วีดีโอ

What software do i use to slice a file from STL to Gcode for this printer? Cura is not recognizing our printer and does not have it on their list. The. Lab slicer software on the micro SD card was blank, nothing in that file?

Why is my sensor light not turning off when I’m turning the screw?

This video is useless

How do you fix the firmware when the nozzle stops heating up? I checked that the nozzle isn’t the problem, but the temp goes down mid print and it’s because of either the firmware or the hardware

Why does it not print any thing else?

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

Worst compagnie ever !! Never respond to my email for technical support!! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !! NOT RECOMEND !!

the only good print i get i the rocket...any other is a fail !!!!

je comprend pas moi elle marche pas adhères pas au plateau par contre quand je fait une impression d'essaie livré avec l'imprimante 3D

this is helpful thank you so much.

sympa et pas chère par contre si c'est aussi casse-couille pour le réglage du plateau, c'est même pas la peine !...

Moi je fais de la pub de cette machine pour eux et j’ai trouvé 70 personnes qui l,on acheter

The nozzle raises up too high when I get to the point where I need to start leveling the bed. Any suggestions?

je ne trouve pas le logiciel labslicer, aurais tu un lien, ou les paramètres pour un autre slicer...cura par exemple ?

So what about those numbers being other than zero? You don’t adjust the offset like the picture in your directions?

comment faire faire imprime fonction j'ai installer cura mais comment ca foncontion

I bought one of these, 2 years ago. I got it to compare to my ender 3. Nice looking printer, ez set up. Leveled the bed, started a part (probably a benchy). The printer homes, goes to the start point, and buries the nozzle into the bed so hard it puts a dent in it! Trying many times. It's now setting on my "to do" pile, waiting for me to scrap it for parts.

I have this easythread x1 printer, can you help please, the nozzle doesn't go up or down, I have to move it myself

Where exactly do I connect the wires to the Ultrasonic Sensor. I have the instructions but they’re hard to read

Just got a new SX1 Mini printer. Leveling isn't working after tightening the screws, the model and printed aren't getting any closer. Watched you video on TH-cam, which didn't not show a proper angle but did show power should have a little resistance when loaded through. I have almost a 1/4" of space. Don't want to tighten the bed until the plastic supports break. Anyone kow can I correct this?

bonjour je ne sait pas pourquoi mais mon filament ne colle pas sur la plaque j ai pourtant bien mit l autocolant si vous pourrez me donner des information j en serait ravi

What app did you used to print

I wait 3 houers and its not worm and itz not printing

Labists sx1 beginners mini 3d printer can it make all 1:64 scale which is 28mm

I have to adjust every time? Whit mine ET4 in going Crazy. Or in have issue, or not have an idea, i repeat for the 100st time the procedure.. then i return It at amzn, and buy and elegoo ..i have nevercever have problema whit DIY prusas. ... Maybe was Better ..or mine ET4 can be have a firmware problem?

Hi labists, I need a video tutorial on how to do the labists 3D printing pen because I’m struggling how to set it up

Bonjour je veux bien la testé celle là

How to upgrade the firmware ?

Che filamento possiamo installare?

My printer is not auto leveling or manual leveling can not be achieved. When start the nozzle hit the plate and doesn’t stop. Is the sensor broken? When put my finger it does light red but not with the plate. ??

How long does it take for filament to extrude through?

Is the heatsink and fan necesarry? I bought the case en rasp. pi 4b and it's not included, neither are the screws.

Short answer: AVOID this hot trash. Cant print straight up in line with previous passes, little to no community making designs, slow, and constantly sounds like the fans are failing.

Stampa solo da microSD o anche via USB da PC?

N'acheter pas, c'est de la merde, j'ai beau avoir testé tout les paramètre du monde possible et inimaginable, IMPOSSIBLE de finir mes impressions 3D ! La machine s'arrête toute seul sans aucune raison ! ça fait 3 jours que je fais des test et j'ai réussis à imprimé que des pièces de 2 a 3 CM mais en ce qui concerne les grosse pièces de 12 CM maximum, impossible de les finir, la machine décide d'elle même de s'arrêter aléatoirement en pleins milieux de l'impression !

Need a board anyone know where I can get one

Wish there was information in this video instead of crappy midi music.

Which slicer would you use for this printer. (If it's Cura then which printer do you select as I can't see Labists in the list.)

How do I clean the nozzle?

if only it worked properly

Which type of filaments it supports?

You move so fast & don't tell exactly how to do it by stating what is what. All we can do is read & that really doesn't help Much. I'm stuck at the feeding Filament & its my coming through

Malheureusement Labists met plus d'effort a vendre qu'à donner du service. Je n'arrive pas a trouver des fournisseurs de pièces, une liste ou un schéma digne de ce nom pour les composantes de l'imprimante ou un manuel d'opération. Est-ce que quelqu'un peut m'indiquer une source d'information sur le web pour l'appareil SX1?.

Poor video.