วีดีโอ

hi sir jugi may I know what g903 Switcher did you used? my left click is not functioning also.

Hi there, great video! What would you reccomend for a 3060ti Vision? I cannot find the information about that thermal pad size anywhere, any help would be massively appreciated 😁👍🏻

Hi there, I have the Audi Allroad V6 3.0 Quattro 2011, every morning when I go to start my car the rear suspension is right down, I start the engine and both the yellow and green lights are flashing, I rev it for a minute or so and the yellow one goes off as the car is lifting, I slowly drive off and after a few hundred yards the green one goes off. I drive round for a few miles and it stays level, I then park up for the night and the next day the rear is down again, any idea what the problem may be? I have had two mechanics look at it and both could not find any leaks, the second one said there was a fault on the computer, which he cleared, but no leaks, any idea what is going on? Thank you Gareth

God, this is slow. A lot of posturing but not much actual repair. 😊

Thanx for the video! I'm not so sure that it is recommendable to let it stay in the ultra sound for 30 minutes. I clean my production boards in alcohol (45C temperature) with a drop of detergent for 4 minutes, rinse them shortly in distilled water and blow them dry with compressed air. In your case the contaminations are of another sort but 30 minutes still sounds over the edge. And Jugo... 18-250 is the focal length (in mm)! 3.5-6.3 is the "speed" (aperture) of the lens:)

Very helpful, thanks!

do you have video how to open the white case? i want to clean the fan

Est-ce que les suspensions pneumatique provenant de chez Maxpeedingrods sont de bonne qualité ? Il y a beaucoup d'avis positif comme négatif..

As a mosfet I use cs1n60, and it's fine too, bought on aliexpress

Sometimes it fails, the Hr1000a, if the: mdf9n50B fail

can you update the link for the switches? thx

use pogo pins to read data from chip?

In my humble opinion any comparison of budget soldering tips without comparing them to the original Miniware tips, is not a genuine evaluation.

Saya punya impact bosch gds18v-400 rusak kena air, kira kira apanya yang rusak ??

Where is the warranty stiker in this gbu. i mean in all vision gpus

What a shame the picture is shown for an imac 2017, but you remove the efi from 2013

im confused there were grey ones under the small blue ones but the description says the blue ones are 3mm someone help please

Hi great video! But what could kill all 10 cells from pack? It's very strange, did you try to make a jump in each individual dead cell with another new one to try to revive?

On my charger are burnt: T1, T2, R7 and R13. Does anyone have types from?

hey ich habe auch so ein ähnliches Problem nur dass es bei mir die Luft nicht ablässt oder verliert. wenn bei mir mehr Gewicht drauf kommt dann beginnt es bei mir zu blinken und ich kann es nicht mehr einstellen aber die Luft hält es ohne Probleme. nun habe ich verdacht auf dieses Bauteil oder die Niveausensoren ich weiß leider nur nicht was genau die Ursache sein könnte und das nervt mich langsam echt extrem. was denkst du ?

how did test the compressor? And how did you know it was the valve block? How did you test it?

¿Cuantos kg pesa?

thank you for the help! 😄

where did you buy the replacement chip?

i am trying to do the same thing i have multiple broken one's im taking apart for parts and the plasticy body is driving me nuts and seeing video of the struggle makes it worse

bro i need your help i have an audi a8 2010 and i have problem with air suspension... I was doing service and mechanic forget to lock it up and after some time my car start geting lower in front end when i leave it over night.. Sometimes its fine it stays. Also sometimes it gets lower after only 30 min and as soon as i start my car it get at normal height. I put my car on diagnostic and it only shows one error c11aff0 but when i drive it i have no problem car drives fine and no strange noises, also when i turn off car air compressor stop aswell.. Can u please help beause in my town we dont have good mechanic and i really need help :)

thank you so much! i just restored my G903 using your video! 🙏

Are all the pads 2 mm thick?

What is the name of song?

Have you heard of the conversion shocks absorbers ?

My Bosch GSR 18V 2Li is smoking and sparking. If I change the whole motor will it fix the issue? I am not that skilled to do all this delicate work with cleaning parts and pieces. Thanks

You have your own business to do this stuff? I have the 1080 version and this needs to be done 😊

Jais un problème tout les matin je me retrouve la voiture un bat

Hello everyone, I must add that sometimes the small transformer burns out

great video

where can i find a new BMS for Bosch Pro Core 18V 8.0AH Battery

Hi please my cooking chef is having an issue. How can I reach you to help me solve it?

Ok thank you so much for the guide!!!Also I fallowed your steps to get my EFI chip out of my late 2015 iMac… and I can’t get the Chip removed. I’ve been fallowing the steps idk how long it takes to remove the chip… I’ve been doing this for 15 minutes now and off, and it won’t come off!!! I’m worried if I go any longer I’m going to ruin the computer.

I don't like the music sorry

What a piece of garbage engineering. the varistor and fuse exploded on mine 8:50 A SMD resistor on the other side of the board also exploded 11:46 I think its the same, just under a cap It broke after 3 months of use, I hope bosch waranty fix this.

Je ne sais pas si tu liras ce message j'ai un problème sur une perceuse Bosch pro à batterie le mode percussion ne fonctionne plus auriez-vous une idée de ce qui pourrait poser le problème

For thouse who can't remove the battery: you can *very gently* carve out piece of plastic just above the green PCB with something like box cutter, and then *carefully* shove the same box cutter underneath.

horrible music. keep it quiet n just have a topless shiela walking around.

Pulling out the CR2032 battery with needle nose pliers can finish off a borderline battery because it creates a dead short between the positive and negative terminals. You should wrap the ends of the pliers in electrical tape before using them to pull the battery.

can you remove the chip and not put anything in place of it?/

Is it possible to stack 2 of 1mm pads to make it 2mm?

Thank you very much! Your guide helped me a lot while disassemblying mine, and after almost three hours of work (there were a few side quests...) it works!!!! Thanks a lot, indeed!

i Recommend this video!!!, such amaazinggggg

Wie viel Bar muss der kompressor denn bringen ?

Meiner pumpt sich vorne nicht schnell genug auf und geht dann in Fehler