- 2
- 12 719
Eiken Acres
United States
เข้าร่วมเมื่อ 15 มิ.ย. 2015
Our 20 acre farm we purchased in 2019, and it's also my own personal mental sanctuary to get away from city life and just work on random projects.
Dropped a camera down an old rock lined well on the property!
Exploring one of the old hand dug rock lined wells on the property.
Lighting the way with my homemade redneck diving floodlight made from a mason jar filled with cheap $1 led flashlights, attached to a bicycle water bottle holder, attached to the conduit/PVC pole my camera is mounted to.
Enjoy!
Lighting the way with my homemade redneck diving floodlight made from a mason jar filled with cheap $1 led flashlights, attached to a bicycle water bottle holder, attached to the conduit/PVC pole my camera is mounted to.
Enjoy!
มุมมอง: 210
วีดีโอ
How to remove seized cross bar on a rotary cutter (bush / brush hog)
มุมมอง 13K4 ปีที่แล้ว
Removing a cross bar that holds the rotary cutter blades off the vertical spindle or bottom gear shaft. This is a Woods M5 Dixie Cutter rotary cutter (Brush hog, Bush hog, Brush cutter, etc). This particular model had a cross bar that is pressed onto to the vertical shaft coming out of the bottom of the gear box, and you have to get creative to remove it. I noticed the replacement cross bars no...
Did you use oxy/acetylene? Rose bud or cutting head? Rose buds use alot of gas. Ive been just using my cutting tip
I have a woods 72-3 and need to change the main seal. Having the same problem. I'm heat and treated and beated but will try this..much thanks When I get mine off I'm putting antiseize on mine
I have removed the bar, can you show how to remove lower shaft to replace bearing ? Thanks if you can..
Dude! You saved me. Was trying to figure out how to get mine off without the "special tool" called for in the operator's manual on mine and this was the ticket.
How did you get the center bolt out?
Center volt takes 500 ft lbs of tourqe. I chained the bar to upper part to hold right then big 6 foot breaker bar , very sweet came off.
Anti-sieze is your friend. If you would check oil level in gearbox prior to use,you would have seen your seal was bad.
Great video!! Going to use this same idea to remove mine. I have a Woods BB72X.
Thanks. Been looking everywhere to find how this style comes apart. Think I may just go with the pack the box with grease method after seeing this. Lol.
Excelent... got mine off in 5 mins thanks to you!
I have the same problem with a older New Holland cutter. Thanks for the idea, I'll give this a try!
This worked great!!! Thanks for posting this. Took like 15 minutes and no torch.
I should add that I have an MD160. Same type of cross bar and design. Also, I almost gave up on this method. I had the jack cranked as far as I could get it before I heard the first crack and sign that it was letting loose. I was using a 12 ton jack as well and a short chunk of rail road track but no heat as I was trying to preserve my shaft seal. I suspected the seal was bad but wanted to inspect it first. This saved me a bunch of money. Local repair shop estimated 6 hours to remove the cross bar, inspect/replace the seal, and replace the blades. I did all of that in less than three with this method and that included wire wheeling all the parts before reassembly and using plenty of anti-seize. If I had to do it over again, I would use a 20 ton jack and an even bigger chain just to be sure. Thanks again for the tip!
Glad I could save you some time and money. I've been saved a lot of headaches and money by learning from others on here, so I figured I would give back a little, and someone could glean something from all my troubles... Lol
This works great. I did something similar last year after trying everything else.
No stump jumper??
No, I bought an old 1945 Farmall H that came with this brush hog. Funny thing is I bought another identical used M5 for parts, and they were twins, no stump jumper on it either. I probably should add one as much crap as I end up running over. We bought an old 20 acre farm that has all kinds of surprises I keep finding the hard way when I mow... Lol
The bottle jack & chain to me is the easiest I looked and searched all over the internet on how to remove my stump jumper from my 21 year old bush hog. I even called the manufacturer in Ozark , Alabama and they just said apply heat and wood wedges which didnt work Finally a good friend that has his own welding shop told me about the bottle jack and chain. It popped off relatively easy but I sure thought the chain would break first. Your video is the first one I have encountered. Thanks for sharing it. It will help many folks from now on!!!
Having to tackle this same thing, like the idea and will put it to use! Thanks for taking the time to video your work.
I had the same i used your idea it works great thanks i based it and wood not come off but the jack got it of
Having to remove our bar to rebuild box now, best idea I've seen. Going to try this, I knew it would be a pain. Thanks