![Socal Stucco Repair](/img/default-banner.jpg)
- 6
- 29 896
Socal Stucco Repair
เข้าร่วมเมื่อ 22 ม.ค. 2015
Stucco Repair Specialist
Stucco - BBQ Smooth Coat with trowel marks
Cinder block To Santa Barbra Smooth Finish.
- Spec Mix Cement One Coat, then floated with hard float.
- Two coats of Omega Smooth coat, first coat floated with hard float. Then apply second coat and trowel down with light mist of water as it drys.
- Spec Mix Cement One Coat, then floated with hard float.
- Two coats of Omega Smooth coat, first coat floated with hard float. Then apply second coat and trowel down with light mist of water as it drys.
มุมมอง: 17 384
วีดีโอ
Stucco Electrical Panel
มุมมอง 6K3 ปีที่แล้ว
Stucco repair Electrical panel From beginning to end - 60 minute paper -Lathe wire -Caulking - Rapidset Stucco 3-4 scoops -Spec mix Type S -La harbra 16\20 Sand finish with Skip trowel texture.
How to Stucco Repair- Small patch Tip
มุมมอง 2913 ปีที่แล้ว
Tips on How to properly waterproof and Lath a small patch the correct way. Learn how to do it yourself! This is great for a homeowner. Materials- - Stucco netting/ mesh wire - roofing nailed/ furnails - 60 minute black paper -
Keep practicing 🫡👍🏻 On your final smooth pass you have to time it just right go wider longer passes. Do not over trowel to avoid burning blemishes & short trowel marks. Lay it down dont over burn with trowel. Your trowel marks tell a story. None the less 💯 👍🏻
Nice
Nuevo suscriptor saludos desde frontera la Mesilla Guatemala 2005 California
No good my finished have sharp clean corners. Perfectly even smooth coat. No trowel marks.
Nice job
As a high end Plasterer/plastering contractor we put a tight tight base coat then wait till tacky a put a another coat and get as smooth as possible then let set up and trowel down being careful not to create burn marks only the best plasterers in pebble beach Carmel high end work at its best and being clean not to splll any material
My expirance is that most santa Barbara finishes should done differently. #1 bigger trawl, bigger hawk, corner bead shold always be applied , let brown set 2 days' application of first caot with a rubber float , and finish coat passing over only 2 times . Look at proper spacing of texture to connect texture, the flat surface should connect all evenly. Finish one side at a time.
Im here tryin to see if i can pinpoint where water might be leaking into my panel. have the same panel combo in exterior and some water gets in , slow drip from where the cables drop into the breaker side of the box. wondering if the drop-down cables might be trickiling water in since they dont have a correct drip line.
*Nice work, can you please tell me the proportions of the rapid set and spec mix also the water just for that space? (Looks like you had a bucket full which you didn’t use?) Also the dry time before floating? Oh and can I just paint it over or do I need to do a color coat? (I have the paint already)*
How come no blue weld Crete bonding agent over blocks will pop off over time guaranteed
beautiful ❤
Can you do this on permabase board?
Awesome work I’ve seen others lath the corners so they aren’t waive
Got to get the block wet before first coat.
Bro Im a solid plasterer from New Zealand. We dash our walls first, just wondering why you guys in the states dont.
Good work
🔥💯
Who would you have paint?
Good looking out homie
Looks good. Why didn’t you use flashing?
nice work 👍👍👍
Wall A/C to mini split install???
Looks like it dried on you a lil too much and burned the wall you can see all the trowel marks maybe next time have an extra guy to help out
What mixes do you use?
What you u don't have old paper? I ripped mine out when u did my electrical panel. Not knowing any better
Ok
Good video....BUT should have misted the cmu block wall for optimum strength/connection of stucco before starting.
It matches what was up there , 😊
Nice job. I’m new to stucco a question I have is can I put smooth stucco over rough stucco that seems to be painted? If so can you please explain the steps for me. Thank you
You have to pressure wash, use bonding glue, skim coat a brown 3/8-1/2 inch then do your finish coats
Absolutely beautiful, like and subscribed, thank you, im getting involved in more stucco patch work, thank you
You a fan of the pool trowels for smooth or you’d rather stick with the square trowels
Whack music. How this song matches your work is confusing
Looks great! How much does it cost?
Where’d you buy this omega smooth
Good video
Thanks for your time man!! What's the name of that caulking that you used there?
When you say you applied on there did you mean you applied the La Harbra 16/20 to your new stucco patch to match the finish?
Yes, I applied the La Habra 16/20 over the brown coat then I’ll let it dry in about 5 to 10 minutes and then skip trial the texture on there with the same 1620
Cuanto se cobra un trabajo como ese
1500
Cuanto cobras por un parche así
$450
@@Socalstuccorepair Hi, are you available to come to Norwalk, CA? I just had an electrical panel upgraded. Please let me know.
How much did you get payed ?
1500
Looking good amigo, good job and clean 👏
Lucks good Amigo 👍
I was the 100th Like on this video!
Thank you brotha means a lot I appreciate it.
Nice!
More videos please main panel ones
More videos
Spec mix cement the same thing as Spec mix mortar?
Yes sir. I use spec mix for patches a lot. But I like to add my touch to the mix like glue or fiber and both sometimes
Why didn’t u wet walk first bro , gonna come off in 1 year
Hey boss very nice job..what number did you use for final finish 20/30
I used 20/30 for the first coat, then Santa Barbra smooth on top of that but extra thick, to thin will leave alot of burn marks by the trowel. The trowel matters too.
i can answer for you? santa bárbara is only 20/30 i guess, that’s the finest finish material for smooth of la habra
??? I live in sun City ca I replace my very old 1964 electrical panel with nice and new one in a different location, my ?? Is can I cover up the old outdated one 🤔