วีดีโอ

hello, i had a couple ribs on my door panel broken so it wasn't on right in turn my locks were working right, there is a easy fix ( th-cam.com/video/AKqC0SdTL0U/w-d-xo.htmlfeature=shared

Hi Chris, thanks you, yep Gibbs programed

The slope of the 'C' pillar, back glass, and trunk kinda give it away. Definitely not a '67.

Aaron, Thank you, i hope things are going well

You may be able to change pulley size to get more rpms out of it

i could easy make inlays, but i don't what what to make or what i would want :)

yep i drained and replaced with new gear lube, and made sure the vent wasn't blocked, i still have the car with over 150,000 miles no problems

🤗

yea the nema 34 i bought another one works graeat

@@makosharkcnc7730 ok… have a nice day.

Thanks

Yeah I have to keep my hands off, it was a way to feel if the car came loose

Thanks for your advice, yep i know i need more RPM's! Trying to work on that!

thanks

@@makosharkcnc7730 Are you going to eventually make a whole car.

@@dogdollaz1971 yes next video i will be done with the whole car!

I'm buying one. Is that the only kind of wood you can use. Seems pretty soft especially with the rear spoiler,maybe thicker.

@@dogdollaz1971 Thanks! making 2 of them and wiling to sell one if you are interested will be done this week, i using select pinewood with no nots

Thanks Aaron, its coming out ok

weak?

thanks

Hi Aaron, Thanks for the thumps up and support my friend! been thinking about making something for you and mailing it to you, your machines are lot nicer!!

YEAH EMAIL ME

Hi

yea i would do it all over again/ i do have 30 years back ground on programing/ setup's on cnc mills, keep this in mind this is a small mill you need to take lighter cut's, it a good bang for the buck , i would consider going up one or 2 sizes in the mill that's a maybe and its extra money

@@makosharkcnc7730 Thank you for the quick response. Valuable advice.

@@CarlPugh are you buying one?

@@makosharkcnc7730 Yes. Either the 25MV or the 728VT. The latter is likely more that I need to cut mostly aluminum and will be harder to eventually convert.

Wow they cut the converters off, i thought there are hard to get too

@@makosharkcnc7730 Man I cut that thing right off And now I’m fighting with theinsurance company they keep closing out The claim I want to the shop to look at the Car and I started it up with no resonator Or Catalytic converter and those fumes are awful and the car sounds like a piece of junk So now I got to get them to put universal Catalytic converter on

@@cadillac9142that sucks/ I'm shopping around for new tires right now

@@makosharkcnc7730 awesome I had to do a timing chain repair also paid 2000 for the car and I’m into it 5500 and I had to buy a new ECM because the antitheft light would never go off and when it was on my AC will stop working it has a 2.8 V6

@@cadillac9142 mind has the 3.6 black, bought with 60k at 140k very little problems!

Rear differential. You better check the gear oil

Thank you

yea , i have 3 fixtures i use, 6 op's , Thanks you again!

Thank you very much i appreciate that!

i made one like your blue corvette th-cam.com/video/XShUJeNE-nE/w-d-xo.html

i have about a good 60 + run time hours! very little if any backlash so far, still tight

Thanks😃 what would you like to know

Hi, i have two more Operations left please subscribe and click the bell to be notified when my next videos come out i will be finishing it in the next two video's! i hope you can watch!

Thanks! I'm using GibbsCam

Hi Bill, I agree more RPM'S! i been trying to see if someone can make me that pulley design you sent me at a reasonable price no luck yet, i been cutting a little bit of alum. i have to go a bit slow and less depth of cut on my mill, when i'm cutting alum it seem to cut / rough lot better in Y AXIS

@@makosharkcnc7730Hmmm. You might double check the gibs then and see if one axis has more play than the other.

@@billstrahan4791 yea my X and Y are great, it's my Z axis has about .003 or so I'm not happy i contacted precision matthews they said it normal for the Z to have that much slop, and you need slop to raise and lower the head and they said what to do is bring the head down in place and then lock it that will take care of the problem, that's find for a manual mill not for a CNC i can adjust the gibs which i did but it seemed i had to move it too much and don't want to wear it out i put it back wear it was

Thanks Aaron!✌

😉😉

Thanks!

Thanks for the great tip!

Pecking haft the dia. Of the drill, rpm was around 1000 rpms its just a hobby mill, wd40 works well, or alcohol

Exactly right fly cutter, i just cleaned up the face and squared it

Made a ALUM. fixture use as a angle for the table on the mill i'll be using it on the up coming videos

😏Thanks!

That's on my list of cars to do. Next one i thinks is going to be gt500 Eleanor

Hi Rob, I just import the stl file to cam, i don't do any converting

@@makosharkcnc7730 ok , then the better question is , what cam software you using ?

@@airgunningyup Gibbscam

long time no see! hope things are well!

@@makosharkcnc7730 haha. Yes all is good. Just busy as always. I'm about to chsnge out my spindle bearings or atleast lube them. My spindle doesn't have a good feel to it. Thanks for asking.

Hi kent, i do have new bearing on hand, at the moment i don't need to replace them there smooth, quiet and tight yet

You might have a point. I bought the double it wasn't much more money maybe $15-20 more. My mill is nice and tight I'm very happy

@@makosharkcnc7730 agree. Somehow being inexpensive can change our outlook. Like Nevermind it's an overkill. 😊😊😊