วีดีโอ

I got a e-bike conversion kit off Amazon for 130usd with battery

Thanks for the video. My 2008 Honda TRX500 recently had a big jump in the oil level and it looks like water got into the oil. I'm hoping that the problem could just be a broken seal at the water pump, is that plausible?

Them chicago dremmels are trash used it twice an had to fix it both times i had the corded one tho

All these Honda rubrican machines have this ticking noise I’ve seen brand new ones with it it’s just how them moters are

I got a lot of the yellow batteries when they were free and still have some left They work fine in real low drain devices like remote controls and low lumen incandescent flashlights. I just make sure to look in the battery compartment occasionally for signs of leakage (usually the yellow label will start looking different as it starts seeping) and haven't had any issues.

What seals did you order?! Cause I can't find the right ones just chinese stuff on ebay

just get your buffer high-speed buffer or something of that sort get you some micro finishing compound go ahead and take the oxidation off in seconds and buff that thing and Shine the actual plastic . then go ahead and do the same thing with some wax afterwards it look like it came out of a showroom simple or you can use a DA sander with 220 on it either way

the dumbest thing I've ever seen. only reason it even look shiny is cuz he's missing oil with it

Fyi.. for most winches a company makes a remote controller to mount on the bars

Read on a forum that some owners have had the valve tick right out of the box. Saw numerous suggestions saying setting the gap to 0.004 instead of 0.006 fixes it.

the wire wool is a BIG mistake

what wheel did you use and or list in the description

If you have to use a hammer to remove an axle shaft ALWAYS put the castle nut back onto the axle BSCKWARDS to protect the wheel hub's threads And the castle part of the nut.. BEFORE hitting it. You'll prevent the axle from getting thread damage. The nut gives you more surface area to strike and wont deform the end to where you cant get the nut back on.

Rush it back to Harbor freight

are you canadian by any chance?

I had mine for a few years purchased used from HF. Used it today and it started smoking.

Why dont you like the charger?Its small ,doesnt take up much space and WORKS.

How big are those fuses you spliced into the harness

I personally like the chrome handles better.

Replaced the pump and still leaks on same front bottom bolt ,can't figure out why?

Where did you get the mount

Love my HF tool boxes/carts. Awesome for the money.

Mine keeps overheating should I do water pump or the thermostat first?

Is this water pump same for a trx foreman 500 2012 ? If so could u send me the link where u purchased thanks

Do any of yall think it would be plausible to add a brushless motor from on of the tools onto a bike as well. Just a random idea I had

I’m using the Bauer rolling box and the crate as a camp chuck box…

This is a very good video. The only thing that is missing is how many sanding pads you used during each process. Just use one sanding pad in each step out of the number of pads provided.

17+-Wh per mile is pretty good.. werry same performance as high grade e-skates.--.

So I hooked my son's hyper 350 the way you did. Both 6.0 Milwaukee batteries were fully charged. After my son's first ride he checked the batteries and they were flashing only one cell. Have you experienced this before. The batteries are brand new.

You dorks are talking about the guy being a nube for not breaking the comprrssor in, older units ran for decades without any break-ins. These things are built to the bare minimun, and you fail to realize that sh*t these days arent meant to be used and abused like the older units. Get your heads out if your asses and stop blaming the user and put the blame where it belongs. This goes across the board on all things manufactured.

Where do you buy one at?

I have to do the hood of my side by side. It’s going to take a long time

Great video 🎉!!!!

It’s junk I used it for my bike tire and when it reached 35psi it cut off even tho my bike tire need 50psi

If you check them regularly and can check the gaps hot, lower the gap more to quiet them down why put up with them noisy. There only has to be gap so you don’t burn a valve instead of .15 set them at .11 etc

Need a handkerchief?

I purchased this used 2 times blowing up balloons the engine blew. Of course 90 day warranty was up. Paid $ 119 with coupon.

The lat part is easy it is opposite thread spin right to unscrew left to tighten U can weld a bit of box section to it and use a pipe wrench had to do this because I tightened the crap out of it screwing it the wrong way hope this helps

That screw driver is clearly not designed for that kind of use.

Hi, what battery did u use? What it the voltage? And how much Ah? ;)

Have fun with those $30 k + box loans

Need an up date on new high output batteries

Any problems with the battery's? I've read comments on other videos people burning the battery's.

Ha the casters you showed in the ad for $17.99 are not the ones you were putting on the ones you were putting on are $7.99 and are rated for less weight they are rated for 330 pounds and the $17.99 are rated for 375 pounds.

the wheel is not for sale anymore do you have any other options

I love my US General toolbox

Use plati-dip spray coating or auto undercoating on the chrome drawer covers. Then they won't crack, chip, or scratch with usage.

420th like! 🌲

No need to say how it will perform based off how it looks based on opinion. Thats not a valid argument without proof. Good job overall

Saw a snap on box at the pawn shop today, I was comparing it mentally to my 6 drawer full bank cart until I looked at the price and realized a used one is 3x more expensive for the same quality. US general boxes give mechanics an achievable start and prevents many from ruining their retirement.