วีดีโอ

I dod that still didn't work

What if the T don't line up with the notch?

I'm doing it right now. If it starts. I'm subscribing to ur channel.

Man I needed this, respect ...replaced piston a rings and new intake valve my so s bike we got him and it's been a while so needed a refresher to double check afew things, great video

Do you know that the part is above the oil pump in side the motor

I know it’s probably a long shot but I am rewiring my 85 virago xv1000 and need a full starting diagram with diode size and if possible the rest to do head light and tail light and signals the signals will be led

This is the best video that I have found on the internet explaining the timing on these. Thank you so very much for making this.

Replaced my head gaske on my Tao tao 125cc got all the time mark lined up close everything up started motor and got a loud tapping sound so I guess I failed... I've done timming chains before on cars never had problems???

Confident I can set timing right after I replace all those gaskets thanks to your video.

This is specific comment on xv1100 models!!! All around good info but the information only applies to xv1100 models 95 and under. I have found that that the term "pick-up coils" cannot be taken literally. The 96 and 97 models ( really I am working on xv1100 ) have only two wires running from the case and I am unsure as to where the other two truly come from! This has created so much of a crazy mess of this for me! I have attempted using coils from 750 now which has four wires and so on and so forth!!! If you could help me with the 97 xv1100 ignition circuit I'd appreciate it!!

Did you remove the car entire factory wiring harness

Thanks Joe, your video helped many of our time!

Thank you sir I just ordered mine on Amazon I'm going to try to change it tomorrow

noice

Thank you good sir!!

I need sum help with my Yamaha 1100 please I like the way you explain things I'm stuck on tci box do to no spark but turning over so I removed the box cut the plug and don't know where the wire go exactly

Please stop chewing???!!!

I'm at the point where I have to put the sproket on cylinder assembly, but I don't have the slack on the chain to line up sproket...it's there but not there...this is a raptor 90..any advice would be greatly appreciated Thanks

is there a difference between the exhaust stroke and intake stroke?

Hey, I know it's probably a few years too late, but I would really like to pick your brain how you wired in the push button start. I'm trying to do it on my xv1100, and you said it's a 2-circuit switch and I want to know how to wire in the button up with that. Is there any way I can get ahold of you?

You make it seem so easy thank you brother

Best most informative no bs Chinese motor video I’ve seen yet. Thank you

Hey hey video fucking grate ! A got a virago 1100 98 rebilt complet wirring a need helps do you know how to speak french my friend? I almost got it fuck! 😂 thx for your help !

Nigga did you have to be eating while making a video

So freaking grateful for this video! Really appreciate it.

So you still using this set up, did it work?

I noticed the gasket you're using between the cylinder and the valve head is that rigid composite gasket, rather than the flexible cardboard gasket. I was wondering if you've ever had any problems/issues with that setup? I have an extra rigid gasket and to me it seems like a better choice over the cardboard, but I'm not an expert or anything. Perhaps it doesn't seal quite as well? Edit: It's possible that on my engine, someone mistakenly used the cardboard gasket for the valve head (combustion chamber area). I just noticed on another video that the darker rigid gasket was used, just like in your video.

had a good feeling at the start of this video and i was right you helped me out so much i took my engine apart a years ago just forgot about it wanted to put it together did that turned it by hand glad i did turn it by hand cuz my valves was touching the piston thats when i found your video

thank you brotha made it so easy keep up the good work

I need video with cdi, thanks

Where do the little springs go?

Should’ve watched this video first… so I removed that 10mm bolt holding that black round thing. Do I have to pull the engine or is there another way pls help

Nexted time quit smacking it's annoying

Not sure if this will reach you, but I’m trying to figure out how to adjust where the piston head is in relation to the mark on my fly wheel. When I line up the mark on my flywheel to the one in my case, the piston head is all the way at the bottom of the cylinder. The original flywheel that came with the bike I bought was completely rusted because there was a crack in the cover which caused water to sit inside and rust it to pieces. Is there a way for me to adjust where the piston head is without adjusting the position of the flywheel?

don't eat food mile making a video no one to hear you gums snapping its disgusting

Did not work on my Dodge Stratus

@kevinjanes1320 • 5s ago 11:01 my TCI is different. 4 prong plug on left top left=grey Bottom left=orange Top right=red/white stripe Bottom right=black 8 prong plug on right Starting on top row left to right 1.white 2.green 3.blue 4.grey 5.black/blue stripe 6.blue/black stripe 7.blue/red stripe 8.yellow

What is the torque specs for the crankcase

No gloves that's very unprofessionaljoe but I like it I do the same 😂 I'm noglovettbackyardmechanic

Thank goodness you made this vid. Saved me buckets of time. Thankyou.

What's the difference between the cdi and tci

I got these led lights I'm putting on my 98 xv1100 I need to tap into the left and right side turn signal wires and break because when you turn the signal on and or break the one side depending which turn signal you hit makes that whole sides lights flash same with when you hit the break they all turn red but can't find a wire diagram to find the separate turn signal wires and break wire do you have any way to help me find that out please?

Bro god bless you I’ve been struggling with that shit for like a month and it finally worked

Really appreciated video - great and carefully performed!

Most helpful , thank you !

is this chopper wiring ?

great vid. thanks

Hey Can you tell me what the valve clearance is supposed to be on these 110Strip the spark plug on my son's but I got him another cylinder I just wanted to check the valves before I put it in

Very useful, thank you!

Great video