วีดีโอ

thanks lot bro

Why is this video three hours long? I'm running out of batteries

Where is the oil Drain ?

great video

Great video, thank you so much for posting. I followed your video and my saw no longer leaks oil. Thank you again.

Thank you Thank you!!!

Thank you very much Señor!!! You are a life saver. Now I know what to do with the leak, on this machine!!!!

Excellent video, thank You so much! God Bless Y'all ❤️

You should me way more than anybody else about changing that crankcase oil line so thank you ! I really do appreciate it great video

I can't focus on what you're saying . try taking your shirt off , that might help , thanks 😊

The passer by wasn't a paid actor, but I bet the chicken was

what kind of stand is that and what do you have it hooked to? Are you behind a dumb trailer or is that hooked to a truck?

45’d the angle or rounded out that mount to the bed just to minimize the stress points when the bed flexes but I’m no engineer great video 👍🏽😎

Great job!

Thank you for this I had the exact same issue, and your video worked perfectly for my saw. Not only did it fix the leak but it ran so much better, this could partially be to my primer build being trashed.

Bon Boulo 😆😆👍👍

I thought hey alright someone building something that actually has half a brain, until measure 17" on the floor and eyeball the center line on the cross member on the floor. Just measure 17" from the center line on the cross member each way and line the rail up with the 2 17" marks.

Everyone worries about those damn rivets. There isn't a thing wrong with the rails sitting on top of the rivets.

MUY BONITO TRABAJO

Where do you dump in your area do you know how much a full load way

Nice work for the limited tools you have. I made my own beds as well, but all of them dump. I could not live without a dumping bed.

Excellent video: exactly step by step, no unnecessary talking, no music that does nothing for me except make it very hard to hear instructions, and the part identified at the beginning of the video where I can go back and find it. All this made me subscribe. Exactly how a how-to video should be made. My free (!) 455 has this exact problem, now I can fix easily, thanks!!!

all the critical steps are there. Thanks

if I had done that to my chainsaw it would be in the trash by now. I would have many leftover parts on my table

I see your wearing your Sally pants @ 5:30 while using a cutting torch! Typical Yuppie outfit.

quick question, I know you welded on the little blocks to clear the rivet, is there a reason why you didn't just drill a hole in the flange of the channel to clear that rivet? allowing the full length of the channel flange to sit on the truck rail?

Exactly my issue thank you very much for the great camera angles step by step instructions my 455 rancher runs like a dream now

Thank you. Mine is a 435, and it started leaking every time I fill the tank.Doent seem to leak while running,but the tank will empty when it's being stored. I'll work on it tomorrow and let you know if I can get it fixed. Thanks again. Very concise video.

I would replace all fule lines and return bulb at the same time , just replace one is like a ticking time bomb 💡 Do the job right the first time something Americans lack 🤔 Ww2 looks like a waste of time too

I spend a lot of time fixing small engines and motorcycles. I use a lot of TH-cam videos for things. I’m not familiar with. This is 100% the best video I’ve seen in many years. From beginning to end you show exactly what needs to be done. it was exactly the fix I needed and would have taken me hours to figure out, thank you and good luck with your future

Wonderful camera work and exceptional narrating of each step. Everything stayed in focus and the disassembly / reassembly was done without the hands getting in the way. Great job!

The aluminum plate should have been replaced, looks like it is worn badly at the bottom as well as the short tube that transfers the oil from the pump to the bar. Hardly no cost and could be worn. I would replace the needle bearing cage and the worm gear as well. The saw looks like it has been used quite a bit and these things will sooner or later wear out, may as well do it while you have it torn down. Great video, really showed the steps with great up close shots.

I watched a lot of instructional videos to fix things. This has to be one of the best explained to a lay person I have seen. Every aspect covered from taking apart, fixing, and reassembly. Most videos just say reverse the process putting it back together. I give you an A++ on this. By the way this is exactly the problem I am currently having with mine. Probably my fault for not always using N/A gas. Thanks!!

Excellent video - straightforward n' clear. The only deviation I did was to completely remove the fuel cap and gently shake my rancher with the fuel tank opening pointing down and the remainder of the broken hose fell out. Handy if you dont have some offset needle-nose pliers or your needle nose pliers just weren't long enough to grab the broken piece of hose. Good stuff man - keep em' comin'.

great video. Thank you. Mine has been leaking almost from the day I bought it and its been a real pain with oil leaking all over the bed of truck, garage floor, etc.

Thank you for your effort. A great help.

Best video explanation on how to fix this problem. Well done!! And thank you!

Also, when i bought my 450 rancher new, I'd assume that the saw sat on the shelf at the store for so long, it dry rotted, only used it 3 times, oil leaked everywhere

Gonna take mine to a shop, good video tho

Absolutely fantastic video

Wow - this was amazing. Link to full line and all. Thank you so much.

This is very helpful. I'm curious if a B2601 with a loader and backhoe will fit in my shed. With the hoe to the side, the length will fit. Do you know the width dimension with the hoe to the side?

This was an awesome tutorial!

Great video. Right on the money. You saved me about $150.00. Thank you.

Don’t understand why you would use a grapple to fill in a hole & not the bucket ? 🤷‍♂️

both calipers come together when you ordered them?

It would be hard to improve on what you did in this video. The alternative is to spend probably 50 to 100 dollars at a repair shop to replace a 2 dollar fuel hose. It is a time consuming job that requires some patience and hand skill with the small parts, so not a job for everybody. Big thank you for the fine tutorial.

What size trailer?

Easy to understand.clear instructions..very good

Matt you’re the man