วีดีโอ

Thanks

I think changing the Rate under UBX > CFG > Rate, will change the rate for both UBX and NMEA. I haven't tried this though.

Which LED, I have some nano boards with blinking LEDs and some don't. If you mean the GPS module's LED, they will blink when they receive a valid GPS signal.

@@3DElectroTech neo 6m, I've waiting Up to 1 hour more, but still not blink. Pls helpp

Use U-Center application to make sure you are receiving information from your NEO-6M. The information will start coming immediately and you don't need a Satellite signal to check. This check will insure that you have a working NEO-6M.

@@3DElectroTech do u have the tutorial video? I try to use U center but the port isn't blinking(green)

- Which Arduino are you using? - Which Ublox device?

Glad you like it!

I am glad it worked well for you :)

Thank you very much for following my videos, this inspires me greatly. The Github's project page contains the latest code github.com/Boynet006/NEO-6m_Speedometer The upper part of the code sends all the configuration needed to make NEO 6M work without the need to save the settings. So, every time you power up your device, the neo 6m's configuration setting will be sent and everything will work normally. I have had some issues with some of the modules trying to save some settings like baud rate using u-center, they might be defective modules. Do you have M7 or M8N? they can reach up to 10 Hz with little code modification.

Thank, Yes we can communicate through email.

Thank you

Try swapping tx and rx, Try reverting to default settings, if there is solder paste on the terminals it could cause this issue, make sure the terminals are very clean using rubbing alcohol.

Check out this video, it might contain part of the answer. th-cam.com/video/Ao5XRtd-RAA/w-d-xo.html You don't need to program NEO 6M to receive NMEA, it does that with the default settings. If all that doesn't help, please let me know.

In the latest project, we are using a bigger screen and that makes the numbers larger. Check out this project, it is nearing the end. th-cam.com/video/Qg0L3f6gY50/w-d-xo.html

Making the screen faster is doable, but if you mean the 5Hz refresh rate, that is the limitation of U-Blox NEO-6M GPS module.

Thanks, What can I do?

@@3DElectroTech How can I contact you? Are you on whats app or instagram? Thanks

@@3DElectroTech Where can I contact you?

​@@peterlaverty9397My email is boynet006@gmail.com

@@3DElectroTech Eailing now thanks

Glad you think so!

Thanks

At the moment, I don't have a tutorial that does that.

Yes, there is a final product, the one I am working on now. In that project, we will be making our own PCB. The below video shows an introduction of the project. th-cam.com/video/Qg0L3f6gY50/w-d-xo.html

@@3DElectroTech cool

Thanks for the comment, I honestly don't know how to make it work on the esp32 wroom32.

This video probably has the answer to your question th-cam.com/video/YGVc9rjBIHY/w-d-xo.html

Thanks :)

Check out this video th-cam.com/video/JGG4TcA6U-g/w-d-xo.html for the performance of NEO6M configured refresh rate 5HZ, I have tested the NEO-M9N configured refresh rate 8HZ and it works great. If you see the documentation for both, the maximum update rate for 6M is 10HZ and for M9N is 25Hz. As of now, the code is not optimized to get these results. Check this video for the final product that we are working towards th-cam.com/video/Qg0L3f6gY50/w-d-xo.html

The comparison was between Racelogic DriftBox 10Hz and our homemade NEO 6M 5Hz Speedometer

@@3DElectroTech i watched the first video and i see it works really well. I guess i will buy some 6M to tesy but since its a discontinued product they are most probably fake. Going to watch the second video thank you

@@acelyasamsan6960 I don't think the one I was using is Guanine and I purchased most of them from Amazon and Aliexpress. They work fine for what we need :) That is why I often buy more than I need.

@@3DElectroTech Well if the fake one works like that all good for me too :) now i will definitely buy it and give it a go. I also need to figure out about odometer, according to chatgpt if i have GPS coordinates it can be calculated. I guess i will try to do it once i get the module. Thank you

Is there a specific upper and lower control arms, you are aiming for?

Yes, as every USB supports 5 Volts

Could you watch this video, because, I think it has the answer for your question th-cam.com/video/YGVc9rjBIHY/w-d-xo.html Please, let me know if it does.

You're welcome! :)

Thanks 👍

No problem!

Glad to hear that :D

Might be a connection issue, check your Ublox with U-Center application. Try swapping RX and TX. Sometimes the breadboard wires can be loose.

It will communicate directly with the GPS module, without a sketch, just the wiring.

@@3DElectroTech tanx sir.

If there is a way, you can share more details like pictures and diagram. We will try to find a solution.

You can find everything on Amazon, but you know they might be fake. I am currently working on Guanine M9N from www.sparkfun.com/. I will upload a video once I finish the code.

The one in the video is Neo 6M v2

@KrauseOllyKrause Check out this video It probably has your answer th-cam.com/video/YGVc9rjBIHY/w-d-xo.html

This new video has the configuration for NEO-M9N. I hope you like it. th-cam.com/video/X7-P1UYxRHs/w-d-xo.html

Which corner exactly?

Left top those 2 lines which are rotating...

@@sanjuk2325 The left one shows that the screen is working and the right one rotates when you are receiving updates from NEO-6M

Thanks for liking my videos :)

Thanks for your kind words