- 2
- 24 220
Leonard
Indonesia
เข้าร่วมเมื่อ 29 ม.ค. 2014
Cim
Creality Ender 3 V2 (upgrade display cover)
www.thingiverse.com/thing:4567915
by : Cim
this my first printing, and there is a slight revision in the download file.
Im printed using PLA filament.
can be downloaded at thingiverse & myminifactory. @leonard_guitar
Have fun 😊
by : Cim
this my first printing, and there is a slight revision in the download file.
Im printed using PLA filament.
can be downloaded at thingiverse & myminifactory. @leonard_guitar
Have fun 😊
มุมมอง: 8 461
วีดีโอ
Anet ET4 upgrade direct extruder
มุมมอง 16K3 ปีที่แล้ว
www.thingiverse.com/thing:4583702 By Cim - V.2 This design version two. Still using standart part from anet I'm just upgrade the fan for filament with the GDSTIME brushless DC Fan 24V/0.05A note : *reverse the ( 6 pin ) connector extruder motor *use shock absorber motor stepper *use PETG filament another project @leonard_guitar please like & subscribe for support my channel 🙂✌
Hello 2014
OK a couple of warnings. The bottom mounting hole is not correct, you will need to drill a new one. The short piece of bowden tube will vary in length, I used approx 70mm not 65mm. You will need to purchase another stepper motor cable as the original is only 90mm in length and will not reach.
link the original model, not the stl you destroyed, bud
Why would you revise the model to remove screw holes? now what holds the case together?
Les supports qui s’enlève aussi facilement j’ai jamais réussi 😅
Hi, great video. I would like to know if is it possible to change the motherboard to mks mini or similar and use with the original settings. Could anyone help me?
Of course you can change the board....question is, why would you want to?
Excelente video amigo, pero surgió un problema, el carro del hotend se me desplaza unos cm hacia la derecha al aplicar el home, ¿sabrás a que se debe?
I want to the same thing to my Anet A8 V2.
Better to change the stepper motor for a pancake one so it's lighter.
Hi, does it work on et4x?
Yes. U can check the model before
What cable did you use to extend the motor s cable or the actual cable It self
You can use any tipe cable to extend. But dont forget change the port. See video 5:35
Do we need to change the wire or just turn other way??
Yes. Must change the cable position. See in the video 5 : 35
And. U need extend the cable .
Isn't it too much weight for the axis?
No problem about weight. I have printed alot with this
What is the benefit of doing that?
Good for TPU filament.
Good job sir, does it work for ET5 as well?
I am not sure. but try to check the specs. maybe the same size et5 with et4
Do you have stl file?
www.thingiverse.com/thing:4583702
Did you notice any precision reduction on X axis because of the moving mass increase?
yes, I have considered it in my design. printer parameters can be seen atwww.thingiverse.com/thing:458...
Is it a normal et4? Do you have tmc2208 on the mainboard?
Yes. This my anet ET4. The cheapest tipe. Not tmc 2208
I have anet et4 pro and It's extruder continuously making clogging noise maybe this upgrade solve my problem
Yes. Lets try. 🙂. Get attention the temperatur and speed. Good luck
If it needs upgrading; you need another printer: m.th-cam.com/video/gCPNr_Qf9vA/w-d-xo.html
Anet ET4 better. And more cheap
@@leonard4053 So you did not watch the review in the link, that is a review of the Anet ET4
@@RuubRoyce i think, better you contact the Anet company, tell you Anet problem.My anet different type with yours.
@@leonard4053 I did. Anet told me that the seller I got it off from aliexpress, was a legit seller and that the product sent to me is an official Anet product. I also asked them how or why or if there are two different types of ET4 printers, however they didn't answer that question yet.
My anet is the lowest type. (Blue color) without auto level.
did this stop the clogging issues? i cannot get some of my et4's to not clog and it is the most annoying thing ever. i tried using the one fix with the washer and the separate tube in the hotend to get maximum pressure between the nozzle and the tube and it just jams inside the pfte tube now.
Hi friends, for clogging problems, pay attention to the temperature at the nozzle and the printer speed. Each type of filament has a different temperature. if a blockage occurs, it is not hot enough or the speed is too fast. Direct extruder, gives good print results. especially when we use TPU / elastic filament. Check again my print settings, at Thingiverse account. Good luck
Hi! I had the same issue with clogging hotends and could not for the life of me fix the problem. So I ended up sending my unit back to the store I bought it from to have them check for problems and apperently there was a manufacturing problem between the nozzle and the tube. They replaced the hotend with a spare. Haven't had a problem since.
best thing i ever di to my et4
Have fun buddy
Does this work with bmg extruder?
This is for anet ET4 original extruder.
Is it compatible with Anet Et4 Pro? Cheers
I think, the specifications are the same.
How does everyone but me get their support to come out in off so easy
Have you calibrated the steps somehow ?
Yes. Every time print. Better calibrate before.
Bonjour. Super réalisation ! Je vais essayer sur mon ET4 . Merci
Very very nice my friend. Ling for this item?
www.thingiverse.com/thing:4567915
Hii, nice job, i have a question, don't you have sensor-filament (end-detection) anymore?
hi. I removed the filament sensor. but if you want, you can use it. with a little modification. maybe I will discuss in the next video.
@@leonard4053 Yeah, i would like to see what you did, thank you :)
hey excellent could you put the link to download that piece I have a printer of those and I would like to make that modification 😊
Hi. About 2 days. U can check my account Leonard_guitar at thingiverse & myminifactory. I will upload it. 🙂 Dont forget to post your result print.
You can get now the file. 🙂
Wow kreatifff ini... Mantappp ko
Thx 🙂
Nice! Good job