วีดีโอ

The quick release is a fantastic I didn’t know was available and perfect since I don’t want to solder

Thanks for the shout out! Also the step by step! Its hard to get to how to videos so always happy to see others share how they did it. -Imperial Tech Shop

Great video!! This will be my next haslab pack upgrade!! 😁

THE AUDACITY!!!

I bought the v-3 diffuser "dirty look" 👍🏻👍🏻👍🏻

Where can you get the connectors?

It’s looking good 🚫👻

For a moment, You looked like De Niro talking about Ghostbusters

I just replaced the hose for a real cloth one and soldered the wires back together ,ill have to add the clinko connectors myself now though.

Does bracket A go on the right side where the N filter is located or is it bracket B?

Any suggestions how to split into one of the JST connections on the ninja tunes board to power a few low lowered LEDS? prefer it to come on with the pack and not have several battery packs scattered around.

Once all the brackets are aligned with the holes will it stay aligned if you need to remove the mobo? Or do you have to start the alignment process again if you remove the mobo for whatever reason?

Guys, hair dryer and WD40. Those are the absolute best tools when it comes to sticker removal. Always heat the glue up and you’ll find it’s so much easier to get the stickers off.

Ever tried using lighter fluid to lift off stickers? (Not lit obviously) Much quicker - will lift off the whole sticker with patience and allow the sticker to be reused (not that you wanted to do that) but will not rip and leave paper or glue after (chemical in the fluid breaks down the sticky stuff) great vid!

Came out awesome, and Mack’s labels are amazing and bring out the pack more. I had fun weathering mines

Mines came last week. By my A bracket came bent hammering it to straighten it out. Video is very helpful

You guys are so cool

I know you mentioned you had. 10/32 screw. Do you remember where you purchased it? Bout to get the clippard disk cover

Okay, so my pack is still completely stock on the electronics side. I'm not that good at modifying electrical components, and I want to keep my pack stock for the most part. So, my question is, will the stock board in the pack, along with the batteries, be enough power to allow this speaker you've shown to work?

I tried attatching the chrome connector without the cover and stripped the screws trying to get it close enough to the pack 😔

Thinking about doing this mod but I’m not sure if I want to deal with the headache of ripping out the fake copper wires. Real Clippard valve is already installed I just gotta get the longer screws

The editing of this video is superb! Makes me want to play the game even more

I don't like the connector they should have separated it instead of being together makes it easier to work with

I was onboard with this until the actual mounting it. 😂 WAY too much messing around for the sake of having a metal back. Credit to you guys but not worth the hassle for me.

The 5 rifts from that overlord say otherwise

I loved the snippets of Real Ghostbusters music you used here and there. Nice touch.

So, what I did, using the same talent cell, was to take the wall in the "snack compartment" and trim off from top of the upper screw hole and up, and then use double sided tape to tape the talentcell to the wall separating the electronics board from the rest of the pack. I did have to to trim off the top of the battery compartment, but kept the rim with the the gasket. From the outside of my pack you would never know I'm running a talentcell, but I can access it from the "snack compartment" door. I have both the talent cell, and a JBL Go2 speaker in my "snack compartment"

For the ALICE Frame nuts; If you want to get them from the hardware store instead of harvesting them from the OEM motherboard, you will need the following metric nuts: • (10) M6 x 1.0 & • (2) M8 x 1.25 I recommend grade-5, nylock.

With the solderless connectors you can just buy the same plugs that go into the packs board and just swap that out. No snipping just plug and play.

I like the full silver cycle atron you did

I'm wanting to mount my 84-afterlife and vibration switches from the Cyclotron to the lunch box. Would the same technique be used for those switches?

I feel if you don't swear or cuss at your pack while doing upgrades, mods or build then it's not a proton pack. My pack is a son of a Bitch and it knows it. Looking good my friend!!!

Looking good so far!

yet again please learn how to say clippard 😭

W

That was awesome!

so, these speakers will work with the stock sound board and power of the haslab packs? Will it be compatible with a ninja tunes board if i upgrade that later?

Gotta say, I love this series. However. You do know you’re horribly butchering Clippard, right?

My pack #5 is going to have the frozen empire bumper but it being the same color as the rest of the pack

Love this so much it’s so good to see someone not exploiting their cat on TH-cam great job.

When is the full video coming out?

Personally its looks good its gives it more characters in being used 👍🏻👍🏻👍🏻👍🏻

They ripped everything including the decals off so that it wouldn’t be so easy to identify, of course..

I will definitely be sharing the news with my franchise, we already made a post about it a few days ago, and will be donating as well!

Oh man, I can’t wait to install mine. I’ve had it sitting in the box for about a couple months now. Also thank you so much for this video!

What copper wired are those?