วีดีโอ

HOLA, BUEN DIA, DONDE COMPARTES EL JALON?

Can this procedure be used on a 2021 Audi Q3? I’ve been hearing for the 21 and up you need to turn service mode on

Who’s tuning???? My 6.7 doesn’t hit limiter like this.

Who’s tuning???? Tell me.

Can u say what electrically u are doing? I have a Tacoma with after market lights like yours the shocks where one build doing high and low. I'm trying to do this but I can't seem to find a like scenario ...

What intake are you using?

What intake were you using?

How did you make up your own map ?? My brother has a 2002 Volkswagen mk4 Jetta tdi 1.9t

Thanks my one not with immo, sobvery good

Hi i just like to ask you about dsg gearbox. How did you programing the gearbox to work other car? Someone say if i fitt a dsg 1 car to other, even the engine code same the dsg wont work. Thanks

u a genious my guy

Build engine?

Hi i have missing message from steering control modul fault and Cruise control not working. I saw IE coding dsg what do you coding with that? Thanks

Alr lets see banger¿

Is your Tiguan push to start?

Where did you buy the kit from?

Who’s tuning

Cold idle 20 psi at least. You got 40 psi Specs: Cold 2000-2500 rpm should be 50 psi Warm to 190F: Specs : 2.7 to 4 bar at 2k rpm (39psi to 58 psi) You got at idle 19 psi, at 2k u have 40 psi so u are at the lower end but within specs

Thank you man 🙌

Where do you get the dash kit the pioneer radio from

Almost twice the acceleration. How’s the mpg doing ?

Do you happen to have the colors per coil packs? I think I repinned them wrong

So what would be the reason the belt won’t go over the last part? Trying to do this at home and the belt is not wanting to stretch over last part. Thanks

Hi. Did you have any issues with the ABS?

Have to this video. I broke two clips on the connectors for cylinder 2 and 3 today changing spark plugs on my 21 atlas. I put them back and they seem secure but im still worried.

They got videos with these geniuses taking the rim, wheel housing plastics talk about overkill?

Pliable is the word you’re looking for

How did you get that light switch? My 2014 Jetta only has on and off and I was wondering if were possible to mod it so that I could get a switch like yours that has an auto feature which will turn on the low and high beams at a certain time of day.

might be good to clean the engine first, remove leaves and dry it up?

I’m trying to push the pins back in the new connector but I’m not hearing a click and I can just pull them out of it

If the gb is tuned, after this process, the tune remains or gets reset?? Or it depends on the tune??

what was stock transmission dq200??

Nasty car… clean it first… how would a healthy person sit in that trash

Had to stop the video due to motion sickness.

in my case the problem (oil pressure warning on idle) was dirty vvt adjuster/magnet! Litle bit of parts cleaner sprayed in each hole and problem is solved!!!

Where did you buy the kit?

Thanks for checking out the digital caliper!

Good vid although your airbag light was still illuminated at the end?

¨wich voltage should the signal wire give ? mine is getting 12 volts, but not working, and the signal wire is when its hot giving 3,4 v

Thanks for doing this I’m going to be doing this on my 04 Odyssey soon

Greetings, As always another great detailed video production 🇺🇲🍾🎉🇺🇲 Would you provide me with the link to purchase the skid plate. Thank you so much for assisting me and keep producing more videos about the KLR

As the pressure sensor is just a switch, it needs the ground terminal via the M10 thread, so covering it in PTFE tape won't help in doing that. The crush washer is what gives the seal, the new sensor should come with one. I had a similar problem with a bad sensor today.

Pdiddy pc

How to make a 20sec video 6 minutes long.....

Do you think the motor would die without wmi and no arp hardware ir basically a stock motor

Good vid I will try in my Jetta

Turn the ignition on amd repleace the parking brake as normal and then wind back with wind back tool. Once new discs and pads are all fitted just put the parking brake back on. Will work fine l.

I also have the same problem i.e. damaged plastic connector housings. This vid showed me how to tackle the replacement job. Many thanks.

Looks stock mine moves up in 3 increments

Hello, this comment is not related to this video, but i've watched your dsg conversion and i wanted to ask a thing or two. Do i need to code something when i'm done with the wiring and will vcds do the job? Thanks in advance!