- 10
- 4 676
OPAAT GARAGE
เข้าร่วมเมื่อ 29 ธ.ค. 2023
Silverado Truck Build pt 3 Belltech 3/5 suspension drop
welcome back. in this video follow along as we remove all of the old stock chevy suspension and install the Belltech 3 inch front drop springs and DJM upper control arms. links below. I will show the rear drop when we install the built rear-end. thanks for watching.
#opaatgarage #belltechsuspension #djmsuspension #silverado #chucky #automotive #suspension #loweringsprings
#opaatgarage #belltechsuspension #djmsuspension #silverado #chucky #automotive #suspension #loweringsprings
มุมมอง: 60
วีดีโอ
Ram 1500 Oil Pressure Sensor diagnostic and Repair
มุมมอง 2.1K9 หลายเดือนก่อน
in this video we will be diagnosing the issues with 5.7L hemi reading high oil pressure and replacing the OIL PRESSURE SENSOR. #opaatgarage #automotive #ram1500 #hemi Part# PS401 - OIL pressure sensor/switch www.autozone.com/external-engine/oil-pressure-switch/p/duralast-oil-pressure-switch-ps401/704844_0_0
Silverado Truck Build pt. 2
มุมมอง 999 หลายเดือนก่อน
welcome back! in this video ride along as we get the cab and frame cleaned, preped and painted. I want to give a huge thanks to the subscribers who has clicked those much needed buttons to help grow the channel. please make sure to watch the video in full length and share it to all your friends. #opaatgarage #truckbuild #silverado #rustoleum #automotive #diy #bodywork
HOW TO and REVIEW of the VEVOR GD90e spot dent puller
มุมมอง 1.9K10 หลายเดือนก่อน
welcome back to OPAAT GARAGE. in this video you will see a quick how to and review of the VEVOR spot dent puller. For all the DIY guys this is an easy to use and must have for the shop. see link below for the dent puller. remember hit the like and subscribe buttons, and leave me a comment. #opaatgarage #diy #vevordentpuller #bodywork #automotive www.vevor.com/stud-welder-c_10074/panel-spot-pull...
Waste Oil Burner PT. 2
มุมมอง 22810 หลายเดือนก่อน
it's cheechin, but nit like I hoped. I quickly learned what fixes and upgrades needed to be done. thanks for watching. don't forget to LIKE, COMMENT, and SUBSCRIBE. #opaatgarage #diy #wasteoilburner
Waste Oil Burner PT. 1
มุมมอง 5110 หลายเดือนก่อน
welcome back! in this video, you will see the plumbing of the waste oil burner. PT 2 will be out soon, finishing up the drip line and firing it up. Dual BBQ blower Charcoal Chimney Starter BBQ Fan, Smoker Fan,Electric Blower Starter for Charcoal,AC & DC Power cord Included a.co/d/7LPA0RD #opaatgarage #wasteoilburner #barrelstove #diy
Silverado Truck build introduction
มุมมอง 6310 หลายเดือนก่อน
Hello! thanks for watching. in this video I share my journey on building my street truck that I call Chucky! follow along as I give alittle introduction and get started on tear down and body work. #opaatgarage
New facia and soffit
มุมมอง 2210 หลายเดือนก่อน
in this video, my best bud, Cody and my brother in law Matt helps with tearing out old facia and soffit and installing new stuff to help with cutting out the north wind. thanks for watching. Please like, comment, and smash the subscribe button!
installing wood burning stove
มุมมอง 4411 หลายเดือนก่อน
in this video we are working in installing the wood burning stove and finishing up the back wall with some insulation and sheet metal. thanks for watching! please don't forget to like, comment and smash the subscribe button!
channel start up.
มุมมอง 58ปีที่แล้ว
first project on the channel is getting the shop ready for the power company to set the electric meter. I want to give a BIG thanks to @twinsticks garage and @WelkerFarms for the inspiration to start my own channel. please like, subscribe and comment. stay tuned for more projects.
Had the same issue when I first got this puller. I was just sanding the repair area to bare metal using my da sander and 80 grit, puller kept coming off with small amounts of pressure when pulling. I switched over to an angle grinder with a 40 grit disk and it works how it’s supposed to now. Give it a shot.
I bought one of those too, but found I had to push the power up to max (9) and even then, it pops off too easy. NO WHERE near even starting to burn a hole! I wish! but OK for light flemsy panels, or for small dimples like you showed. I was hoping it would grab hard and pull some serious dents out. Didn't work for me. Did you end up having to run clear up on max power? Or did you run it on 220 instead of 110? I haven't tried that yet, but will do that next.
Great job
Thank you
The time lapse shows nothing bud lets see how it works in real time!
I will be doing another video doing some body work on the bed of chucky. I'll be sure to slow it down for you then. Thanks for the comments.
Looking 🔥
Thank you
Unfortunately that isn't available in the UK. The British government have basically stopped Vevor selling electrical products into the UK because of safety concerns. More than 90 products were at risk of electric shock, fire, burns and injuries.
Mine definitely shocked me it worked so well. But I will keep this comment close by just to be on the safe side. Thanks!
@@OPAATGARAGE Most of the issues involved loose wires, might be worth checking all of the connectors are cinched up correctly.
@spencereagle1118 I will definitely check that tonight. Tha k you for the comments.
Completion and big burn outs
YOUR DOING GREST DAD
Levi in the middle made me laugh so much
Me to! He's a nut!
😮
🫡🫡🫡
Thank you sir.
Why the coils 🤷🏾♂️ it will always flow over because it's to small of the oil tubing i had the same problem
Thanks for the comment, there was no reason behind the coils. I was just going for a cool look. I am upgrading the line to a 5/8 inch line and fewer coils.
@OPAATGARAGE yea that's better to upgrade I did upgrade mine now works flawless good job tho
@cebasmb8250 thanks triple CCC.
Fuckin dope 🤙🏼
I like the new outro, keep it up dad
Thanks, I'm still learning and playing around with the whole edit thing.
Nice
Cheechin!
Excited to see the progress. Keep it up man!
Appreciate it!
Can I have credit for helping with that there green house
I'll give credit where credit is due my guy! Hopefully the weather and budget will get more work done on that thing soon.
Congratulations! Can't wait to see your progress!
Thank you!!