วีดีโอ

Amazing video! Very cool. So all in all, how much did this cost you?

Cześć, fajny film. Też buduje Vorona 2.4 R2 na moim polskim kanale. Jeśli masz ochotę zerknij.

This video looks like it should be from a subscriber with atleast 100k subs. Very nice, clean and to the point work with some good editing.

How does it compare to the SOVOL SV08?

Ultra hardcore DIY with metal works and a bit of engineering. Props.

Tools from 1,5mm to 3mm in 5 mm increments? How does that work

I eat those side panels as crackers

the 2.4 DOES uses a Z endstop, they just call it Z probe. the inductive probe (like klicky with a basic confic) is just used to level the Gantry and to create a bed mesh. you still always home Z on the z-Probe and set your nozzle offset on a reference point on the bed. you can get around it, but i would consider this advanced.

Very well done mate💯 ! - i can just agree its the best printer to get ... but also a dangerous rabbit hole 😅 Klicky and sexbolt is absolutely the best combination for z offset calibration... i recommend a nozzle brush too... due to inconsistencies i already ripped my PEI sheet 💀 Next step is to give it some speed... and at least go stealth burner ... maybe with Canbus ? for people that get themselves a new kit... i can recommend MagicPhoenix out of my own experience, lots of customisation...and it comes with Stealthburner and Canbus

This video is amazing!

i like voron tap way more than clicky

Read about canbus and Tap click - you will save time with cables. You get a thumbs up from me for encouragement!

Step 1: Buy Sovol SV08

what's with the stack of cash on 1:11?, hahhahhaahah

Cool Video. Can't help but notice thought that the Formbot Kit I am looking at purchasing is already quite changed to the one you built. It is advertised on the Website with Manta M8P and Can Daughter boards EBB SB2209 CAN /EBB SB00000 CAN and a VORON TAP Variation. So might be great if you still have it to post the BOM your kit came as a comment perhaps so that your tips and tricks are easier to apply to newer kits.

your bike is a bit small for you. or you need to put your seat higher.

Ive used THE cheapest tubes like 2 euros a piece and that shit was fine😂😂 maybe you need a bit smaller size

Disc brakes are heavier than rim brakes and may be over rated. You definitely need good brakes for an e-bike. I have been doing some research and quality rim brakes may be a better solution for a lot of ebike conversions based on frames without disc brake mounts and your conversion proves there may be other problems with conversions as well! Off road pedal dirt bikers and road bikers, prefer quality rim brakes, besides being lighter, they really work well! Rim brakes vary in quality a lot. Good ones cost $$$.

Hmm, interesting. I was wondering if it was even possible to do a conversion on a dual suspension. I've got a 2004ish Mongoose Teocali comp I wanna do a conversion on but the frame and suspension setup is a bit different to this bike so I need to a bit more research and go see the guys at the local bike shops to see what they think the best setup would be. 👍🙂

You need room for larger bitcoin . $100000 won’t work

Hey mate, is the amp size of the battery?

Did you get the 52v or 48v,cheers

hey there, i was looking to convert a bike and i was wondering instead of putting everything inside the frame have you ever wondered to put the controller or battery on top of the frame in between the handlebar and the seat?

Does anyone have an up to date step by step guide with the Max 7219 LED Matrix ?

What do you do of your donor bike has hydraulic brakes? Then u can install the supplied e-brake in those kits that cuts the motor when braking right?

How do I do this with aquarium fish?

My bikes got 2.35 tyres with puncture proof inserts and slime tubes , had 1 flat in thousands of miles

when youre riding at the end of the video, youre using nearly all the suspension travel meaning you havent adjusted the rear shock for all the additionl weight. consider increasing the air pressure in the rear shock

keep grinding dude.

Why didn't you show the before and after pic of the cassette hub which you narrowed down by taking out a cog from 7 to 6 ? Actually why didn't you just get a quality 6 cog cassette which presumeably is narrower? would be easier than the bearing install no?

What is it a 48v 13 ah battery?

I used to same bike but is xcaliber 8. I believe is the same frame. I used the same 29inch wheel 2000w MTX RIM. But I didn't have any the problems you did. The 12 speed cassette fitted perfect. The brake caliper fitted perfect. It was like plug and play Actually it was the most easiest DIY Ebike I have done.

The whole problem is from the bike frame, it was necessary not to save money and take a good donor for a homemade bike.

Can I fit in a 28 inch motor wheel on a 27.5 bike

Where did you get the battery mounting bracket from? I don't see any batter coming with that.

😔 "Promosm"

in my experience putting the controller in a case cooks the thing.

Nice bike! Which hailong battery case is that? What dimensions? Thx

Great build bro, do you have a link for the torque arm?

sick build

Nice build. Not an "exact" replica but it's close. I've done a few builds of it - on my thingiverse I also have an exact 1:1 model for "The Boring Company" badge modeled from measurements off a original one.

hi

Hi Aaron thanks for the video. where did you buy the motor for the bike.Thanks

Nice build i just finished mine but i have an issue is it normal that the casette moves in that way as you showed 3:10, mine doesent click but moves in that way, after changing bearing did he moves?

The same with EV car tires. They will wear out faster and frequent tire rotations are necessary to even out the wear on all four tires.

Hey Aaron! Love the build, I am hoping to build something similar. I could be mistaken, but I didn't notice a mention of frame size during your video. If you have a moment to check, I would love to know the size, as I'm wondering if sizing up would be prudent in the interest of maximizing triangle space. Cheers, and thanks for the inspiration!

How much harder is it to pedal an custom ebike on your own, like this one, than your bicycle before the conversion?

Nice build, I have just converted my bike to electric using a kirbebike kit also but using a front hub motor 350 watt with an mtx39 rim paired with a 48v 20ah 960 wh battery LG cells.

4:50 don't you mean 20% charge increments? 5 segments total there (20 * 5 = 100)

your washers are not installed properly the the torque washer should be on the outside not the inside of the drop out assembly