วีดีโอ

I have this model GDF520PGJ5WW and it has power and runs when we start it but randomly beeps 3 in a row but not on a timer one day we will hear it do the 3 in the row beep just once and the next day 5 and the following day 7. Has anyone experienced this?

Saved $$$! Hair clogged the circ pump. Didn't need replacement part, just a cleanout. Thx!

Nice video. All is complete except bolting the gear case back to the three mounting brackets. I cannot get the holes aligned with the recessed mounts. It won't fully go on. What is next? (Clutch spring is at the top, white thing that protrudes on the other side is at the bottom.) I measured the holes in the gear case. The bottom one is the tightest fit: hole at 0.494" and recessed mount at 0.488". Not much wiggle room at 0.006"! Would it be beneficial to file the mount a bit so it will fit into the hole better?

Thank you!

I thank you!

Good job, as a beginner you kept a good pace there I could rewind a little and still follow. Thanks Word

they make a tool for that. works really well

Great videos. I was particularly interested to see how you re-attached the water pump clips and saw that you, just like everyone else in their videos, it's a quick press-and-snap, which is exactly how I did mine. What I also noticed was that you, as the others, never show how to pop in the other two clips, which should easily pop into place as does the front one. And I know why no one takes the time to demonstrate just how easy it is to re-install those clips. It's because the one located on the right side can be a little bit of a bitch with it located right at the hose hookup. The clip on the rear isn't a "little bitch", it's the full-grown, ain't-no-doubt-about-it, cuss out grandma, evil mother-in-law pain in the ass bitch to reinstall. Not only is there limited space and a difficult angle to work in, but the brainless designer of the model I have placed the metal framework just below the area where the bottom of the clip is supposed to attach. Now maybe it's just me, but if you agree that clip will make you want to just buy a new washer and have any tips, please pass them along. Thanks,

So if the light is blinking that means it’s good right? And I should buy a display panel

after so long ago , how well did the repair hold????

In 2021 we received our 4 appliances paid 9k for all. Microwave oven , fridge, stove and the dishwasher all needed repairs. Now dishwasher needs a part I fond on Amazon ca for 280$ . I'm going to junk the GE and never again buy GE. Fucken garbage.

Excellent job and great video! You get right of the meat of Troubleshooting the problem without any extra blah blah blah yada yada yada. Direct, short concise and informative excellent!

By the way there are (4) four blue springs in the front, #37575, two on left and two on the right and (2) two green springs in the back, #201521. Front are easy to remove, the springs in back, heavy duty, are not as easily removed and replaced.

I don't think the emptying of the shop vac is that important it wastes tome

So how do you get the back springs out?

9o

My broke down months ago.I left it alone cause idk what I’m doing ,but I unplugged 2 cables underneath it banged one on the floor idk if that did it but it works now. Lol, Ty

I have an issue. I just replaced mine (on my own) but ive had it replaced before but an appliance tech and this is the 2nd time my tc5 destroys the drain pump. Any ideas?

Speed queen owner here, model AWN63RSN116TW01, I had it stop many times blinking on rinse and wash, so I replaced the drain hose and also the cold and hot water hoses. I still get the error, what could it be now? The drain pump? I saw no leaking underneath when I replaced the hose, everything looks good under there and fairly new.

Dude it’s like a horror film!

Thats great can you show me how to do this

Sweet!! That's a great method! Thank you!

Noice! 👍🏼👍🏼

unplugged and replugged the wire harness next to the black communications jack and mine came to life.........Thanks again...

I love to see how you got that whipped up In-Shape I remember my mother had a 1967 or 68 coppertone Maytag with the green agitator turquoise whatever they called it

Do you really need to film 10 minutes of you vacuuming out the water? WTF.

I was hoping you had a way without totally taking the entire machine apart to replace the drain hose.

So so helpful! It was very easy to follow your steps to remove the drain pump - turns out mine was fine, it just had a bobby pin stuck in it 😅 Thank you for sharing your expertise!

Thanks for info but it was not easy to watch everything is shaking and we never saw the most important things like, where everything goes inn power, the pipe and how. Please get yourself a tripod stand so that you may aim the phone on whatever is important, than you may use both hands and the cam will not shake as much.

And you have access for this method for all springs around?

You measure vacuum in microns with a micron gauge. Under 500 to be exact. Never use your gauges as they are not accurate.

Uhh you can cut a cap tube with a cap tube cutter 🤔

So what's the verdict on this machine? I about to buy one for $50 for my rv.

I have this same model but in stainless barely use it and it died. Happened to my coworker as well died multiple times til they decided to change it. Im thinking of changing it too

Great video and idea

Hey, I found the board under the door. I un-plugged all of the ribbon cables and plugged them back into the board. My dishwasher is fixed!

How do you get to the door cover off to get to the module inside the door? I do not see any screws.

Good info, thanks. The from entry makes this job easier than on my old HE3T. Another Tech added swapping out the tension spring on the Belt/Idler. WRT Belt Tension, is there a standard WRT tension/play? Any test / inspection metrics on the belt "slack"?

Great tip, thanks!

Hello there! Can I ask why the spanner nut needs removal when removing the gear case? I ask because as far as I can tell (I haven't done one myself though) the spanner nut only serves to tighten the inner tub onto the drive block, and so not removing it shouldn't have any effect on removing or inserting the gearcase shaft, no?

I wish I had been there to help you get the washer back together. Bless your heart. ♥

I was just wondering. What does it mean when a person says: "BEFORE YOU FLAME ME" I don't understand what what that means. I never really knew or heard of that. What does that mean? And oh! By the way, wow! This is cool 😎 watching people repair appliances!! Way to go! 🤜🤛👍👊💪👏👏👏👏

My lights on my dishwasher would not power up either. I cut the power off the dishwasher for a one night and that still did not work. I removed the lower circuit board unplugging all the connections and left it unplugged for 30min reinstalled the board now the dishwasher is working again.I don’t know for how long though.

Error 13 is the ticket

My dryer shows an error msg @ 15 minutes unto the cycle. Any idea how to fix this? These machines are for shiat.

What the devil is that on your face?

Remove the capacitor right next to the connector on the UI board. 220mf 25v. YES remove it , replacing the bad cap does not fix the issue. For all of those who have a dead UI board try this. It's a smoothing capacitor I'm assuming. No harm removing it at your own risk. For some reason this solved a completely dead board. This dishwasher will still randomly come on but I can live with it. Below is a list of revisions for the board replacement GDF530PGM0CC WD21X24821 Original WD21X26182 (AP6985297) updated WD21X31909 new updated 220mf 25v capacitor You must lo

I can't tell you how much I appreciate you posting this. THANK YOU! My son and I just used your method to replace all 6 springs in my Speed Queen today and it worked like a charm. I made one small change, I didn't use wire, I used paracord which I think might be easier on the hands and it worked fine. (Paracord is just a small braided line that's used for parachute shrouds and hikers and campers use it a lot and it is very strong.) I see other guys suggesting different methods but I can't imagine anything slicker than this. Apparently you work alone but I'm not a pro like you so having my son help worked great for me and I would suggest that for other novices.

Glad I found this video. Parts coming in a couple days. You made that look super simple. I’m assuming that’s the part I need since dishwasher fills, heats, drains, but does not spray water and wash

Well this is disappointing. I have this exact dishwasher and I love it. But it has the same problem shown in the video. I was hoping it would be worth trying to repair but it looks like it’s an expensive option. I bought it used about a year ago and, fortunately, bought the extended warranty so I can get a replacement dishwasher at no cost.