- 70
- 172 064
Cobey Schmidt
เข้าร่วมเมื่อ 26 ส.ค. 2013
Adjusting the framing for xTool F1 Ultra with Lightburn
Still doing inspections and testing under Lightburn with the xTool F1 Ultra I purchased on launch day, but made this clip to address an issue expressed by other Lightburn users
มุมมอง: 335
วีดีโอ
Les Toil laser engraved
มุมมอง 1314 หลายเดือนก่อน
My friend Les Toil, a real traditional artist, allowed me to render out some of his artwork on the laser. He does do commissioned work, so if you're interested in supporting an artist, check him out at lestoil.net
2.5D engravings on the Creality Falcon2 22W
มุมมอง 2716 หลายเดือนก่อน
Finishing up a week of 2.5D engravings on the Creality Falcon2 22W. #laserengraving #laserart #art #laser #laseretched
Creality Falcon2 camera kit final test run
มุมมอง 7696 หลายเดือนก่อน
After playing with the Falcon2 for a few weeks, I adapted my standard camera kit to it. Calibration went off without a hitch and now it's time for photos before posting to the Geeks At Large website and Etsy shops geeks-at-large.com/product/creality-falcon2-camera-kit/ geeksatlarge.etsy.com/listing/1681664275/creality-falcon2-engraver-camera-kit
Tensioning the belts on your laser engraver using the Prusa belt tension tool
มุมมอง 1.7K11 หลายเดือนก่อน
Tensioning the belts on your laser engraver using the Prusa belt tension tool
PSA: Elegoo Phecda Air Filter Performance
มุมมอง 1.7Kปีที่แล้ว
PSA: Elegoo Phecda Air Filter Performance
Elegoo Phecda 10W - Part 1 (Post Assembly)
มุมมอง 4.9Kปีที่แล้ว
Elegoo Phecda 10W - Part 1 (Post Assembly)
Quick and Dirty Explanation of Grayscale vs Jarvis (or any other dither algorithm)
มุมมอง 3.5Kปีที่แล้ว
Quick and Dirty Explanation of Grayscale vs Jarvis (or any other dither algorithm)
Quick Explanation of Centering Graphics On a Tumbler
มุมมอง 393ปีที่แล้ว
Quick Explanation of Centering Graphics On a Tumbler
Answering the 'Why does my xTool not go left & right'
มุมมอง 1.7Kปีที่แล้ว
Answering the 'Why does my xTool not go left & right'
Mirror Engraving - When to invert and when to not
มุมมอง 758ปีที่แล้ว
Mirror Engraving - When to invert and when to not
Introduction to Hybrid 2 from Geeks At Large
มุมมอง 2.7Kปีที่แล้ว
Introduction to Hybrid 2 from Geeks At Large
GeeksAtLarge Air Assist Install For the D1 20W and D1 Pro
มุมมอง 2.5K2 ปีที่แล้ว
GeeksAtLarge Air Assist Install For the D1 20W and D1 Pro
Manually Program xTool D1 Firmware (NOT PRO)
มุมมอง 3.9K2 ปีที่แล้ว
Manually Program xTool D1 Firmware (NOT PRO)
Setting Up WiFi on the Devil1 Lobotomy Kit for xTool D1
มุมมอง 8512 ปีที่แล้ว
Setting Up WiFi on the Devil1 Lobotomy Kit for xTool D1
Devil1 Lobotomy Kit Lightburn Installation
มุมมอง 1.6K2 ปีที่แล้ว
Devil1 Lobotomy Kit Lightburn Installation
Hardware Installation of Devil1 Lobotomy Kit for xTool D1
มุมมอง 2.5K2 ปีที่แล้ว
Hardware Installation of Devil1 Lobotomy Kit for xTool D1
GeeksAtLarge Devil1 Lobotomy kit for the xTool D1 intro
มุมมอง 6K2 ปีที่แล้ว
GeeksAtLarge Devil1 Lobotomy kit for the xTool D1 intro
Assembly and Hardware Installation for the GaL Camera Kit for Atomstack Laser Engravers
มุมมอง 1K2 ปีที่แล้ว
Assembly and Hardware Installation for the GaL Camera Kit for Atomstack Laser Engravers
Installation of the GeeksAtLarge All Metal Lever
มุมมอง 9832 ปีที่แล้ว
Installation of the GeeksAtLarge All Metal Lever
GeeksAtLarge v9 Air Assist Kit Installation
มุมมอง 2.1K2 ปีที่แล้ว
GeeksAtLarge v9 Air Assist Kit Installation