown on "bad" device are normal. Mine was exactly the same and the device tested good when removed from the circuit. Nice effort, but you didn't verify this took care of the error. If you actually solved the ABR ESP problem, please update what was done.

Does anyone know if its the same for an s320 cdi?

I sir what website you use with our phone to know the cheap

I’ve changed my motor and resistor and still nothing.. I hear it running and stopping but it’s not blowing from the vents and I can’t turn it off and on… HELP ME PLEASE LOL

Was this a 4matic? Did you have to pull the axels to raise the motor. I am dealing with a 2008 S550 4MATIC

Very good tutorial for car AC gas charging. Please post ideal gauge readings in description. You have very good practical knowledge. Next time before posting the video write everything on piece of paper and practice atleast twice before posting your video. Good luck

I have the same error, same issue. I believe some sort of water got inside threw the hood vent and cause a problem to AC unit (blower). Your explanation is so clear and I hope I can fix it. Thank you

Are the motor brushes getting too short?

I have a 2002 e320 and need to replace the tensioner pulley and i notice it has a little groove in the middle like the second pulley you replaced, but when i look at replacement parts the pulley is smooth. My question to you is that normal to replace a pulley with a groove in it with one that is smooth, any feedback would be appreciated. Thanks for posting

hey, I am trying to build this type of foldable carport for my BMW F10. Can you share the blueprint with me?

Wow! Great work

Good job