- 19
- 21 416
Chris Tate
เข้าร่วมเมื่อ 4 พ.ย. 2011
A little bit of random stuff
BMW M240 G42 gen2 B58 Burger charge pipe/bov install with sound clips
In this video, I go over some things that I feel where left out of the Burger blow valve charge pipe installation instructions. I also, tossed in  some clips at the very end that give you a little idea of the sound. It sounds much better than what I’m able to capture on the phone.
มุมมอง: 337
วีดีโอ
2005 C6 base Wideband power and glow-shift dash pod install
มุมมอง 152ปีที่แล้ว
In this video, I show how to obtain power for a NPP box and or a wideband. Also, how to run the power wire and install a glow-shift gauge pod on the cluster. 
2005 C6 factory exhaust mod on automatic with cats “cleared out”
มุมมอง 1622 ปีที่แล้ว
2005 C6 factory exhaust mod on automatic with cats “cleared out”
Dyno of cammed 17 ScatPack with a Procharger on 12# boost
มุมมอง 853 ปีที่แล้ว
2017 Dodge Charger Scatpack 6.4 392. Mods: MMX NSR Stg 3 blower cam, MMX forged internals, Procharger p1sc-1 race front mount intercooler, Tial 50mm bypass valve, FIC1000cc fuel injectors, Fore hat with single TI267 fuel pump, factory fuel rails, factory exhaust manifolds, Stainless works castles down pipes, Carven x pipe, and rear resonator delete.
Dyno of cammed 17 ScatPack with a Procharger on 12# boost
มุมมอง 513 ปีที่แล้ว
2017 Dodge Charger Scatpack 6.4 392. Mods: MMX NSR Stg 3 blower cam, MMX forged internals, Procharger p1sc-1 race front mount intercooler, Tial 50mm bypass valve, FIC1000cc fuel injectors, Fore hat with single TI267 fuel pump, factory fuel rails, factory exhaust manifolds, Stainless works castles down pipes, Carven x pipe, and rear resonator delete.
2018+ Dodge Charger Smart Access Cable install
มุมมอง 16K4 ปีที่แล้ว
This video walks you through step by step installation of the Smart Access Cable for (only) Dodge Charger. This cable is needed to gain access to your 2018 OBDII for tuning. There are multiple videos for Challenger and not for the Charger. You do not have to pull the radio or center console in the Charger like you don in the Challenger. This took about 5 minutes start to finish and only thing n...
How was your experience in using it? Any issues like boost leak or mechanical issues?
Thank you for this, will be installing mine tomorrow g42
No problem 👍
Roll jam Sam kamka
U could have just used a adc 2011 cord and plugged straight into the star connector but yea good video.
Thanks for the video that’s one of the best I’ve seen for accessing the module
if you have the access cable you don’t need to unlock your pcm ??
No you need to do both
Esto me sirve también para poder leer con escáner de OBD2 cierto ??
Does it stay on there or when your done tuning do you take it off?
Just leave it in case you need to make changes.
@TaterSalad83 thank you
Leaving it does half the job for someone stealing your car.
@@squaddlife 🤫
Any cels?
No
W guy 💪🏼
Thank you for the detailed explanation 👍.
Hey. Do you know anyway to get the Uconnect features like performance pages and stuff back on now that 3g is canceled
Yeah you should be able to call them and you can buy a dongle that plugs into your obd2 port
AFTER PLUGING THIS CABLE, WE CAN READ THE VEHICLE ECM SOFTWARE WITH THE HP TUNER AS I KNOW.. BUT IS IT POSSIBLE TO MAKE CHANGES TO THE ECM SOFTWARE AND THEN WRITE BACK TO THE VEHICLE AGAIN? CAN YOU GIVE INFORMATION ABOUT THIS TOPIC? THIS SHOULD BE THE MAIN ISSUE...2018+ CHALLENGER 3.6
The computer has to be unlocked by HP tuners to be able to write/change settings. The cable just unlocks your canbus “star network” to be able to communicate with the ECU. You can read it however it’s locked and will need unlocked to be able to write
Did the same on my 2020 rubicon. Gonna be ordering a aftermarket blowoff valve and cold air intake soon.
What's the point? Does it improve performance?
Sound
Hi did you let the cable on the car or you use it temporary till you make modify for the car because I didn't understand you
Leave it
...so what is the mod?
Just a hose unhooked with a plug
Ok explain…